u-boot-brain/drivers/firmware/Makefile

obj-$(CONFIG_FIRMWARE)		+= firmware-uclass.o
obj-$(CONFIG_$(SPL_)ARM_PSCI_FW)	+= psci.o
obj-$(CONFIG_TI_SCI_PROTOCOL)	+= ti_sci.o
obj-$(CONFIG_SANDBOX)		+= firmware-sandbox.o
obj-$(CONFIG_ZYNQMP_FIRMWARE)	+= firmware-zynqmp.o
sysreset: psci: support system reset in a generic way with PSCI If the system is running PSCI firmware, the System Reset function (func ID: 0x80000009) is supposed to be handled by PSCI, that is, the SoC/board specific reset implementation should be moved to PSCI. U-Boot should call the PSCI service according to the arm-smccc manner. The arm-smccc is supported on ARMv7 or later. Especially, ARMv8 generation SoCs are likely to run ARM Trusted Firmware BL31. In this case, U-Boot is a non-secure world boot loader, so it should not be able to reset the system directly. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> 2017-04-14 11:10:24 +09:00			`obj-$(CONFIG_FIRMWARE) += firmware-uclass.o`
firmware: psci: introduce SPL_ARM_PSCI_FW Introduce a new macro SPL_ARM_PSCI_FW Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Stefano Babic <sbabic@denx.de> 2018-12-09 21:45:45 +09:00			`obj-$(CONFIG_$(SPL_)ARM_PSCI_FW) += psci.o`
firmware: Add basic support for TI System Control Interface (TI SCI) protocol Texas Instrument's System Control Interface (TI SCI) message protocol is used in Texas Instrument's System on Chip (SoC) such as those in the K3 family AM654 SoC to communicate between various compute processors with a central system controller entity. The TI SCI message protocol provides support for management of various hardware entities within the SoC. Add support driver to allow communication with system controller entity within the SoC using the mailbox client. This is mostly derived from the TI SCI driver in Linux located at drivers/firmware/ti_sci.c. Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Andreas Dannenberg <dannenberg@ti.com> 2018-08-27 19:27:32 +09:00			`obj-$(CONFIG_TI_SCI_PROTOCOL) += ti_sci.o`
dm: test: Add "/firmware" node scan test Add a test which verifies that all subnodes under "/firmware" nodes are scanned. Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org> Added 'imply FIRMWARE' to sandbox Kconfig to fix test failures, fixed ordering of lines in arch/sandbox/dts/test.dts and test/dm/Makefile, updated #if condition in drivers/firmware/firmware-uclass.c: Signed-off-by: Simon Glass <sjg@chromium.org> 2018-09-19 19:43:46 +09:00			`obj-$(CONFIG_SANDBOX) += firmware-sandbox.o`
zynqmp: firmware: Add Xilinx ZynqMP firmware driver Add simple ZynqMP firmware drive to populate child nodes under zynqmp_firmware DT node. Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> 2019-02-15 21:45:32 +09:00			`obj-$(CONFIG_ZYNQMP_FIRMWARE) += firmware-zynqmp.o`