commit 6f67e060083a84a4cc364eab6ae40c717165fb0c upstream.
Currently, when turbo is disabled (either by BIOS or by the user),
the intel_pstate driver reads the max non-turbo frequency from the
package-wide MSR_PLATFORM_INFO(0xce) register.
However, on asymmetric platforms it is possible in theory that small
and big core with HWP enabled might have different max non-turbo CPU
frequency, because MSR_HWP_CAPABILITIES is per-CPU scope according
to Intel Software Developer Manual.
The turbo max freq is already per-CPU in current code, so make
similar change to the max non-turbo frequency as well.
Reported-by: Wendy Wang <wendy.wang@intel.com>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
[ rjw: Subject and changelog edits ]
Cc: 4.18+ <stable@vger.kernel.org> # 4.18+: a45ee4d4e13b: cpufreq: intel_pstate: Change intel_pstate_get_hwp_max() argument
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit eacc9c5a927e474c173a5d53dd7fb8e306511768 ]
This fixes the behavior of the scaling_max_freq and scaling_min_freq
sysfs files in systems which had turbo disabled by the BIOS.
Caleb noticed that the HWP is programmed to operate in the wrong
P-state range on his system when the CPUFREQ policy min/max frequency
is set via sysfs. This seems to be because in his system
intel_pstate_get_hwp_max() is returning the maximum turbo P-state even
though turbo was disabled by the BIOS, which causes intel_pstate to
scale kHz frequencies incorrectly e.g. setting the maximum turbo
frequency whenever the maximum guaranteed frequency is requested via
sysfs.
Tested-by: Caleb Callaway <caleb.callaway@intel.com>
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
[ rjw: Minor subject edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 43298db3009f06fe5c69e1ca8b6cfc2565772fa1 ]
After commit f6ebbcf08f37 ("cpufreq: intel_pstate: Implement passive
mode with HWP enabled") it is possible to change the driver status
to "off" via sysfs with HWP enabled, which effectively causes the
driver to unregister itself, but HWP remains active and it forces the
minimum performance, so even if another cpufreq driver is loaded,
it will not be able to control the CPU frequency.
For this reason, make the driver refuse to change the status to
"off" with HWP enabled.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit de002c55cadfc2f6cdf0ed427526f6085d240238 ]
Because intel_pstate_set_energy_pref_index() reads and writes the
MSR_HWP_REQUEST register without using the cached value of it used by
intel_pstate_hwp_boost_up() and intel_pstate_hwp_boost_down(), those
functions may overwrite the value written by it and so the EPP value
set via sysfs may be lost.
To avoid that, make intel_pstate_set_energy_pref_index() take the
cached value of MSR_HWP_REQUEST just like the other two routines
mentioned above and update it with the new EPP value coming from
user space in addition to updating the MSR.
Note that the MSR itself still needs to be updated too in case
hwp_boost is unset or the boosting mechanism is not active at the
EPP change time.
Fixes: e0efd5be63 ("cpufreq: intel_pstate: Add HWP boost utility and sched util hooks")
Reported-by: Francisco Jerez <currojerez@riseup.net>
Cc: 4.18+ <stable@vger.kernel.org> # 4.18+: 3da97d4db8ee cpufreq: intel_pstate: Rearrange ...
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4daca379c703ff55edc065e8e5173dcfeecf0148 ]
The MSR_TURBO_RATIO_LIMIT can be 0. This is not an error. User can update
this MSR via BIOS settings on some systems or can use msr tools to update.
Also some systems boot with value = 0.
This results in display of cpufreq/cpuinfo_max_freq wrong. This value
will be equal to cpufreq/base_frequency, even though turbo is enabled.
But platform will still function normally in HWP mode as we get max
1-core frequency from the MSR_HWP_CAPABILITIES. This MSR is already used
to calculate cpu->pstate.turbo_freq, which is used for to set
policy->cpuinfo.max_freq. But some other places cpu->pstate.turbo_pstate
is used. For example to set policy->max.
To fix this, also update cpu->pstate.turbo_pstate when updating
cpu->pstate.turbo_freq.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8c539776ac83c0857395e1ccc9c6b516521a2d32 ]
Make a note of the first time we discover the turbo mode has been
disabled by the BIOS, as otherwise we complain every time we try to
update the mode.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1e4f63aecb53e48468661e922fc2fa3b83e55722 upstream.
In the process of modifying a cpufreq policy, the cpufreq core makes
a copy of it including all of the internals which is stored on the
CPU stack. Because struct cpufreq_policy is relatively large, this
may cause the size of the stack frame to exceed the 2 KB limit and
so the GCC complains when -Wframe-larger-than= is used.
In fact, it is not necessary to copy the entire policy structure
in order to modify it, however.
First, because cpufreq_set_policy() obtains the min and max policy
limits from frequency QoS now, it is not necessary to pass the limits
to it from the callers. The only things that need to be passed to it
from there are the new governor pointer or (if there is a built-in
governor in the driver) the "policy" value representing the governor
choice. They both can be passed as individual arguments, though, so
make cpufreq_set_policy() take them this way and rework its callers
accordingly. This avoids making copies of cpufreq policies in the
callers of cpufreq_set_policy().
Second, cpufreq_set_policy() still needs to pass the new policy
data to the ->verify() callback of the cpufreq driver whose task
is to sanitize the min and max policy limits. It still does not
need to make a full copy of struct cpufreq_policy for this purpose,
but it needs to pass a few items from it to the driver in case they
are needed (different drivers have different needs in that respect
and all of them have to be covered). For this reason, introduce
struct cpufreq_policy_data to hold copies of the members of
struct cpufreq_policy used by the existing ->verify() driver
callbacks and pass a pointer to a temporary structure of that
type to ->verify() (instead of passing a pointer to full struct
cpufreq_policy to it).
While at it, notice that intel_pstate and longrun don't really need
to verify the "policy" value in struct cpufreq_policy, so drop those
check from them to avoid copying "policy" into struct
cpufreq_policy_data (which allows it to be slightly smaller).
Also while at it fix up white space in a couple of places and make
cpufreq_set_policy() static (as it can be so).
Fixes: 3000ce3c52 ("cpufreq: Use per-policy frequency QoS")
Link: https://lore.kernel.org/linux-pm/CAMuHMdX6-jb1W8uC2_237m8ctCpsnGp=JCxqt8pCWVqNXHmkVg@mail.gmail.com
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: 5.4+ <stable@vger.kernel.org> # 5.4+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The max value of EPB can only be 0x0F. Attempting to set more than that
triggers an "unchecked MSR access error" warning which happens in
intel_pstate_hwp_force_min_perf() called via cpufreq stop_cpu().
However, it is not even necessary to touch the EPB from intel_pstate,
because it is restored on every CPU online by the intel_epb.c code,
so let that code do the right thing and drop the redundant (and
incorrect) EPB update from intel_pstate.
Fixes: af3b7379e2 ("cpufreq: intel_pstate: Force HWP min perf before offline")
Reported-by: Qian Cai <cai@lca.pw>
Cc: 5.2+ <stable@vger.kernel.org> # 5.2+
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
[ rjw: Changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Replace the CPU device PM QoS used for the management of min and max
frequency constraints in cpufreq (and its users) with per-policy
frequency QoS to avoid problems with cpufreq policies covering
more then one CPU.
Namely, a cpufreq driver is registered with the subsys interface
which calls cpufreq_add_dev() for each CPU, starting from CPU0, so
currently the PM QoS notifiers are added to the first CPU in the
policy (i.e. CPU0 in the majority of cases).
In turn, when the cpufreq driver is unregistered, the subsys interface
doing that calls cpufreq_remove_dev() for each CPU, starting from CPU0,
and the PM QoS notifiers are only removed when cpufreq_remove_dev() is
called for the last CPU in the policy, say CPUx, which as a rule is
not CPU0 if the policy covers more than one CPU. Then, the PM QoS
notifiers cannot be removed, because CPUx does not have them, and
they are still there in the device PM QoS notifiers list of CPU0,
which prevents new PM QoS notifiers from being registered for CPU0
on the next attempt to register the cpufreq driver.
The same issue occurs when the first CPU in the policy goes offline
before unregistering the driver.
After this change it does not matter which CPU is the policy CPU at
the driver registration time and whether or not it is online all the
time, because the frequency QoS is per policy and not per CPU.
Fixes: 67d874c3b2 ("cpufreq: Register notifiers with the PM QoS framework")
Reported-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Reported-by: Sudeep Holla <sudeep.holla@arm.com>
Tested-by: Sudeep Holla <sudeep.holla@arm.com>
Diagnosed-by: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://lore.kernel.org/linux-pm/5ad2624194baa2f53acc1f1e627eb7684c577a19.1562210705.git.viresh.kumar@linaro.org/T/#md2d89e95906b8c91c15f582146173dce2e86e99f
Link: https://lore.kernel.org/linux-pm/20191017094612.6tbkwoq4harsjcqv@vireshk-i7/T/#m30d48cc23b9a80467fbaa16e30f90b3828a5a29b
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
- Rework the main suspend-to-idle control flow to avoid repeating
"noirq" device resume and suspend operations in case of spurious
wakeups from the ACPI EC and decouple the ACPI EC wakeups support
from the LPS0 _DSM support (Rafael Wysocki).
- Extend the wakeup sources framework to expose wakeup sources as
device objects in sysfs (Tri Vo, Stephen Boyd).
- Expose system suspend statistics in sysfs (Kalesh Singh).
- Introduce a new haltpoll cpuidle driver and a new matching
governor for virtualized guests wanting to do guest-side polling
in the idle loop (Marcelo Tosatti, Joao Martins, Wanpeng Li,
Stephen Rothwell).
- Fix the menu and teo cpuidle governors to allow the scheduler tick
to be stopped if PM QoS is used to limit the CPU idle state exit
latency in some cases (Rafael Wysocki).
- Increase the resolution of the play_idle() argument to microseconds
for more fine-grained injection of CPU idle cycles (Daniel Lezcano).
- Switch over some users of cpuidle notifiers to the new QoS-based
frequency limits and drop the CPUFREQ_ADJUST and CPUFREQ_NOTIFY
policy notifier events (Viresh Kumar).
- Add new cpufreq driver based on nvmem for sun50i (Yangtao Li).
- Add support for MT8183 and MT8516 to the mediatek cpufreq driver
(Andrew-sh.Cheng, Fabien Parent).
- Add i.MX8MN support to the imx-cpufreq-dt cpufreq driver (Anson
Huang).
- Add qcs404 to cpufreq-dt-platdev blacklist (Jorge Ramirez-Ortiz).
- Update the qcom cpufreq driver (among other things, to make it
easier to extend and to use kryo cpufreq for other nvmem-based
SoCs) and add qcs404 support to it (Niklas Cassel, Douglas
RAILLARD, Sibi Sankar, Sricharan R).
- Fix assorted issues and make assorted minor improvements in the
cpufreq code (Colin Ian King, Douglas RAILLARD, Florian Fainelli,
Gustavo Silva, Hariprasad Kelam).
- Add new devfreq driver for NVidia Tegra20 (Dmitry Osipenko, Arnd
Bergmann).
- Add new Exynos PPMU events to devfreq events and extend that
mechanism (Lukasz Luba).
- Fix and clean up the exynos-bus devfreq driver (Kamil Konieczny).
- Improve devfreq documentation and governor code, fix spelling
typos in devfreq (Ezequiel Garcia, Krzysztof Kozlowski, Leonard
Crestez, MyungJoo Ham, Gaël PORTAY).
- Add regulators enable and disable to the OPP (operating performance
points) framework (Kamil Konieczny).
- Update the OPP framework to support multiple opp-suspend properties
(Anson Huang).
- Fix assorted issues and make assorted minor improvements in the OPP
code (Niklas Cassel, Viresh Kumar, Yue Hu).
- Clean up the generic power domains (genpd) framework (Ulf Hansson).
- Clean up assorted pieces of power management code and documentation
(Akinobu Mita, Amit Kucheria, Chuhong Yuan).
- Update the pm-graph tool to version 5.5 including multiple fixes
and improvements (Todd Brandt).
- Update the cpupower utility (Benjamin Weis, Geert Uytterhoeven,
Sébastien Szymanski).
-----BEGIN PGP SIGNATURE-----
iQJGBAABCAAwFiEE4fcc61cGeeHD/fCwgsRv/nhiVHEFAl2ArZ4SHHJqd0Byand5
c29ja2kubmV0AAoJEILEb/54YlRxgfYQAK80hs43vWQDmp7XKrN4pQe8+qYULAGO
fBfrFl+NG9y/cnuqnt3NtA8MoyNsMMkMLkpkEDMfSbYqqH5ehEzX5+uGJWiWx8+Y
oH5KU8MH7Tj/utYaalGzDt0AHfHZDIGC0NCUNQJVtE/4mOANFabwsCwscp4MrD5Q
WjFN8U4BrsmWgJdZ/U9QIWcDZ0I+1etCF+rZG2yxSv31FMq2Zk/Qm4YyobqCvQFl
TR9rxl08wqUmIYIz5cDjt/3AKH7NLLDqOTstbCL7cmufM5XPFc1yox69xc89UrIa
4AMgmDp7SMwFG/gdUPof0WQNmx7qxmiRAPleAOYBOZW/8jPNZk2y+RhM5NeF72m7
AFqYiuxqatkSb4IsT8fLzH9IUZOdYr8uSmoMQECw+MHdApaKFjFV8Lb/qx5+AwkD
y7pwys8dZSamAjAf62eUzJDWcEwkNrujIisGrIXrVHb7ISbweskMOmdAYn9p4KgP
dfRzpJBJ45IaMIdbaVXNpg3rP7Apfs7X1X+/ZhG6f+zHH3zYwr8Y81WPqX8WaZJ4
qoVCyxiVWzMYjY2/1lzjaAdqWojPWHQ3or3eBaK52DouyG3jY6hCDTLwU7iuqcCX
jzAtrnqrNIKufvaObEmqcmYlIIOFT7QaJCtGUSRFQLfSon8fsVSR7LLeXoAMUJKT
JWQenuNaJngK
=TBDQ
-----END PGP SIGNATURE-----
Merge tag 'pm-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These include a rework of the main suspend-to-idle code flow (related
to the handling of spurious wakeups), a switch over of several users
of cpufreq notifiers to QoS-based limits, a new devfreq driver for
Tegra20, a new cpuidle driver and governor for virtualized guests, an
extension of the wakeup sources framework to expose wakeup sources as
device objects in sysfs, and more.
Specifics:
- Rework the main suspend-to-idle control flow to avoid repeating
"noirq" device resume and suspend operations in case of spurious
wakeups from the ACPI EC and decouple the ACPI EC wakeups support
from the LPS0 _DSM support (Rafael Wysocki).
- Extend the wakeup sources framework to expose wakeup sources as
device objects in sysfs (Tri Vo, Stephen Boyd).
- Expose system suspend statistics in sysfs (Kalesh Singh).
- Introduce a new haltpoll cpuidle driver and a new matching governor
for virtualized guests wanting to do guest-side polling in the idle
loop (Marcelo Tosatti, Joao Martins, Wanpeng Li, Stephen Rothwell).
- Fix the menu and teo cpuidle governors to allow the scheduler tick
to be stopped if PM QoS is used to limit the CPU idle state exit
latency in some cases (Rafael Wysocki).
- Increase the resolution of the play_idle() argument to microseconds
for more fine-grained injection of CPU idle cycles (Daniel
Lezcano).
- Switch over some users of cpuidle notifiers to the new QoS-based
frequency limits and drop the CPUFREQ_ADJUST and CPUFREQ_NOTIFY
policy notifier events (Viresh Kumar).
- Add new cpufreq driver based on nvmem for sun50i (Yangtao Li).
- Add support for MT8183 and MT8516 to the mediatek cpufreq driver
(Andrew-sh.Cheng, Fabien Parent).
- Add i.MX8MN support to the imx-cpufreq-dt cpufreq driver (Anson
Huang).
- Add qcs404 to cpufreq-dt-platdev blacklist (Jorge Ramirez-Ortiz).
- Update the qcom cpufreq driver (among other things, to make it
easier to extend and to use kryo cpufreq for other nvmem-based
SoCs) and add qcs404 support to it (Niklas Cassel, Douglas
RAILLARD, Sibi Sankar, Sricharan R).
- Fix assorted issues and make assorted minor improvements in the
cpufreq code (Colin Ian King, Douglas RAILLARD, Florian Fainelli,
Gustavo Silva, Hariprasad Kelam).
- Add new devfreq driver for NVidia Tegra20 (Dmitry Osipenko, Arnd
Bergmann).
- Add new Exynos PPMU events to devfreq events and extend that
mechanism (Lukasz Luba).
- Fix and clean up the exynos-bus devfreq driver (Kamil Konieczny).
- Improve devfreq documentation and governor code, fix spelling typos
in devfreq (Ezequiel Garcia, Krzysztof Kozlowski, Leonard Crestez,
MyungJoo Ham, Gaël PORTAY).
- Add regulators enable and disable to the OPP (operating performance
points) framework (Kamil Konieczny).
- Update the OPP framework to support multiple opp-suspend properties
(Anson Huang).
- Fix assorted issues and make assorted minor improvements in the OPP
code (Niklas Cassel, Viresh Kumar, Yue Hu).
- Clean up the generic power domains (genpd) framework (Ulf Hansson).
- Clean up assorted pieces of power management code and documentation
(Akinobu Mita, Amit Kucheria, Chuhong Yuan).
- Update the pm-graph tool to version 5.5 including multiple fixes
and improvements (Todd Brandt).
- Update the cpupower utility (Benjamin Weis, Geert Uytterhoeven,
Sébastien Szymanski)"
* tag 'pm-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (126 commits)
cpuidle-haltpoll: Enable kvm guest polling when dedicated physical CPUs are available
cpuidle-haltpoll: do not set an owner to allow modunload
cpuidle-haltpoll: return -ENODEV on modinit failure
cpuidle-haltpoll: set haltpoll as preferred governor
cpuidle: allow governor switch on cpuidle_register_driver()
PM: runtime: Documentation: add runtime_status ABI document
pm-graph: make setVal unbuffered again for python2 and python3
powercap: idle_inject: Use higher resolution for idle injection
cpuidle: play_idle: Increase the resolution to usec
cpuidle-haltpoll: vcpu hotplug support
cpufreq: Add qcs404 to cpufreq-dt-platdev blacklist
cpufreq: qcom: Add support for qcs404 on nvmem driver
cpufreq: qcom: Refactor the driver to make it easier to extend
cpufreq: qcom: Re-organise kryo cpufreq to use it for other nvmem based qcom socs
dt-bindings: opp: Add qcom-opp bindings with properties needed for CPR
dt-bindings: opp: qcom-nvmem: Support pstates provided by a power domain
Documentation: cpufreq: Update policy notifier documentation
cpufreq: Remove CPUFREQ_ADJUST and CPUFREQ_NOTIFY policy notifier events
PM / Domains: Verify PM domain type in dev_pm_genpd_set_performance_state()
PM / Domains: Simplify genpd_lookup_dev()
...
Currently big microservers have _XEON_D while small microservers have
_X, Make it uniformly: _D.
for i in `git grep -l "\(INTEL_FAM6_\|VULNWL_INTEL\|INTEL_CPU_FAM6\).*_\(X\|XEON_D\)"`
do
sed -i -e 's/\(\(INTEL_FAM6_\|VULNWL_INTEL\|INTEL_CPU_FAM6\).*ATOM.*\)_X/\1_D/g' \
-e 's/\(\(INTEL_FAM6_\|VULNWL_INTEL\|INTEL_CPU_FAM6\).*\)_XEON_D/\1_D/g' ${i}
done
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Cc: x86@kernel.org
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Borislav Petkov <bp@alien8.de>
Link: https://lkml.kernel.org/r/20190827195122.677152989@infradead.org
Currently big core clients with extra graphics on have:
- _G
- _GT3E
Make it uniformly: _G
for i in `git grep -l "\(INTEL_FAM6_\|VULNWL_INTEL\|INTEL_CPU_FAM6\).*_GT3E"`
do
sed -i -e 's/\(\(INTEL_FAM6_\|VULNWL_INTEL\|INTEL_CPU_FAM6\).*\)_GT3E/\1_G/g' ${i}
done
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Cc: x86@kernel.org
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Borislav Petkov <bp@alien8.de>
Link: https://lkml.kernel.org/r/20190827195122.622802314@infradead.org
Currently big core mobile chips have either:
- _L
- _ULT
- _MOBILE
Make it uniformly: _L.
for i in `git grep -l "\(INTEL_FAM6_\|VULNWL_INTEL\|INTEL_CPU_FAM6\).*_\(MOBILE\|ULT\)"`
do
sed -i -e 's/\(\(INTEL_FAM6_\|VULNWL_INTEL\|INTEL_CPU_FAM6\).*\)_\(MOBILE\|ULT\)/\1_L/g' ${i}
done
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Cc: x86@kernel.org
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20190827195122.568978530@infradead.org
Currently the big core client models either have:
- no OPTDIFF
- _CORE
- _DESKTOP
Make it uniformly: 'no OPTDIFF'.
for i in `git grep -l "\(INTEL_FAM6_\|VULNWL_INTEL\|INTEL_CPU_FAM6\).*_\(CORE\|DESKTOP\)"`
do
sed -i -e 's/\(\(INTEL_FAM6_\|VULNWL_INTEL\|INTEL_CPU_FAM6\).*\)_\(CORE\|DESKTOP\)/\1/g' ${i}
done
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Cc: x86@kernel.org
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20190827195122.513945586@infradead.org
Intel pstate driver exposes min_perf_pct and max_perf_pct sysfs files,
which can be used to force a limit on the min/max P state of the driver.
Though these files eventually control the min/max frequencies that the
CPUs will run at, they don't make a change to policy->min/max values.
When the values of these files are changed (in passive mode of the
driver), it leads to calling ->limits() callback of the cpufreq
governors, like schedutil. On a call to it the governors shall
forcefully update the frequency to come within the limits. Since the
limits, i.e. policy->min/max, aren't updated by the driver, the
governors fails to get the target freq within limit and sometimes aborts
the update believing that the frequency is already set to the target
value.
This patch implements the QoS supported frequency constraints to update
policy->min/max values whenever min_perf_pct or max_perf_pct files are
updated. This is only done for the passive mode as of now, as the driver
is already working fine in active mode.
Fixes: ecd2884291 ("cpufreq: schedutil: Don't set next_freq to UINT_MAX")
Reported-by: Doug Smythies <dsmythies@telus.net>
Tested-by: Doug Smythies <dsmythies@telus.net>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The implementation of intel_pstate_update_max_freq() is quite similar to
refresh_frequency_limits(), lets reuse it.
Finding minimum of policy->user_policy.max and policy->cpuinfo.max_freq
in intel_pstate_update_max_freq() is redundant as cpufreq_set_policy()
will call the ->verify() callback of intel-pstate driver, which will do
this comparison anyway and so dropping it from
intel_pstate_update_max_freq() doesn't harm.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation version 2 of the license
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 315 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Armijn Hemel <armijn@tjaldur.nl>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190115.503150771@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using static_cpu_has() is pointless on those paths, convert them to the
boot_cpu_has() variant.
No functional changes.
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
While the cpuinfo.max_freq value doesn't really matter for
intel_pstate in the active mode, in the passive mode it is used by
governors as the maximum physical frequency of the CPU and the
results of governor computations generally depend on it. Also it
is made available to user space via sysfs and it should match the
current HW configuration.
For this reason, make intel_pstate update cpuinfo.max_freq for all
CPUs if it detects a global change of turbo frequency settings from
"disable" to "enable" or the other way associated with a _PPC change
notification from the platform firmware.
Note that policy_is_inactive(), cpufreq_cpu_acquire(),
cpufreq_cpu_release(), and cpufreq_set_policy() need to be made
available to it for this purpose.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=200759
Reported-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Tested-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
In some cases, the platform firmware disables or enables turbo
frequencies for all CPUs globally before triggering a _PPC change
notification for one of them. Obviously, that global change affects
all CPUs, not just the notified one, and it needs to be acted upon by
cpufreq.
The intel_pstate driver is able to detect such global changes of
the settings, but it also needs to update policy limits for all
CPUs if that happens, in particular if turbo frequencies are
enabled globally - to allow them to be used.
For this reason, introduce a new cpufreq driver callback to be
invoked on _PPC notifications, if present, instead of simply
calling cpufreq_update_policy() for the notified CPU and make
intel_pstate use it to trigger policy updates for all CPUs
in the system if global settings change.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=200759
Reported-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Tested-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
This driver is Intel-only so loading on anything which is not Intel is
pointless. Prevent it from doing so.
While at it, correct the "not supported" print statement to say CPU
"model" which is what that test does.
Fixes: 076b862c7e (cpufreq: intel_pstate: Add reasons for failure and debug messages)
Suggested-by: Erwan Velu <e.velu@criteo.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The ACPI specification states that if the "Guaranteed Performance
Register" is not implemented, the OSPM assumes guaranteed performance
to always be equal to nominal performance.
So for invalid or unimplemented guaranteed performance register, use
nominal performance as guaranteed performance.
This change will fall back to nominal_perf when guranteed_perf is
invalid. If nominal_perf is also invalid or not present, fall back
to the existing implementation, which is to read from HWP Capabilities
MSR.
Fixes: 86d333a8cc ("cpufreq: intel_pstate: Add base_frequency attribute")
Suggested-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: 4.20+ <stable@vger.kernel.org> # 4.20+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
After commit b8bd1581aa ("cpufreq: intel_pstate: Rework iowait
boosting to be less aggressive") the handling of the case when
the SCHED_CPUFREQ_IOWAIT flag is set again after a few iterations of
intel_pstate_update_util() is a bit inconsistent, because the
new value of cpu->iowait_boost may be lower than ONE_EIGHTH_FP
if it was set before, but has not dropped down to zero just yet.
Fix that up by ensuring that the new value of cpu->iowait_boost
will always be at least ONE_EIGHTH_FP then.
Fixes: b8bd1581aa ("cpufreq: intel_pstate: Rework iowait boosting to be less aggressive")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The current iowait boosting mechanism in intel_pstate_update_util()
is quite aggressive, as it goes to the maximum P-state right away,
and may cause excessive amounts of energy to be used, which is not
desirable and arguably isn't necessary too.
Follow commit a5a0809bc5 ("cpufreq: schedutil: Make iowait boost
more energy efficient") that reworked the analogous iowait boost
mechanism in the schedutil governor and make the iowait boosting
in intel_pstate_update_util() work along the same lines.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There is only one caller of intel_pstate_get_base_pstate() and it is
more straightforward to carry out the computation directly in the
caller, so do that and drop intel_pstate_get_base_pstate().
No intentional changes of behavior.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
After commit 1a4fe38add ("cpufreq: intel_pstate: Remove max/min
fractions to limit performance") the initial value of the pstate local
variable in intel_pstate_max_within_limits() and the initial value of
the max_pstate local variable in intel_pstate_prepare_request() are
both immediately discarded, so initialize both these variables to
their target values upfront.
No intentional changes of behavior.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The init code path has several exceptions where the driver can
decide not to load.
As CONFIG_X86_INTEL_PSTATE is generally set to Y, the return code is
not reachable. The initialization code is neither verbose of the
reason why it did choose to prematurely exit, so it is difficult for
a user to determine, on a given platform, why the driver didn't load
properly.
This patch is about reporting to the user the reason/context of why
the driver failed to load. That is a precious hint when debugging
a platform.
Signed-off-by: Erwan Velu <e.velu@criteo.com>
[ rjw: Subject & changelog, minor fixups ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cpufreq_global_kobject is created using kobject_create_and_add()
helper, which assigns the kobj_type as dynamic_kobj_ktype and show/store
routines are set to kobj_attr_show() and kobj_attr_store().
These routines pass struct kobj_attribute as an argument to the
show/store callbacks. But all the cpufreq files created using the
cpufreq_global_kobject expect the argument to be of type struct
attribute. Things work fine currently as no one accesses the "attr"
argument. We may not see issues even if the argument is used, as struct
kobj_attribute has struct attribute as its first element and so they
will both get same address.
But this is logically incorrect and we should rather use struct
kobj_attribute instead of struct global_attr in the cpufreq core and
drivers and the show/store callbacks should take struct kobj_attribute
as argument instead.
This bug is caught using CFI CLANG builds in android kernel which
catches mismatch in function prototypes for such callbacks.
Reported-by: Donghee Han <dh.han@samsung.com>
Reported-by: Sangkyu Kim <skwith.kim@samsung.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull RCU updates from Ingo Molnar:
"The biggest RCU changes in this cycle were:
- Convert RCU's BUG_ON() and similar calls to WARN_ON() and similar.
- Replace calls of RCU-bh and RCU-sched update-side functions to
their vanilla RCU counterparts. This series is a step towards
complete removal of the RCU-bh and RCU-sched update-side functions.
( Note that some of these conversions are going upstream via their
respective maintainers. )
- Documentation updates, including a number of flavor-consolidation
updates from Joel Fernandes.
- Miscellaneous fixes.
- Automate generation of the initrd filesystem used for rcutorture
testing.
- Convert spin_is_locked() assertions to instead use lockdep.
( Note that some of these conversions are going upstream via their
respective maintainers. )
- SRCU updates, especially including a fix from Dennis Krein for a
bag-on-head-class bug.
- RCU torture-test updates"
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (112 commits)
rcutorture: Don't do busted forward-progress testing
rcutorture: Use 100ms buckets for forward-progress callback histograms
rcutorture: Recover from OOM during forward-progress tests
rcutorture: Print forward-progress test age upon failure
rcutorture: Print time since GP end upon forward-progress failure
rcutorture: Print histogram of CB invocation at OOM time
rcutorture: Print GP age upon forward-progress failure
rcu: Print per-CPU callback counts for forward-progress failures
rcu: Account for nocb-CPU callback counts in RCU CPU stall warnings
rcutorture: Dump grace-period diagnostics upon forward-progress OOM
rcutorture: Prepare for asynchronous access to rcu_fwd_startat
torture: Remove unnecessary "ret" variables
rcutorture: Affinity forward-progress test to avoid housekeeping CPUs
rcutorture: Break up too-long rcu_torture_fwd_prog() function
rcutorture: Remove cbflood facility
torture: Bring any extra CPUs online during kernel startup
rcutorture: Add call_rcu() flooding forward-progress tests
rcutorture/formal: Replace synchronize_sched() with synchronize_rcu()
tools/kernel.h: Replace synchronize_sched() with synchronize_rcu()
net/decnet: Replace rcu_barrier_bh() with rcu_barrier()
...
Force HWP Request MAX = HWP Request MIN = HWP Capability MIN and EPP to
0xFF. In this way the performance limits on the offlined CPU will not
influence performance limits on its sibling CPU, which is still online.
If the sibling CPU is calling for higher performance, it will impact the
max core performance. Here core performance will follow higher of the
performance requests from each sibling.
Reported-and-tested-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Now that synchronize_rcu() waits for preempt-disable regions of code
as well as RCU read-side critical sections, synchronize_sched() can be
replaced by synchronize_rcu(). This commit therefore makes this change.
Signed-off-by: Paul E. McKenney <paulmck@linux.ibm.com>
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: Len Brown <lenb@kernel.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: <linux-pm@vger.kernel.org>
While at it, add a few comments which config options #ifdef
and #else statements refer to.
Fixes: 86d333a8cc (cpufreq: intel_pstate: Add base_frequency attribute)
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull perf updates from Ingo Molnar:
"The main updates in this cycle were:
- Lots of perf tooling changes too voluminous to list (big perf trace
and perf stat improvements, lots of libtraceevent reorganization,
etc.), so I'll list the authors and refer to the changelog for
details:
Benjamin Peterson, Jérémie Galarneau, Kim Phillips, Peter
Zijlstra, Ravi Bangoria, Sangwon Hong, Sean V Kelley, Steven
Rostedt, Thomas Gleixner, Ding Xiang, Eduardo Habkost, Thomas
Richter, Andi Kleen, Sanskriti Sharma, Adrian Hunter, Tzvetomir
Stoyanov, Arnaldo Carvalho de Melo, Jiri Olsa.
... with the bulk of the changes written by Jiri Olsa, Tzvetomir
Stoyanov and Arnaldo Carvalho de Melo.
- Continued intel_rdt work with a focus on playing well with perf
events. This also imported some non-perf RDT work due to
dependencies. (Reinette Chatre)
- Implement counter freezing for Arch Perfmon v4 (Skylake and newer).
This allows to speed up the PMI handler by avoiding unnecessary MSR
writes and make it more accurate. (Andi Kleen)
- kprobes cleanups and simplification (Masami Hiramatsu)
- Intel Goldmont PMU updates (Kan Liang)
- ... plus misc other fixes and updates"
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (155 commits)
kprobes/x86: Use preempt_enable() in optimized_callback()
x86/intel_rdt: Prevent pseudo-locking from using stale pointers
kprobes, x86/ptrace.h: Make regs_get_kernel_stack_nth() not fault on bad stack
perf/x86/intel: Export mem events only if there's PEBS support
x86/cpu: Drop pointless static qualifier in punit_dev_state_show()
x86/intel_rdt: Fix initial allocation to consider CDP
x86/intel_rdt: CBM overlap should also check for overlap with CDP peer
x86/intel_rdt: Introduce utility to obtain CDP peer
tools lib traceevent, perf tools: Move struct tep_handler definition in a local header file
tools lib traceevent: Separate out tep_strerror() for strerror_r() issues
perf python: More portable way to make CFLAGS work with clang
perf python: Make clang_has_option() work on Python 3
perf tools: Free temporary 'sys' string in read_event_files()
perf tools: Avoid double free in read_event_file()
perf tools: Free 'printk' string in parse_ftrace_printk()
perf tools: Cleanup trace-event-info 'tdata' leak
perf strbuf: Match va_{add,copy} with va_end
perf test: S390 does not support watchpoints in test 22
perf auxtrace: Include missing asm/bitsperlong.h to get BITS_PER_LONG
tools include: Adopt linux/bits.h
...
Expose base_frequency to user space via cpufreq sysfs when HWP is in
use.
This HWP base frequency is read from the ACPI _CPC object if present,
or from the HWP Capabilities MSR otherwise.
On the majority of the HWP platforms the _CPC object will point to
the HWP Capabilities MSR using the "Functional Fixed Hardware"
address space type. The address space type also can simply be
ACPI_TYPE_INTEGER, however, in which case the platform firmware
can set its value at the initialization time based on the system
constraints.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
[ rjw: Changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Going primarily by:
https://en.wikipedia.org/wiki/List_of_Intel_Atom_microprocessors
with additional information gleaned from other related pages; notably:
- Bonnell shrink was called Saltwell
- Moorefield is the Merriefield refresh which makes it Airmont
The general naming scheme is: FAM6_ATOM_UARCH_SOCTYPE
for i in `git grep -l FAM6_ATOM` ; do
sed -i -e 's/ATOM_PINEVIEW/ATOM_BONNELL/g' \
-e 's/ATOM_LINCROFT/ATOM_BONNELL_MID/' \
-e 's/ATOM_PENWELL/ATOM_SALTWELL_MID/g' \
-e 's/ATOM_CLOVERVIEW/ATOM_SALTWELL_TABLET/g' \
-e 's/ATOM_CEDARVIEW/ATOM_SALTWELL/g' \
-e 's/ATOM_SILVERMONT1/ATOM_SILVERMONT/g' \
-e 's/ATOM_SILVERMONT2/ATOM_SILVERMONT_X/g' \
-e 's/ATOM_MERRIFIELD/ATOM_SILVERMONT_MID/g' \
-e 's/ATOM_MOOREFIELD/ATOM_AIRMONT_MID/g' \
-e 's/ATOM_DENVERTON/ATOM_GOLDMONT_X/g' \
-e 's/ATOM_GEMINI_LAKE/ATOM_GOLDMONT_PLUS/g' ${i}
done
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: dave.hansen@linux.intel.com
Cc: len.brown@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
When HWP is active turbo active ratio is not used, so we should allow
policy max frequency above turbo activation ratio to be set. When HWP is
not active, then any policy max frequency above turbo activation ratio
can result upto max one-core turbo frequency.
This fix helps better thermal control in turbo region when other methods
like "Running Average Power Limit" is not available to use.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Dynamic boosting of HWP performance on IO wake showed significant
improvement to IO workloads. This series was intended for Skylake Xeon
platforms only and feature was enabled by default based on CPU model
number.
But some Xeon platforms reused the Skylake desktop CPU model number. This
caused some undesirable side effects to some graphics workloads. Since
they are heavily IO bound, the increase in CPU performance decreased the
power available for GPU to do its computing and hence decrease in graphics
benchmark performance.
For example on a Skylake desktop, GpuTest benchmark showed average FPS
reduction from 529 to 506.
This change makes sure that HWP boost feature is only enabled for Skylake
server platforms by using ACPI FADT preferred PM Profile. If some desktop
users wants to get benefit of boost, they can still enable boost from
intel_pstate sysfs attribute "hwp_dynamic_boost".
Fixes: 41ab43c9c8 (cpufreq: intel_pstate: enable boost for Skylake Xeon)
Link: https://bugs.freedesktop.org/show_bug.cgi?id=107410
Reported-by: Eero Tamminen <eero.t.tamminen@intel.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Reviewed-by: Francisco Jerez <currojerez@riseup.net>
Acked-by: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
On HWP platforms with Turbo 3.0, the HWP capability max ratio shows the
maximum ratio of that core, which can be different than other cores. If
we show the correct maximum frequency in cpufreq sysfs via
cpuinfo_max_freq and scaling_max_freq then, user can know which cores
can run faster for pinning some high priority tasks.
Currently the max turbo frequency is shown as max frequency, which is
the max of all cores, even if some cores can't reach that frequency
even for single threaded workload.
But it is possible that max ratio in HWP capabilities is set as 0xFF or
some high invalid value (E.g. One KBL NUC). Since the actual performance
can never exceed 1 core turbo frequency from MSR TURBO_RATIO_LIMIT, we
use this as a bound check.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently, intel_pstate doesn't register if _PSS is not present on
HP Proliant systems, because it expects the firmware to take over
CPU performance scaling in that case. However, if ACPI PCCH is
present, the firmware expects the kernel to use it for CPU
performance scaling and the pcc-cpufreq driver is loaded for that.
Unfortunately, the firmware interface used by that driver is not
scalable for fundamental reasons, so pcc-cpufreq is way suboptimal
on systems with more than just a few CPUs. In fact, it is better to
avoid using it at all.
For this reason, modify intel_pstate to look for ACPI PCCH if _PSS
is not present and register if it is there. Also prevent the
pcc-cpufreq driver from trying to initialize itself if intel_pstate
has been registered already.
Fixes: fbbcdc0744 (intel_pstate: skip the driver if ACPI has power mgmt option)
Reported-by: Andreas Herrmann <aherrmann@suse.com>
Reviewed-by: Andreas Herrmann <aherrmann@suse.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Tested-by: Andreas Herrmann <aherrmann@suse.com>
Cc: 4.16+ <stable@vger.kernel.org> # 4.16+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
match_string() returns the index of an array for a matching string,
which can be used instead of open coded variant.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Yisheng Xie <xieyisheng1@huawei.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When scaling max/min settings are changed, internally they are converted
to a ratio using the max turbo 1 core turbo frequency. This works fine
when 1 core max is same irrespective of the core. But under Turbo 3.0,
this will not be the case. For example:
Core 0: max turbo pstate: 43 (4.3GHz)
Core 1: max turbo pstate: 45 (4.5GHz)
In this case 1 core turbo ratio will be maximum of all, so it will be
45 (4.5GHz). Suppose scaling max is set to 4GHz (ratio 40) for all cores
,then on core one it will be
= max_state * policy->max / max_freq;
= 43 * (4000000/4500000) = 38 (3.8GHz)
= 38
which is 200MHz less than the desired.
On core2, it will be correctly set to ratio 40 (4GHz). Same holds true
for scaling min frequency limit. So this requires usage of correct turbo
max frequency for core one, which in this case is 4.3GHz. So we need to
adjust per CPU cpu->pstate.turbo_freq using the maximum HWP ratio of that
core.
This change uses the HWP capability of a core to adjust max turbo
frequency. But since Broadwell HWP doesn't use ratios in the HWP
capabilities, we have to use legacy max 1 core turbo ratio. This is not
a problem as the HWP capabilities don't differ among cores in Broadwell.
We need to check for non Broadwell CPU model for applying this change,
though.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: 4.6+ <stable@vger.kernel.org> # 4.6+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- Revert a recent PM core change that attempted to fix an issue
related to device links, but introduced a regression (Rafael
Wysocki).
- Fix build when the recently added cpufreq driver for Kryo
processors is selected by making it possible to build that
driver as a module (Arnd Bergmann).
- Fix the long idle detection mechanism in the out-of-band
(ondemand and conservative) cpufreq governors (Chen Yu).
- Add support for devices in multiple power domains to the
generic power domains (genpd) framework (Ulf Hansson).
- Add support for iowait boosting on systems with hardware-managed
P-states (HWP) enabled to the intel_pstate driver and make it use
that feature on systems with Skylake Xeon processors as it is
reported to improve performance significantly on those systems
(Srinivas Pandruvada).
- Fix and update the acpi_cpufreq, ti-cpufreq and imx6q cpufreq
drivers (Colin Ian King, Suman Anna, Sébastien Szymanski).
- Change the behavior of the wakeup_count device attribute in
sysfs to expose the number of events when the device might have
aborted system suspend in progress (Ravi Chandra Sadineni).
- Fix two minor issues in the cpupower utility (Abhishek Goel,
Colin Ian King).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=VROk
-----END PGP SIGNATURE-----
Merge tag 'pm-4.18-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management updates from Rafael Wysocki:
"These revert a recent PM core change that introduced a regression, fix
the build when the recently added Kryo cpufreq driver is selected, add
support for devices attached to multiple power domains to the generic
power domains (genpd) framework, add support for iowait boosting on
systens with hardware-managed P-states (HWP) enabled to the
intel_pstate driver, modify the behavior of the wakeup_count device
attribute in sysfs, fix a few issues and clean up some ugliness,
mostly in cpufreq (core and drivers) and in the cpupower utility.
Specifics:
- Revert a recent PM core change that attempted to fix an issue
related to device links, but introduced a regression (Rafael
Wysocki)
- Fix build when the recently added cpufreq driver for Kryo
processors is selected by making it possible to build that driver
as a module (Arnd Bergmann)
- Fix the long idle detection mechanism in the out-of-band (ondemand
and conservative) cpufreq governors (Chen Yu)
- Add support for devices in multiple power domains to the generic
power domains (genpd) framework (Ulf Hansson)
- Add support for iowait boosting on systems with hardware-managed
P-states (HWP) enabled to the intel_pstate driver and make it use
that feature on systems with Skylake Xeon processors as it is
reported to improve performance significantly on those systems
(Srinivas Pandruvada)
- Fix and update the acpi_cpufreq, ti-cpufreq and imx6q cpufreq
drivers (Colin Ian King, Suman Anna, Sébastien Szymanski)
- Change the behavior of the wakeup_count device attribute in sysfs
to expose the number of events when the device might have aborted
system suspend in progress (Ravi Chandra Sadineni)
- Fix two minor issues in the cpupower utility (Abhishek Goel, Colin
Ian King)"
* tag 'pm-4.18-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
Revert "PM / runtime: Fixup reference counting of device link suppliers at probe"
cpufreq: imx6q: check speed grades for i.MX6ULL
cpufreq: governors: Fix long idle detection logic in load calculation
cpufreq: intel_pstate: enable boost for Skylake Xeon
PM / wakeup: Export wakeup_count instead of event_count via sysfs
PM / Domains: Add dev_pm_domain_attach_by_id() to manage multi PM domains
PM / Domains: Add support for multi PM domains per device to genpd
PM / Domains: Split genpd_dev_pm_attach()
PM / Domains: Don't attach devices in genpd with multi PM domains
PM / Domains: dt: Allow power-domain property to be a list of specifiers
cpufreq: intel_pstate: New sysfs entry to control HWP boost
cpufreq: intel_pstate: HWP boost performance on IO wakeup
cpufreq: intel_pstate: Add HWP boost utility and sched util hooks
cpufreq: ti-cpufreq: Use devres managed API in probe()
cpufreq: ti-cpufreq: Fix an incorrect error return value
cpufreq: ACPI: make function acpi_cpufreq_fast_switch() static
cpufreq: kryo: allow building as a loadable module
cpupower : Fix header name to read idle state name
cpupower: fix spelling mistake: "logilename" -> "logfilename"
Enable HWP boost on Skylake server and workstations.
Reported-by: Mel Gorman <mgorman@techsingularity.net>
Tested-by: Giovanni Gherdovich <ggherdovich@suse.cz>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
A new attribute is added to intel_pstate sysfs to enable/disable
HWP dynamic performance boost.
Reported-by: Mel Gorman <mgorman@techsingularity.net>
Tested-by: Giovanni Gherdovich <ggherdovich@suse.cz>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This change uses SCHED_CPUFREQ_IOWAIT flag to boost HWP performance.
Since SCHED_CPUFREQ_IOWAIT flag is set frequently, we don't start
boosting steps unless we see two consecutive flags in two ticks. This
avoids boosting due to IO because of regular system activities.
To avoid synchronization issues, the actual processing of the flag is
done on the local CPU callback.
Reported-by: Mel Gorman <mgorman@techsingularity.net>
Tested-by: Giovanni Gherdovich <ggherdovich@suse.cz>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Added two utility functions to HWP boost up gradually and boost down to
the default cached HWP request values.
Boost up:
Boost up updates HWP request minimum value in steps. This minimum value
can reach upto at HWP request maximum values depends on how frequently,
this boost up function is called. At max, boost up will take three steps
to reach the maximum, depending on the current HWP request levels and HWP
capabilities. For example, if the current settings are:
If P0 (Turbo max) = P1 (Guaranteed max) = min
No boost at all.
If P0 (Turbo max) > P1 (Guaranteed max) = min
Should result in one level boost only for P0.
If P0 (Turbo max) = P1 (Guaranteed max) > min
Should result in two level boost:
(min + p1)/2 and P1.
If P0 (Turbo max) > P1 (Guaranteed max) > min
Should result in three level boost:
(min + p1)/2, P1 and P0.
We don't set any level between P0 and P1 as there is no guarantee that
they will be honored.
Boost down:
After the system is idle for hold time of 3ms, the HWP request is reset
to the default value from HWP init or user modified one via sysfs.
Caching of HWP Request and Capabilities
Store the HWP request value last set using MSR_HWP_REQUEST and read
MSR_HWP_CAPABILITIES. This avoid reading of MSRs in the boost utility
functions.
These boost utility functions calculated limits are based on the latest
HWP request value, which can be modified by setpolicy() callback. So if
user space modifies the minimum perf value, that will be accounted for
every time the boost up is called. There will be case when there can be
contention with the user modified minimum perf, in that case user value
will gain precedence. For example just before HWP_REQUEST MSR is updated
from setpolicy() callback, the boost up function is called via scheduler
tick callback. Here the cached MSR value is already the latest and limits
are updated based on the latest user limits, but on return the MSR write
callback called from setpolicy() callback will update the HWP_REQUEST
value. This will be used till next time the boost up function is called.
In addition add a variable to control HWP dynamic boosting. When HWP
dynamic boost is active then set the HWP specific update util hook. The
contents in the utility hooks will be filled in the subsequent patches.
Reported-by: Mel Gorman <mgorman@techsingularity.net>
Tested-by: Giovanni Gherdovich <ggherdovich@suse.cz>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Chen Yu