mirror of
https://github.com/brain-hackers/u-boot-brain
synced 2024-09-11 15:23:22 +09:00
50 lines
1.8 KiB
Plaintext
50 lines
1.8 KiB
Plaintext
![]() |
Armada-8K PCIe DT details:
|
||
|
==========================
|
||
|
|
||
|
Armada-8k uses synopsis designware PCIe controller.
|
||
|
|
||
|
Required properties:
|
||
|
- compatible : should be "marvell,armada8k-pcie", "snps,dw-pcie".
|
||
|
- reg: base addresses and lengths of the pcie control and global control registers.
|
||
|
"ctrl" registers points to the global control registers, while the "config" space
|
||
|
points to the pcie configuration registers as mentioned in dw-pcie dt bindings in the link below.
|
||
|
- interrupt-map-mask and interrupt-map, standard PCI properties to
|
||
|
define the mapping of the PCIe interface to interrupt numbers.
|
||
|
- All other definitions as per generic PCI bindings
|
||
|
See Linux kernel documentation:
|
||
|
"Documentation/devicetree/bindings/pci/designware-pcie.txt"
|
||
|
|
||
|
Optional properties:
|
||
|
PHY support is still not supported for armada-8k, once it will, the following parameters can be used:
|
||
|
- phys : phandle to phy node associated with pcie controller.
|
||
|
- phy-names : must be "pcie-phy"
|
||
|
- marvell,reset-gpio : specifies a gpio that needs to be activated for plug-in
|
||
|
card reset signal release.
|
||
|
Example:
|
||
|
|
||
|
cpm_pcie0: pcie@f2600000 {
|
||
|
compatible = "marvell,armada8k-pcie", "snps,dw-pcie";
|
||
|
reg = <0 0xf2600000 0 0x10000>,
|
||
|
<0 0xf6f00000 0 0x80000>;
|
||
|
reg-names = "ctrl", "config";
|
||
|
#address-cells = <3>;
|
||
|
#size-cells = <2>;
|
||
|
#interrupt-cells = <1>;
|
||
|
device_type = "pci";
|
||
|
dma-coherent;
|
||
|
|
||
|
bus-range = <0 0xff>;
|
||
|
ranges =
|
||
|
/* downstream I/O */
|
||
|
<0x81000000 0 0xf9000000 0 0xf9000000 0 0x10000
|
||
|
/* non-prefetchable memory */
|
||
|
0x82000000 0 0xf6000000 0 0xf6000000 0 0xf00000>;
|
||
|
interrupt-map-mask = <0 0 0 0>;
|
||
|
interrupt-map = <0 0 0 0 &gic 0 GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
|
||
|
interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
|
||
|
num-lanes = <1>;
|
||
|
clocks = <&cpm_syscon0 1 13>;
|
||
|
marvell,reset-gpio = <&cpm_gpio1 20 GPIO_ACTIVE_HIGH>;
|
||
|
status = "disabled";
|
||
|
};
|