[ Upstream commit e98e2367dfb4b6d7a80c8ce795c644124eff5f36 ]
The Samsung PMIC datasheets describe the interrupt line as active low
with a requirement of acknowledge from the CPU. Without specifying the
interrupt type in Devicetree, kernel might apply some fixed
configuration, not necessarily working for this hardware.
Fixes: 01e5d23521 ("arm64: dts: exynos: Add dts file for Exynos5433-based TM2 board")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20201210212903.216728-7-krzk@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
Add nodes for GPU (Mali T760) to Exynos5433. Missing element is the
cooling device. Not tested on HW.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
GSCALER should be feed with clock at certain rates. Configure it on
Exynos5433 based TM2 board.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
TM2(e) boards have a Broadcom Bluetooth chip connected to 3rd UART port.
Add a device tree node describing it and its resources (control GPIO lines
and clock).
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
MMC host controller bindings and MMC core defines card detect pin as
active low. Therefore there is no point to invert it twice.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
OF graph describes USB data lanes between USB-PHY and respective MUIC.
Since graph is present and DWC driver can use it to get extcon, obsolete
extcon property can be removed.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
OF graph describes MHL data lanes between MHL and respective USB
connector.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Since USB connector bindings are available we can describe it on TM2(e).
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This patch updates the sound node of the exynos5433-tm2 board
and adds clock tree configuration in order to support HDMI sound.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
sii8620 supports 1 MHz clock, it allows faster transmissions and according
to extensive tests allows to mitigate some obscure bugs in I2C client
logic of the chip.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Add device tree node with S3FWRN5 NFC chip to TM2(e) boards. The chip is
connected through HS-I2C bus #4.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
[mszyprow: rebased onto v4.15-rc1, moved node to exynos5433-tm2-common.dtsi,
rephrased commit message]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
As usual, device tree updates is the bulk of our material in this merge
window. This time around, 559 patches affecting both 32- and 64-bit
platforms.
Changes are too many to list individually, but some of the larger ones:
New platform/SoC support:
- Automotive:
+ Renesas R-Car D3 (R8A77995)
+ TI DT76x
+ MediaTek mt2712e
- Communication-oriented:
+ Qualcomm IPQ8074
+ Broadcom Stingray
+ Marvell Armada 8080
- Set top box:
+ Uniphier PXs3
Besides some vendor reference boards for the SoC above, there are also several
new boards/machines:
- TI AM335x Moxa UC-8100-ME-T open platform
- TI AM57xx Beaglebone X15 Rev C
- Microchip/Atmel sama5d27 SoM1 EK
- Broadcom Raspberry Pi Zero W
- Gemini-based D-Link DIR-685 router
- Freescale i.MX6:
+ Toradex Apalis module + Apalis and Ixora carrier boards
+ Engicam GEAM6UL Starter Kit
- Freescale i.MX53-based Beckhoff CX9020 Embedded PC
- Mediatek mt7623-based BananaPi R2
- Several Allwinner-based single-board computers:
+ Cubietruck plus
+ Bananapi M3, M2M and M64
+ NanoPi A64
+ A64-OLinuXino
+ Pine64
- Rockchip RK3328 Pine64/Rock64 board support
- Rockchip RK3399 boards:
+ RK3399 Sapphire module on Excavator carrier (RK3399 reference design)
+ Theobroma Systems RK3399-Q7 SoM
- ZTE ZX296718 PCBOX Board
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJZtdtjAAoJEIwa5zzehBx3PzgP/iCQyUk5wklG9E5YNl8a9m/o
djBkelabTm52s5ZTu6Awsq5rx8jUMqcb0vo+9v9yPWFG6On2oTZyZ/rE1Wbj3+gG
+ENVyRgxmzYDTXqQLiu1UOV9wSA0gHwQCRZvE7i32NNfLu+tAsvu9e/AuznQ1xhR
4G7dGCRRlRkZkrVKrJ7JjklmW578pFQkZLmz8K2nWqwh1tKpK3fY19SrwUKx+YCR
tnMPYAPjB5zxR9tfcDS4FUKdiC7dMiMzZNGiYl5a26X6wsNR7xYtNzFMaGZn1ecG
PwOS+DAnj8J+AfpQBLWu9xytHbJdqITRuNcF+OXNVW9TKmb0syf7VgRUDkhjIMxP
aGZc4Q6PwgTRwnX+w6fTzJTyk+uXtieCicZaaZ1jlgcQq0pfbzJ1vZMpq4aoVlxU
mS84i1bd8AiavmHuyIRNB3/T4aAsVhTUIBndXluKV8yWroXhAukfI1YmGr1Eux7C
fy5pPeDqk9lXR3bqIhfnaLoVsApEXTOWMC8X48vwfaQHiCGR9JJwpfsGcaNi1bri
Col1qRzkXWGA6KqTWtpo+o12rYuMGc0mpZTCmejKuBoxMXOU+wLyJYgaxa7pyesX
S5rLaIe2l9ppXHjjEERp7AzczzLS5W20Tez5vYnZAQb1dYuJzwXwiATt8NT+XG3V
Wu92UwUfjxYk8vGz48ph
=R45j
-----END PGP SIGNATURE-----
Merge tag 'armsoc-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM/arm64 Devicetree updates from Olof Johansson:
"As usual, device tree updates is the bulk of our material in this
merge window. This time around, 559 patches affecting both 32- and
64-bit platforms.
Changes are too many to list individually, but some of the larger
ones:
New platform/SoC support:
- Automotive:
+ Renesas R-Car D3 (R8A77995)
+ TI DT76x
+ MediaTek mt2712e
- Communication-oriented:
+ Qualcomm IPQ8074
+ Broadcom Stingray
+ Marvell Armada 8080
- Set top box:
+ Uniphier PXs3
Besides some vendor reference boards for the SoC above, there are also
several new boards/machines:
- TI AM335x Moxa UC-8100-ME-T open platform
- TI AM57xx Beaglebone X15 Rev C
- Microchip/Atmel sama5d27 SoM1 EK
- Broadcom Raspberry Pi Zero W
- Gemini-based D-Link DIR-685 router
- Freescale i.MX6:
+ Toradex Apalis module + Apalis and Ixora carrier boards
+ Engicam GEAM6UL Starter Kit
- Freescale i.MX53-based Beckhoff CX9020 Embedded PC
- Mediatek mt7623-based BananaPi R2
- Several Allwinner-based single-board computers:
+ Cubietruck plus
+ Bananapi M3, M2M and M64
+ NanoPi A64
+ A64-OLinuXino
+ Pine64
- Rockchip RK3328 Pine64/Rock64 board support
- Rockchip RK3399 boards:
+ RK3399 Sapphire module on Excavator carrier (RK3399 reference design)
+ Theobroma Systems RK3399-Q7 SoM
- ZTE ZX296718 PCBOX Board"
* tag 'armsoc-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (559 commits)
ARM: dts: at91: at91sam9g45: add AC97
arm64: dts: marvell: mcbin: enable more networking ports
arm64: dts: marvell: add a reference to the sysctrl syscon in the ppv2 node
arm64: dts: marvell: add TX interrupts for PPv2.2
arm64: dts: uniphier: add PXs3 SoC support
ARM: dts: uniphier: add pinctrl groups of ethernet phy mode
ARM: dts: uniphier: fix size of sdctrl nodes
ARM: dts: uniphier: add AIDET nodes
arm64: dts: uniphier: fix size of sdctrl node
arm64: dts: uniphier: add AIDET nodes
Revert "ARM: dts: sun8i: h3: Enable dwmac-sun8i on the Beelink X2"
arm64: dts: uniphier: add reset controller node of analog amplifier
arm64: dts: marvell: add Device Tree files for Armada-8KP
arm64: dts: rockchip: add Haikou baseboard with RK3399-Q7 SoM
arm64: dts: rockchip: add RK3399-Q7 (Puma) SoM
dt-bindings: add rk3399-q7 SoM
ARM: dts: rockchip: enable usb for rv1108-evb
ARM: dts: rockchip: add usb nodes for rv1108 SoCs
dt-bindings: update grf-binding for rv1108 SoCs
ARM: dts: aspeed-g4: fix AHB window size of the SMC controllers
...
Since i80/command mode is determined in runtime by propagating info
from panel this property can be removed.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
dwmmc driver deprecated num-slots and plan to get rid
of it finally. Just move a step to cleanup it from DT.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Since commit 9840354ff4 ("usb: dwc3: Add dual-role support") dwc3
node requires extcon property to be initialized as OTG mode and it
supports dual-role mode operation.
Signed-off-by: Dongwoo Lee <dwoo08.lee@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Exynos5433 has two usb 3.0 controllers: usbhost and usbdrd. usbhost
is host-only controller whereas usbdrd supports both peripheral and
host mode. "drd" means dual-role device, so usbhost cannot be labeled
with the name containing "drd". However, the label usbdrd_dwc3_0 was
used for usbhost's dwc3 node. It seems it obviously fault because TM2
and TM2E doesn't use usbhost but dr_mode property is assigned to it.
This patch assigns the proper label for two dwc3 nodes.
Signed-off-by: Dongwoo Lee <dwoo08.lee@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The OF graph is not needed because the panel is a child of dsi. Remove
the ports node in DSI node.
Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Compiling the DT file with W=1, DTC warns like follows:
Warning (unit_address_vs_reg): Node /opp_table0/opp@1000000000 has a
unit name, but no reg property
Fix this by replacing '@' with '-' as the OPP nodes will never have a
"reg" property.
Reported-by: Krzysztof Kozlowski <krzk@kernel.org>
Reported-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
[k.kozlowski: Split patch per ARM and ARM64]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Add initial clock configuration for display subsystem for Exynos5433
based TM2/TM2e boards in device tree in order to avoid dependency on the
configuration left by the bootloader. This initial configuration is also
needed to ensure that display subsystem is operational if display power
domain gets turned off before clock controller is probed and the inital
clock configuration left by the bootloader saved.
TM2 and TM2e uses different rate for DISP PLL clock, but for better
maintainability all 'assigned-clocks-*' properties for DISP CMU are
defines in each board dts instead of redefining the rates property.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
LDO7 regulator beside DSI and HDMI provides power for core blocks in Exynos
5433 SoC. Disabling it causes serious current leak - about 200mA.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Ultra HD modes requires clock ticking at increased rate.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Currently TM2E dts includes TM2 but there are some differences
between the two boards and TM2 has some properties that TM2E
doesn't have.
That's why it's important to keep the two dts files independent
and put all the commonalities in a tm2-common.dtsi file.
At the current status the only two differences between the two
dts files (besides the board name) are ldo31 and ldo38.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Krzysztof Kozlowski