[ Upstream commit 93f2a11580a9732c1d90f9e01a7e9facc825658f ]
The GCC_LPASS_Q6_AXI_CLK and GCC_LPASS_SWAY_CLK clocks may not be
touched on a typical UEFI based SDM845 device, but when the kernel is
built with CONFIG_SDM_LPASSCC_845 this happens, unless they are marked
as protected-clocks in the DT.
This was done for the MTP and the Pocophone, but not for DB845c and the
Lenovo Yoga C630 - causing these to fail to boot if the LPASS clock
controller is enabled (which it typically isn't).
Tested-by: Vinod Koul <vkoul@kernel.org> #on db845c
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20201222001103.3112306-1-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a9164910c5ceed63551280a4a0b85d37ac2b19a5 ]
Indicated by AML code in ACPI table, the touchpad in-use could be found
on two possible slave addresses on &i2c3, i.e. hid@15 and hid@2c. And
which one is in-use can be determined by reading another address on the
I2C bus. Unfortunately, for DT boot, there is currently no support in
firmware to make this check and patch DT accordingly. This results in
a non-functional touchpad on those C630 devices with hid@2c.
As i2c-hid driver will stop probing the device if there is nothing on
the slave address, we can actually keep both devices enabled in DT, and
i2c-hid driver will only probe the existing one. The only problem is
that we cannot set up pinctrl in both device nodes, as two devices with
the same pinctrl will cause pin conflict that makes the second device
fail to probe. Let's move the pinctrl state up to parent node to solve
this problem. As the pinctrl state of parent node is already defined in
sdm845.dtsi, it ends up with overwriting pinctrl-0 with i2c3_hid_active
state added in there.
Fixes: 11d0e4f28156 ("arm64: dts: qcom: c630: Polish i2c-hid devices")
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Link: https://lore.kernel.org/r/20210102045940.26874-1-shawn.guo@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 11d0e4f281565ef757479764ce7fd8d35eeb01b0 ]
The numbering of the i2c busses differs from ACPI and a number of typos
was made in the original patch. Further more the irq flags for the
various resources was not correct and i2c3 only has one of the two
client devices active in any one device.
Also label the various devices, for easier comparison with the ACPI
tables.
Tested-by: Steev Klimaszewski <steev@kali.org>
Fixes: 44acee2078 ("arm64: dts: qcom: Add Lenovo Yoga C630")
Link: https://lore.kernel.org/r/20201130165924.319708-1-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
The Lenovo Yoga C630 is built on the SDM850 from Qualcomm, but this seem
to be similar enough to the SDM845 that we can reuse the sdm845.dtsi.
Supported by this patch is: keyboard, battery monitoring, UFS storage,
USB host and Bluetooth.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
[Lee] Reorder, change licence, remove non-upstream device node
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
