commit cfb5d65f25959f724081bae8445a0241db606af6 upstream.
The L3 interconnect's memory map is from 0x0 to
0xffffffff. Out of this, System memory (SDRAM) can be
accessed from 0x80000000 to 0xffffffff (2GB)
DRA7 does support 4GB of SDRAM but upper 2GB can only be
accessed by the MPU subsystem.
Add the dma-ranges property to reflect the physical address limit
of the L3 bus.
Issues ere observed only with SATA on DRA7-EVM with 4GB RAM
and CONFIG_ARM_LPAE enabled. This is because the controller
supports 64-bit DMA and its driver sets the dma_mask to 64-bit
thus resulting in DMA accesses beyond L3 limit of 2G.
Setting the correct bus_dma_limit fixes the issue.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Cc: stable@kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 27f13774654ea6bd0b6fc9b97cce8d19e5735661 ]
'dma-ranges' in a PCI bridge node does correctly set dma masks for PCI
devices not described in the DT. Certain DRA7 platforms (e.g., DRA76)
has RAM above 32-bit boundary (accessible with LPAE config) though the
PCIe bridge will be able to access only 32-bits. Add 'dma-ranges'
property in PCIe RC DT nodes to indicate the host bridge can access
only 32 bits.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b830526f30 ]
Add ti,syscon-unaligned-access property to PCIe RC nodes to set
appropriate bits in CTRL_CORE_SMA_SW_7 register to enable workaround for
errata i870.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cc893871f0 ]
dtc has new checks for I2C and SPI buses. Fix the warnings in node names
and unit-addresses.
arch/arm/boot/dts/am437x-idk-evm.dtb: Warning (spi_bus_bridge): /ocp@44000000/qspi@47900000: node name for SPI buses should be 'spi'
arch/arm/boot/dts/am437x-sk-evm.dtb: Warning (spi_bus_bridge): /ocp@44000000/qspi@47900000: node name for SPI buses should be 'spi'
arch/arm/boot/dts/am43x-epos-evm.dtb: Warning (spi_bus_bridge): /ocp@44000000/qspi@47900000: node name for SPI buses should be 'spi'
arch/arm/boot/dts/omap3-n9.dtb: Warning (i2c_bus_reg): /ocp@68000000/i2c@48060000/ak8975@0f: I2C bus unit address format error, expected "f"
arch/arm/boot/dts/am335x-osd3358-sm-red.dtb: Warning (i2c_bus_reg): /ocp/i2c@44e0b000/pressure@78: I2C bus unit address format error, expected "76"
arch/arm/boot/dts/am335x-boneblack.dtb: Warning (i2c_bus_reg): /ocp/i2c@44e0b000/tda19988: I2C bus unit address format error, expected "70"
arch/arm/boot/dts/am335x-boneblack-wireless.dtb: Warning (i2c_bus_reg): /ocp/i2c@44e0b000/tda19988: I2C bus unit address format error, expected "70"
arch/arm/boot/dts/am335x-sancloud-bbe.dtb: Warning (i2c_bus_reg): /ocp/i2c@44e0b000/tda19988: I2C bus unit address format error, expected "70"
arch/arm/boot/dts/am571x-idk.dtb: Warning (spi_bus_bridge): /ocp/qspi@4b300000: node name for SPI buses should be 'spi'
arch/arm/boot/dts/am572x-idk.dtb: Warning (spi_bus_bridge): /ocp/qspi@4b300000: node name for SPI buses should be 'spi'
arch/arm/boot/dts/am574x-idk.dtb: Warning (spi_bus_bridge): /ocp/qspi@4b300000: node name for SPI buses should be 'spi'
arch/arm/boot/dts/am57xx-cl-som-am57x.dtb: Warning (spi_bus_bridge): /ocp/qspi@4b300000: node name for SPI buses should be 'spi'
arch/arm/boot/dts/am57xx-sbc-am57x.dtb: Warning (spi_bus_bridge): /ocp/qspi@4b300000: node name for SPI buses should be 'spi'
arch/arm/boot/dts/dra72-evm.dtb: Warning (spi_bus_bridge): /ocp/qspi@4b300000: node name for SPI buses should be 'spi'
arch/arm/boot/dts/dra72-evm-revc.dtb: Warning (spi_bus_bridge): /ocp/qspi@4b300000: node name for SPI buses should be 'spi'
arch/arm/boot/dts/dra76-evm.dtb: Warning (spi_bus_bridge): /ocp/qspi@4b300000: node name for SPI buses should be 'spi'
arch/arm/boot/dts/dra7-evm.dtb: Warning (spi_bus_bridge): /ocp/qspi@4b300000: node name for SPI buses should be 'spi'
arch/arm/boot/dts/am335x-pdu001.dtb: Warning (spi_bus_reg): /ocp/spi@481a0000/cfaf240320a032t: SPI bus unit address format error, expected "0"
arch/arm/boot/dts/keystone-k2g-evm.dtb: Warning (spi_bus_bridge): /soc@0/qspi@2940000: node name for SPI buses should be 'spi'
arch/arm/boot/dts/keystone-k2g-ice.dtb: Warning (spi_bus_bridge): /soc@0/qspi@2940000: node name for SPI buses should be 'spi'
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Santosh Shilimkar <ssantosh@kernel.org>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
[tony@atomide.com: fixed mode to 644 for am335x-osd3358-sm-red.dts while at it]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 6d0af44a82 upstream.
Bit positions of PCIE_SS1_AXI2OCP_LEGACY_MODE_ENABLE and
PCIE_SS1_AXI2OCP_LEGACY_MODE_ENABLE in CTRL_CORE_SMA_SW_7 are
incorrectly documented in the TRM. In fact, the bit positions are
swapped. Update the DT bindings for PCIe EP to reflect the same.
Fixes: d23f3839fe ("ARM: dts: DRA7: Add pcie1 dt node for EP mode")
Cc: stable@vger.kernel.org
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Business as usual -- the bulk of our changes are to devicetree files
with new hardware support, new SoCs and platforms, and new board types.
New SoCs/platforms:
- Raspberry Pi Compute Module (CM1) and IO board
- i.MX6SSL from NXP
- Renesas RZ/N1D SoC (R9A06G032), Dual Cortex-A7 with Ethernet, CAN and
PLC interfaces
- TI AM654 SoC, Quad Cortex-A53, safety subsystem with Cortex-R5
controllers, communication and PRU subsystem and lots of other
interfaces (PCIe, USB3, etc).
New boards and systems:
- Several Atmel at91-based boards from Laird
- Marvell Armada388-based Helios4 board from SolidRun
- Samsung Aires-based phones (s5pv210)
- Allwinner A64-based Pinebook laptop
In addition to the above, there's the usual amount of new devices
described on existing platforms, fixes and tweaks and new minor variants
of boards/platforms.
-----BEGIN PGP SIGNATURE-----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=J0qC
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM device-tree updates from Olof Johansson:
"Business as usual -- the bulk of our changes are to devicetree files
with new hardware support, new SoCs and platforms, and new board
types.
New SoCs/platforms:
- Raspberry Pi Compute Module (CM1) and IO board
- i.MX6SSL from NXP
- Renesas RZ/N1D SoC (R9A06G032), Dual Cortex-A7 with Ethernet, CAN
and PLC interfaces
- TI AM654 SoC, Quad Cortex-A53, safety subsystem with Cortex-R5
controllers, communication and PRU subsystem and lots of other
interfaces (PCIe, USB3, etc).
New boards and systems:
- Several Atmel at91-based boards from Laird
- Marvell Armada388-based Helios4 board from SolidRun
- Samsung Aires-based phones (s5pv210)
- Allwinner A64-based Pinebook laptop
In addition to the above, there's the usual amount of new devices
described on existing platforms, fixes and tweaks and new minor
variants of boards/platforms"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (478 commits)
arm64: dts: sdm845: Add tsens nodes
arm64: dts: msm8996: thermal: Initialise via DT and add second controller
arm64: dts: sprd: Add one suspend timer
arm64: dts: sprd: Add SC27XX ADC device
arm64: dts: sprd: Add SC27XX eFuse device
arm64: dts: sprd: Add SC27XX vibrator device
arm64: dts: sprd: Add SC27XX breathing light controller device
arm64: dts: meson-axg: add spdif-dit codec
arm64: dts: meson-axg: add lineout codec
arm64: dts: meson-axg: add linein codec
arm64: dts: meson-axg: add tdm interfaces
arm64: dts: meson-axg: add tdmout formatters
arm64: dts: meson-axg: add tdmin formatters
arm64: dts: meson-axg: add spdifout
arm64: dts: rockchip: add led support for Firefly-RK3399
arm64: dts: rockchip: remove deprecated Type-C PHY properties on rk3399
arm64: dts: rockchip: add power button support for Firefly-RK3399
ARM: dts: aspeed: Add coprocessor interrupt controller
arm64: dts: meson-axg: add audio arb reset controller
arm64: dts: meson-axg: add usb power regulator
...
Disable the metastability workaround for USB2. The original
patch disabled the workaround on the wrong USB port.
Fixes: b8c9c6fa20 ("ARM: dts: dra7: Disable USB metastability workaround for USB2")
Cc: <stable@vger.kernel.org> [4.16+]
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix the DT node addresses to match the reg property addresses,
which were verified to match the TRM:
http://www.ti.com/lit/pdf/sprui30
Cc: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
While the supported UHS mode can be obtained from CAPA2
register, SD Host Controller Standard Specification
doesn't define bits for MMC's HS200 and DDR mode capability.
Add properties to indicate MMC HS200 and DDR speed mode capability in
dt node.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use sdhci-omap programming model based on the generic sdhci
library for programming the eMMC/SD/SDIO controller.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The "cooling-min-level" and "cooling-max-level" properties are not
parsed by any part of the kernel currently and the max cooling state of
a CPU cooling device is found by referring to the cpufreq table instead.
Remove the unused properties from the CPU nodes.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
A number of new drivers get added this time, along with many low-priority
bugfixes. The most interesting changes by subsystem are:
bus drivers:
- Updates to the Broadcom bus interface driver to support newer SoC types
- The TI OMAP sysc driver now supports updated DT bindings
memory controllers:
- A new driver for Tegra186 gets added
- A new driver for the ti-emif sram, to allow relocating
suspend/resume handlers there
SoC specific:
- A new driver for Qualcomm QMI, the interface to the modem on MSM SoCs
- A new driver for power domains on the actions S700 SoC
- A driver for the Xilinx Zynq VCU logicoreIP
reset controllers:
- A new driver for Amlogic Meson-AGX
- various bug fixes
tee subsystem:
- A new user interface got added to enable asynchronous communication
with the TEE supplicant.
- A new method of using user space memory for communication with
the TEE is added
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=yz0k
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"A number of new drivers get added this time, along with many
low-priority bugfixes. The most interesting changes by subsystem are:
bus drivers:
- Updates to the Broadcom bus interface driver to support newer SoC
types
- The TI OMAP sysc driver now supports updated DT bindings
memory controllers:
- A new driver for Tegra186 gets added
- A new driver for the ti-emif sram, to allow relocating
suspend/resume handlers there
SoC specific:
- A new driver for Qualcomm QMI, the interface to the modem on MSM
SoCs
- A new driver for power domains on the actions S700 SoC
- A driver for the Xilinx Zynq VCU logicoreIP
reset controllers:
- A new driver for Amlogic Meson-AGX
- various bug fixes
tee subsystem:
- A new user interface got added to enable asynchronous communication
with the TEE supplicant.
- A new method of using user space memory for communication with the
TEE is added"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (84 commits)
of: platform: fix OF node refcount leak
soc: fsl: guts: Add a NULL check for devm_kasprintf()
bus: ti-sysc: Fix smartreflex sysc mask
psci: add CPU_IDLE dependency
soc: xilinx: Fix Kconfig alignment
soc: xilinx: xlnx_vcu: Use bitwise & rather than logical && on clkoutdiv
soc: xilinx: xlnx_vcu: Depends on HAS_IOMEM for xlnx_vcu
soc: bcm: brcmstb: Be multi-platform compatible
soc: brcmstb: biuctrl: exit without warning on non brcmstb platforms
Revert "soc: brcmstb: Only register SoC device on STB platforms"
bus: omap: add MODULE_LICENSE tags
soc: brcmstb: Only register SoC device on STB platforms
tee: shm: Potential NULL dereference calling tee_shm_register()
soc: xilinx: xlnx_vcu: Add Xilinx ZYNQMP VCU logicoreIP init driver
dt-bindings: soc: xilinx: Add DT bindings to xlnx_vcu driver
soc: xilinx: Create folder structure for soc specific drivers
of: platform: populate /firmware/ node from of_platform_default_populate_init()
soc: samsung: Add SPDX license identifiers
soc: qcom: smp2p: Use common error handling code in qcom_smp2p_probe()
tee: shm: don't put_page on null shm->pages
...
For now, we need to rely on dts alias for n900 lcd and tvout order
to prevent occasional blank lcd. And we need to reduce the shut down
temperature for dra7 for non-cpu thermal cases.
And looks like we're missing the n9 volume key mappings and there is
active work going happening for n9 at least for postmarketos. So let's
make sure the keys can be actually used as they are the only buttons
on n9 in addition to the power key.
-----BEGIN PGP SIGNATURE-----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=M8S+
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.16/dt-pt3-signed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Pull "dts fixes for omaps for v4.16 merge window" from Tony Lindgren:
Few omap dts fixes and n9 volume keys update for v4.16 merge window
For now, we need to rely on dts alias for n900 lcd and tvout order
to prevent occasional blank lcd. And we need to reduce the shut down
temperature for dra7 for non-cpu thermal cases.
And looks like we're missing the n9 volume key mappings and there is
active work going happening for n9 at least for postmarketos. So let's
make sure the keys can be actually used as they are the only buttons
on n9 in addition to the power key.
* tag 'omap-for-v4.16/dt-pt3-signed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Nokia N9: add support for up/down keys in the dts
ARM: dts: dra7: Reduce shut down temperature of non-cpu thermal zones
ARM: dts: n900: Add aliases for lcd and tvout displays
Now that we have the dts clocks for the clkctrl clock and the
interconnect binding, we need to update the existing ti-sysc
users according to the binding to make it usable for drivers.
Apologies for not being able to send this earlier but it took
me few revisions to get the smartreflex changes right and
tested with yet to be posted patches to make smartreflex probe
with dts and I wanted to have it sit in next for a while to make
sure we're not introducing regressions for legacy platform data
based booting.
Note that this is based on a merge with commit 20a2742e57
("dt-bindings: ti-sysc: Update binding for timers and capabilities")
to avoid a merge conflict with the binding changes.
-----BEGIN PGP SIGNATURE-----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=oKRR
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.16/dt-clk-dts-signed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Pull "Few omap interconnect dts fixes for v4.16 merge window" from
Tony Lindgren:
Now that we have the dts clocks for the clkctrl clock and the
interconnect binding, we need to update the existing ti-sysc
users according to the binding to make it usable for drivers.
Apologies for not being able to send this earlier but it took
me few revisions to get the smartreflex changes right and
tested with yet to be posted patches to make smartreflex probe
with dts and I wanted to have it sit in next for a while to make
sure we're not introducing regressions for legacy platform data
based booting.
Note that this is based on a merge with commit 20a2742e57
("dt-bindings: ti-sysc: Update binding for timers and capabilities")
to avoid a merge conflict with the binding changes.
* tag 'omap-for-v4.16/dt-clk-dts-signed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Update ti-sysc data for existing users
ARM: dts: Fix smartreflex compatible for omap3 shared mpu-iva instance
dt-bindings: ti-sysc: Update binding for timers and capabilities
On dra7, as per TRM, the HW shutdown (TSHUT) temperature is hardcoded
to 123C and cannot be modified by SW. This means that when the temperature
reaches 123C HW asserts TSHUT output which signals a warm reset.
The reset is held until the temperature goes below the TSHUT low (105C).
While in SW, the thermal driver continuously monitors current temperature
and takes decisions based on whether it reached an alert or a critical point.
The intention of setting a SW critical point is to prevent force reset by HW
and instead do an orderly_poweroff(). But if the SW critical temperature is
greater than or equal to that of HW then it defeats the purpose. To address
this and let SW take action before HW does keep the SW critical temperature
less than HW TSHUT value.
The value for SW critical temperature was chosen as 120C just to ensure
we give SW sometime before HW catches up.
Document reference
SPRUI30C – DRA75x, DRA74x Technical Reference Manual - November 2016
SPRUHZ6H - AM572x Technical Reference Manual - November 2016
Tested on:
DRA75x PG 2.0 Rev H EVM
Signed-off-by: Ravikumar Kattekola <rk@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Let's update the existing users with features and clock data as
specified in the binding. This is currently the smartreflex for most
part, and also few omap4 modules with no child device driver like
mcasp, abe iss and gfx.
Note that we had few mistakes that did not get noticed as we're still
probing the SmartReflex driver with legacy platform data and using
"ti,hwmods" legacy property for ti-sysc driver.
So let's fix the omap4 and dra7 smartreflex registers as there is no
no revision register.
And on omap4, the mcasp module has a revision register according to
the TRM.
And for omap34xx we need a different configuration compared to 36xx.
And the smartreflex on 3517 we've always kept disabled so let's
remove any references to it.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This branch mostly configures more hardware support:
- Clean-up dts files to remove leading 0x and 0s from binding notation
to remove more dtc compiler warnings
- A series of am437x updates for backlight, to fix inverted pad
pull macro, and to configure power management related OPPs
- Configure n950 and droid 4 command mode LCD panels
- Updates to pandora and gta04 LCD panels
- Add support for am574x-idk
- A series of changes to configure more dra7 related PCIe features
- A series of fixes for am335x-boneblue for WLAN, UARTs and CAN
configuration
- A series of changes to configure dra7 OPPs and VDD supplies
-----BEGIN PGP SIGNATURE-----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=G2ZQ
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.16/dt-pt2-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Second set of device tree changes for omaps for v4.16 merge window
This branch mostly configures more hardware support:
- Clean-up dts files to remove leading 0x and 0s from binding notation
to remove more dtc compiler warnings
- A series of am437x updates for backlight, to fix inverted pad
pull macro, and to configure power management related OPPs
- Configure n950 and droid 4 command mode LCD panels
- Updates to pandora and gta04 LCD panels
- Add support for am574x-idk
- A series of changes to configure more dra7 related PCIe features
- A series of fixes for am335x-boneblue for WLAN, UARTs and CAN
configuration
- A series of changes to configure dra7 OPPs and VDD supplies
* tag 'omap-for-v4.16/dt-pt2-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (29 commits)
Revert "ARM: dts: dra7: Add properties to enable PCIe x2 lane mode"
ARM: dts: am572x-idk: Add cpu0 vdd supply
ARM: dts: am571x-idk: Add cpu0 vdd supply
ARM: dts: dra72-evm-tps65917: Add cpu0 vdd supply
ARM: dts: dra7-evm: Add cpu0 vdd supply
ARM: dts: am57xx-beagle-x15-common: Add cpu0 vdd supply
ARM: dts: dra7: Enable 1.5 GHz operation for the CPU
ARM: dts: dra7: Add MPU OPP supply node
ARM: dts: dra7: Add vbb-supply to cpu and additional voltages
ARM: dts: am335x-boneblue: enable can
ARM: dts: am335x-boneblue: enable usarts
ARM: dts: am335x-boneblue: fix wl1835 IRQ pin
ARM: dts: dra7: Remove deprecated PCI compatible string
ARM: dts: dra76-evm: Enable x2 PCIe lanes
ARM: dts: DRA72x: Use PCIe compatible specific to dra72
ARM: dts: DRA74x: Use PCIe compatible specific to dra74
ARM: dts: dra7: Add properties to enable PCIe x2 lane mode
ARM: dts: am57xx: Add support for am574x-idk
ARM: dts: am43x-epos-evm: Hook dcdc2 as the cpu0-supply
ARM: dts: am437x-idk-evm: Disable OPP50 for MPU
...
Signed-off-by: Olof Johansson <olof@lixom.net>
These changes are mostly improvments for various devices.
Note that these are based on my earlier fixes branch
omap-for-v4.15/fixes-dt to avoid a pointless merge conflict
between a fix and removal. The summary of changes is:
- Fix audio codec reset pin for am335x-pepper and n900, this
has been always broken and won't get fixed until the related
driver changes are also merged in for v4.16, so not urgent
- Fix tps65917 powerhold property for dra76-evm
- Changes to logicpd boards to remove MTD partition information
and to add support for omap35xx variants by setting up common
dts files for the logicpd boards
- Disable dra7 USB metastability workaround, this won't do
anything until the related driver changes are also merged
into v4.16, so not urgent
-----BEGIN PGP SIGNATURE-----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=jzFR
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.16/dt-signed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Pull "Dts related changes for omaps for v4.16 merge window" from Tony
Lindgren:
These changes are mostly improvments for various devices.
Note that these are based on my earlier fixes branch
omap-for-v4.15/fixes-dt to avoid a pointless merge conflict
between a fix and removal. The summary of changes is:
- Fix audio codec reset pin for am335x-pepper and n900, this
has been always broken and won't get fixed until the related
driver changes are also merged in for v4.16, so not urgent
- Fix tps65917 powerhold property for dra76-evm
- Changes to logicpd boards to remove MTD partition information
and to add support for omap35xx variants by setting up common
dts files for the logicpd boards
- Disable dra7 USB metastability workaround, this won't do
anything until the related driver changes are also merged
into v4.16, so not urgent
* tag 'omap-for-v4.16/dt-signed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Move move WiFi bindings to logicpd-torpedo-37xx-devkit
ARM: dts: Add minimal support for LogicPD OMAP35xx Torpedo devkit
ARM: dts: Move most of logicpd-torpedo-37xx-devkit to logicpd-torpedo-baseboard
ARM: dts: Add minimal support for LogicPD OMAP35xx SOM-LV devkit
ARM: dts: Move most of logicpd-som-lv-37xx-devkit.dts to logicpd-som-lv-baseboard.dtsi
ARM: dts: dra7: Add missing hdmi audio DMA channel information
ARM: dts: dra7: Disable USB metastability workaround for USB2
ARM: dts: omap3: logicpd kits: Remove partition information
ARM: dts: DRA76-EVM: Set powerhold property for tps65917
ARM: dts: omap3-n900: Fix the audio CODEC's reset pin
ARM: dts: am335x-pepper: Fix the audio CODEC's reset pin
After ti-opp-supply driver is in place to provide AVS Class0 and abb
regulator scaling support let's enable 1.5GHz for the cpu.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the OPP supply node for the MPU voltage rail to provide the
information needed by the ti-opp-supply driver to enable AVS Class 0.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add a vbb-supply phandle to the cpus node and also add an additional
triplet of voltages for each OPP in the operating-points-v2 table to
make use of the multi regulator support in the OPP core and provide the
vbb regulator for use by the ti-opp-supply driver.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Otherwise we cannot use generic OF_DEV_AUXDATA match without listing
all the compatibles separately for OF_DEV_AUXDATA. Let's also update the
binding accordingly.
Let's also fix omap4.dtsi to use "ti,sysc-omap4-sr" compatible as we
have documented in the binding. This was not noticed earlier as we're
still probing SmartReflex driver with platform data.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Since SoC specific compatible strings are used for PCIe in
dra74x.dtsi and dra72x.dtsi, remove the compatible property
from dra7.dtsi which uses the deprecated compatible string.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use dra74 specific compatible string for PCIe while preserving
the older compatible. While at that add a new label for the
2nd instance of pcie.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
ti,syscon-lane-sel and ti,syscon-lane-conf properties specific to enable
PCIe x2 lane mode are added here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Improve the DTS files by removing all the leading "0x" and zeros to fix the
following dtc warnings:
Warning (unit_address_format): Node /XXX unit name should not have
leading "0x"
and
Warning (unit_address_format): Node /XXX unit name should not have
leading 0s
Converted using the following command:
$ find . -type f \( -iname *.dts -o -iname *.dtsi \) -exec \
sed -i -e "s/@\([0-9a-fA-FxX\.;:#]+\)\s*{/@\L\1 {/g" \
-e "s/@0x\(.*\) {/@\1 {/g" -e "s/@0+\(.*\) {/@\1 {/g" {} +^C
For simplicity, two sed expressions were used to solve each warnings
separately.
To make the regex expression more robust a few other issues were resolved,
namely setting unit-address to lower case, and adding a whitespace before
the the opening curly brace:
https://elinux.org/Device_Tree_Linux#Linux_conventions
This will solve as a side effect warning:
Warning (simple_bus_reg): Node /XXX@<UPPER> simple-bus unit address format
error, expected "<lower>"
This is a follow up to commit 4c9847b737 ("dt-bindings: Remove leading
0x from bindings notation")
Reported-by: David Daney <ddaney@caviumnetworks.com>
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The audio DMA request for hdmi is crossbar 76 and we use sDMA
to handle the data transfer.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The metastability workaround causes Erratic errors [1]
on the HighSpeed USB PHY which can cause upto 2 seconds
delay in enumerating to a USB host while in Gadget mode.
Disable the Run/Stop metastability workaround to avoid this
ill effect. We are aware that this opens up the opportunity
for Run/Stop metastability, however this issue has never been
observed in TI releases so we think that Run/Stop metastability
is a lesser evil than the PHY Erratic errors. So disable it.
[1] USB controller trace during gadget enumeration
irq/90-dwc3-969 [000] d... 52.323145: dwc3_event: event
(00000901): Erratic Error [U0]
irq/90-dwc3-969 [000] d... 52.560646: dwc3_event: event
(00000901): Erratic Error [U0]
irq/90-dwc3-969 [000] d... 52.798144: dwc3_event: event
(00000901): Erratic Error [U0]
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@linux/intel.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add clkctrl nodes for DRA7 SoC. These are going to be acting as
replacement for part of the existing clock data and the existing
clkctrl hooks under hwmod data.
This patch also removes any obsolete clock nodes, and reroutes all users
for these to use the new clkctrl clocks instead.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add simple-bus compatibility and ranges properties to cm1, cm2 and prm
nodes. This is done in preparation of adding the support for clkctrl
nodes.
SPLIT: timer1 fck setup
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the functional clock definition for timer1. This is needed so that
the clock rate calculations continue to function properly once dra7
transitions away from hwmod data and towards the clkctrl clocks.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
support for omap35xx-evm, am34xx-epos-evm and dra7:
- A series of changes to fix support for omap35xx-evm
- A series of changes to add earlycon support for n8x0, pandaboard
and omap5 boards
- A series of changes for am43xx-epos-evm pinctrl modes for default
and sleep states
- A series of changes to correct pbias regulator voltage for dra7
from 3V to 3.3V
- Use microchip compatible instead of deprecated mcp compatible for
mcp23017
-----BEGIN PGP SIGNATURE-----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=xWf5
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.15/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Pull "device tree changes for omaps for v4.15 merge window" from Tony Lindgren:
Device tree changes for omaps for v4.15 merge window to improve
support for omap35xx-evm, am34xx-epos-evm and dra7:
- A series of changes to fix support for omap35xx-evm
- A series of changes to add earlycon support for n8x0, pandaboard
and omap5 boards
- A series of changes for am43xx-epos-evm pinctrl modes for default
and sleep states
- A series of changes to correct pbias regulator voltage for dra7
from 3V to 3.3V
- Use microchip compatible instead of deprecated mcp compatible for
mcp23017
* tag 'omap-for-v4.15/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (22 commits)
ARM: dts: omap3: Replace deprecated mcp prefix
ARM: dts: dra7-evm: Move pcie RC node to common file
ARM: dts: omap5: Increase max-voltage of pbias regulator
ARM: dts: dra7: Increase max-voltage of pbias regulator
ARM: dts: am43xx-epos-evm: Add default pinmux for unused pins
ARM: dts: am43xx-epos-evm: Add default and sleep pinmux for usb2_phy1 and usb2_phy2
ARM: dts: am43xx-epos-evm: Add default and sleep pinmux for uart0
ARM: dts: am43xx-epos-evm: Add default and sleep pinmux for matrix_keypad0
ARM: dts: am43xx-epos-evm: Add sleep pinmux for mmc1
ARM: dts: am43xx-epos-evm: Add sleep pinmux for pixcir_ts
ARM: dts: am43xx-epos-evm: Add sleep pinmux for gpmc
ARM: dts: am43xx-epos-evm: Add sleep pinmux for ecap0
ARM: dts: am43xx-epos-evm: Add sleep pinmux for qspi1
ARM: dts: am43xx-epos-evm: Add sleep pinmux for spi0 and spi1
ARM: dts: am43xx: Introduce additional pinmux definitions for DS0
ARM: dts: Configure earlycon for omap5-common
ARM: dts: Configure earlycon for pandaboard
ARM: dts: Configure earlycon for n8x0
ARM: dts: omap3-evm: Add DSS {vdds_dsi,vdda_video}-supply references
ARM: dts: omap3: Add Sharp LS037V7DW01 'envdd' supply
...
As per recent TRM, PBIAS cell on dra7 devices supports
3.3v and not 3.0v as documented earlier.
Update PBIAS regulator max voltage to match this.
Document reference:
SPRUI30C – DRA75x, DRA74x Technical reference manual- November 2016
Tested on:
DRA75x PG 2.0 REV H EVM
Signed-off-by: Ravikumar Kattekola <rk@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The TRM has marked dra7 SmartReflex as reserved and we should not
touch those registers as pointed out by Nishanth Menon <nm@ti.com>.
We do still want to idle the related interconnect target modules on
init though.
Let's do this by only configuring the generic interconnect target modules
and not add the child SmartReflex devices.
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On dra7 we're missing two "ti,hwmods" properties that the SoC
interconnect code needs. For hdq 1-wire, we need to add the
node for that.
Note that this will only show up as a bug with "doesn't have
mpu register target base" boot errors when the legacy platform
data is removed.
Cc: Nishanth Menon <nm@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add pcie1 dt node in order for the controller to operate in
endpoint mode. However since none of the dra7 based boards have
slots configured to operate in endpoint mode, keep EP mode
disabled.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add "max-frequency" property to MMC dt nodes and set the
maximum frequency to 192MHz for MMC1/MMC2, 64MHz for MMC3
and 192MHz for MMC4. pdata quirks must be utilized to
detect presence of rev 1.1/1.0 of silicon and adjust
maximum frequencies as per restrictions documented in i843.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This adds support for am335x-boneblue. The rest of
the changes are for enabling features on various
devices with the git shortlog describing the changes.
-----BEGIN PGP SIGNATURE-----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=u58m
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.13/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Device tree changes for omaps for v4.13 merge window.
This adds support for am335x-boneblue. The rest of
the changes are for enabling features on various
devices with the git shortlog describing the changes.
* tag 'omap-for-v4.13/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
arm: dts: am33xx: Remove redundant interrupt-parent property
ARM: dts: bonegreen-wireless: add WL1835 Bluetooth device node
ARM: dts: AM43XX: Remove min and max voltage values for dcdc3
ARM: dts: Add am335x-boneblue
ARM: dts: twl4030: Add missing madc reference for bci subnode
ARM: dts: am43xx-clocks: Add support for CLKOUT2
ARM: dts: Configure USB host for 37xx-evm
ARM: dts: omap: Add generic compatible string for I2C EEPROM
ARM: dts: Enable earlycon stdout path for LogicPD torpedo
ARM: dts: Enable earlycon stdout path for duovero
arm: dts: boneblack-wireless: add WL1835 Bluetooth device node
ARM: dts: am571x-idk: Enable the system mailboxes 5 and 6
ARM: dts: am572x-idk: Enable the system mailboxes 5 and 6
ARM: dts: omap4-devkit8000: fix gpmc ranges property
ARM: dts: omap3: Remove 'enable-active-low' property
ARM: dts: OMAP5: uevm: add µSD card detect
ARM: dts: omap4-droid4: Add bluetooth
ARM: dts: dra7x-evm: Enable dual-role mode for USB1
ARM: dts: Use - instead of @ for DT OPP entries for TI SoCs
ARM: dts: am335x-phycore-som: fix rv4162 compatible
Signed-off-by: Olof Johansson <olof@lixom.net>
On dra7, as per TRM, the HW shutdown (TSHUT) temperature is hardcoded
to 123C and cannot be modified by SW. This means when the temperature
reaches 123C HW asserts TSHUT output which signals a warm reset.
This reset is held until the temperature goes below the TSHUT low (105C).
While in SW, the thermal driver continuously monitors current temperature
and takes decisions based on whether it reached an alert or a critical point.
The intention of setting a SW critical point is to prevent force reset by HW
and instead do an orderly_poweroff(). But if the SW critical temperature is
greater than or equal to that of HW then it defeats the purpose. To address
this and let SW take action before HW does keep the SW critical temperature
less than HW TSHUT value.
The value for SW critical temperature was chosen as 120C just to ensure
we give SW sometime before HW catches up.
Document reference
SPRUI30C – DRA75x, DRA74x Technical Reference Manual - November 2016
SPRUHZ6H - AM572x Technical Reference Manual - November 2016
Tested on:
DRA75x PG 2.0 Rev H EVM
Signed-off-by: Ravikumar Kattekola <rk@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Compiling the DT file with W=1, DTC warns like follows:
Warning (unit_address_vs_reg): Node /opp_table0/opp@1000000000 has a
unit name, but no reg property
Fix this by replacing '@' with '-' as the OPP nodes will never have a
"reg" property.
Reported-by: Krzysztof Kozlowski <krzk@kernel.org>
Reported-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Device-tree continues to see lots of updates. The majority of patches
here are smaller changes for new hardware on existing platforms, and
there are a few larger changes worth pointing out.
Major new platforms:
- Gemini has been ported to DT, so a handful of "new" platforms moved over
from board files
- Rockchip RK3288 support for Tinkerboard and Phytec phyCORE-RK3288 SoM and RDK
- A bunch of embedded platforms, several Linksys platforms, Synology DS116,
- Motorola Droid4 (really old OMAP-based phone) support is added.
Some refactorings, i.e. Allwinner H3/H5 support is commonalized.
And lots of smaller changes, cleanups, etc. See shortlog for more description
We're adding ability to cross-include DT files between arm and arm64,
by creating appropriate links in the dt-include directory, and using arm/
and arm64/ as include prefixes. This will avoid other local hacks such as
per-file links between the two arch trees (this broke for external mirroring
of DT contents). Now they can just provide their own appropriate dt-include
hierarcy per platform.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=v6w6
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM Device-tree updates from Olof Johansson:
"Device-tree continues to see lots of updates. The majority of patches
here are smaller changes for new hardware on existing platforms, and
there are a few larger changes worth pointing out.
Major new platforms:
- Gemini has been ported to DT, so a handful of "new" platforms moved
over from board files
- Rockchip RK3288 support for Tinkerboard and Phytec phyCORE-RK3288
SoM and RDK
- A bunch of embedded platforms, several Linksys platforms, Synology
DS116,
- Motorola Droid4 (really old OMAP-based phone) support is added.
Some refactorings, i.e. Allwinner H3/H5 support is commonalized.
And lots of smaller changes, cleanups, etc. See shortlog for more
description
We're adding ability to cross-include DT files between arm and arm64,
by creating appropriate links in the dt-include directory, and using
arm/ and arm64/ as include prefixes. This will avoid other local hacks
such as per-file links between the two arch trees (this broke for
external mirroring of DT contents). Now they can just provide their
own appropriate dt-include hierarcy per platform"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (349 commits)
ARM: dts: exynos: Use - instead of @ for DT OPP entries
arm: spear6xx: add DT description of the ADC on SPEAr600
arm: spear6xx: remove unneeded pinctrl properties in spear600-evb
arm: spear6xx: switch spear600-evb to the new flash partition DT binding
arm: spear6xx: fix spaces in spear600-evb.dts
arm: spear6xx: use node labels in spear600-evb.dts
arm: spear6xx: add labels to various nodes in spear600.dtsi
ARM: dts: vexpress: fix few unit address format warnings
ARM: dts: at91: sama5d3_xplained: not all ADC channels are available
ARM: dts: at91: sama5d3_xplained: fix ADC vref
ARM: dts: at91: add envelope detector mux to the Axentia TSE-850
ARM: dts: armada-38x: label USB and SATA nodes
ARM: dts: imx6q-utilite-pro: add hpd gpio
ARM: dts: imx6qp-sabresd: Set reg_arm regulator supply
ARM: dts: imx6qdl-sabresd: Set LDO regulator supply
ARM: dts: imx: add Gateworks Ventana GW5903 support
ARM: dts: i.MX25: add AIPS control registers
ARM: dts: imx7-colibri: add Carrier Board 3.3V/5V regulators
ARM: dts: imx7-colibri: remove 1.8V fixed regulator
ARM: dts: imx7-colibri: allow to disable Ethernet rail
...
Currently the slope and offset values for calculating the
hot spot temperature of a particular thermal zone is part
of driver data. Pass them here instead and obtain the values
while of node parsing.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
After the ti-cpufreq driver has been added, we can now drop the
operating-points table present in dra7.dtsi for the cpu and add an
operating-points-v2 table with all OPPs available for all silicon
revisions. Also add necessary data for use by ti-cpufreq to selectively
enable the appropriate OPPs at runtime as part of the operating-points
table.
As we now need to define voltage ranges for each OPP, we define the
minimum and maximum voltage to match the ranges possible for AVS class0
voltage as defined by the DRA7/AM57 Data Manual, with the exception of
using a range for OPP_OD based on historical data to ensure that SoCs
from older lots still continue to boot, even though more optimal voltages
are now the standard. Once an AVS Class0 driver is in place it will be
possible for these OPP voltages to be adjusted to any voltage within the
provided range.
Information from SPRS953, Revised December 2015.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
eviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
A total of 380 patches this time, mostly adding support for more hardware
in the device tree descriptions. There is not much exciting here for 4.11,
but I've tried my best to condense the information from the pull requests
I got into a readable summary.
Noteworthy changes to existing platforms include:
- The GIC memory map was a bit wrong almost everywhere and now
gets fixed up
- The Allwinner platforms convert to the generic pinmux properties
- The Marvell EBU platforms now use the new DSA binding
- Samsung Exynos4212 was unused and gets removed
- The Renesas power management got improved
New production machines:
- Lego Mindstorms EV3
https://www.lego.com/en-us/mindstorms/about-ev3
- Beelink X2 Android media box
http://linux-sunxi.org/Beelink_X2
- "Romulus" baseboard management controller for OpenPower
- Axentia TSE-850 Data Radio Channel (DARC) encoder
http://www.axentia.se/db/equipment.html
- Luxul XAP-1410 and XWR-1200 wireless access points
https://luxul.com/xap-1410
New SoCs:
- Allwinner H2+ and V3s, both minor variations of already
supported chips
http://www.allwinnertech.com/index.php?c=product&a=index&id=38
- Marvell Prestera DX packet processors based on Armada XP architecture
http://www.marvell.com/switching/prestera-dx/
- Samsung Exynos4412 Prime gets added, a minor variation of Exynos4412
New developer and reference boards:
- Lichee Pi One, Lichee Pi Zero and Orange Pi Zero,
all based on Allwinner SoCs
http://linux-sunxi.org/LicheePi_Onehttp://www.orangepi.org/orangepizero/
- SAMA5d36ek Reference platform
http://www.atmel.com/tools/sama5d36-ek.aspx
- Beaglebone Green Wireless and Black Wireless
https://beagleboard.org/black-wirelesshttps://beagleboard.org/green-wireless
- phyCORE-AM335x System on Module
http://phytec.com/products/system-on-modules/phycore/am335x/
- New revision of "vf610-zii" Zodiac Inflight Innovations board
- Various i.MX System-on-Module: Is.IoT MX6UL, SavageBoard, Engicam i.Core
http://www.opossom.com/english/index.htmlhttp://www.savageboard.org/http://www.engicam.com/en/products/embedded/som/sodimm/is-iot-mx6ulhttp://www.engicam.com/en/products/embedded/som/sodimm/i-core-m6s-dl-d-q
- Liebherr (LWN) monitor 6 based on i.MX6 Quad, no idea what this is
Cleanups and bugfixes on at91, bcm53xx, i.MX, mvebu, omap, oxnas, qcom,
rockchip, sti, stm32 and tegra
New device supports added to some boards and SoCs, briefly by platform:
- Allwinner: SPDIF, A33 cpufreq, A33 Mali GPU
- Aspeed: network, ipmi bt, gpio, pinmux
- Broadcom: video encoder for raspberry pi, qspi, ethernet, sd/mmc
- TI DaVinci: gpio, lcdc, usb, video-in, uart
- TI Keystone 2: MSM RAM, power/reset, uart
- Mediatek MT2701: clocks, iommu, spi, nand, adc, thermal
- Marvell EBU: ethernet switch on Turris Omnia
- NXP i.MX: otp ram, USB, wifi, bluetooth, spdif, spi, pmic,
eeprom, mmc, nand
- TI OMAP:
- Qualcomm: coresight, gyro/accelerometer, hdmi
- Renesas: pmic, soc-id
- Rockchip: qos
- Samsung: audio on Odroid-X
- Socfpga: FPGA manager, i2c, led, can, watchdog, nand, power monitor
- STi: video in/out
- STM32: timer, pwm, i2c, rtc, add, i2s
- NVIDIA Tegra: tpm
- Uniphier: mmc/sd pinmux
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ucQ/
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Arnd Bergmann:
"A total of 380 patches this time, mostly adding support for more
hardware in the device tree descriptions. There is not much exciting
here for 4.11, but I've tried my best to condense the information from
the pull requests I got into a readable summary.
Noteworthy changes to existing platforms include:
- The GIC memory map was a bit wrong almost everywhere and now gets
fixed up
- The Allwinner platforms convert to the generic pinmux properties
- The Marvell EBU platforms now use the new DSA binding
- Samsung Exynos4212 was unused and gets removed
- The Renesas power management got improved
New production machines:
- Lego Mindstorms EV3:
https://www.lego.com/en-us/mindstorms/about-ev3
- Beelink X2 Android media box:
http://linux-sunxi.org/Beelink_X2
- "Romulus" baseboard management controller for OpenPower
- Axentia TSE-850 Data Radio Channel (DARC) encoder:
http://www.axentia.se/db/equipment.html
- Luxul XAP-1410 and XWR-1200 wireless access points:
https://luxul.com/xap-1410
New SoCs:
- Allwinner H2+ and V3s, both minor variations of already supported
chips:
http://www.allwinnertech.com/index.php?c=product&a=index&id=38
- Marvell Prestera DX packet processors based on Armada XP
architecture:
http://www.marvell.com/switching/prestera-dx/
- Samsung Exynos4412 Prime gets added, a minor variation of
Exynos4412
New developer and reference boards:
- Lichee Pi One, Lichee Pi Zero and Orange Pi Zero, all based on
Allwinner SoCs:
http://linux-sunxi.org/LicheePi_Onehttp://www.orangepi.org/orangepizero/
- SAMA5d36ek Reference platform:
http://www.atmel.com/tools/sama5d36-ek.aspx
- Beaglebone Green Wireless and Black Wireless:
https://beagleboard.org/black-wirelesshttps://beagleboard.org/green-wireless
- phyCORE-AM335x System on Module:
http://phytec.com/products/system-on-modules/phycore/am335x/
- New revision of "vf610-zii" Zodiac Inflight Innovations board
- Various i.MX System-on-Module: Is.IoT MX6UL, SavageBoard, Engicam
i.Core:
http://www.opossom.com/english/index.htmlhttp://www.savageboard.org/http://www.engicam.com/en/products/embedded/som/sodimm/is-iot-mx6ulhttp://www.engicam.com/en/products/embedded/som/sodimm/i-core-m6s-dl-d-q
- Liebherr (LWN) monitor 6 based on i.MX6 Quad, no idea what this is
- Cleanups and bugfixes on at91, bcm53xx, i.MX, mvebu, omap, oxnas,
qcom, rockchip, sti, stm32 and tegra
New device supports added to some boards and SoCs, briefly by platform:
- Allwinner: SPDIF, A33 cpufreq, A33 Mali GPU
- Aspeed: network, ipmi bt, gpio, pinmux
- Broadcom: video encoder for raspberry pi, qspi, ethernet, sd/mmc
- TI DaVinci: gpio, lcdc, usb, video-in, uart
- TI Keystone 2: MSM RAM, power/reset, uart
- Mediatek MT2701: clocks, iommu, spi, nand, adc, thermal
- Marvell EBU: ethernet switch on Turris Omnia
- NXP i.MX: otp ram, USB, wifi, bluetooth, spdif, spi, pmic, eeprom,
mmc, nand
- TI OMAP:
- Qualcomm: coresight, gyro/accelerometer, hdmi
- Renesas: pmic, soc-id
- Rockchip: qos
- Samsung: audio on Odroid-X
- Socfpga: FPGA manager, i2c, led, can, watchdog, nand, power monitor
- STi: video in/out
- STM32: timer, pwm, i2c, rtc, add, i2s
- NVIDIA Tegra: tpm
- Uniphier: mmc/sd pinmux"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (380 commits)
ARM: dts: armada-385-linksys: fix DSA compatible property
ARM: dts: Fix typo in armada-xp-98dx4251
ARM: DTS: Fix register map for virt-capable GIC
dt-bindings: arm,gic: Fix binding example for a virt-capable GIC
ARM: dts: sun8i: sinlinx: Enable audio nodes
ARM: dts: sun8i: parrot: Enable audio nodes
ARM: dts: sun8i: Add audio codec, dai and card for A33
ARM: dts: Add EMAC AXI settings for Arria10
ARM: dts: am335x-chiliboard: Support charger
ARM: dts: am335x-chiliboard: Support power button
ARM: sun8i: dt: Add mali node
dt-bindings: gpu: Add Mali Utgard bindings
ARM: dts: stm32: Add I2C1 support for STM32429 eval board
ARM: dts: stm32: Add I2C1 support for STM32F429 SoC
ARM: dts: stm32: Use clock DT binding definition on stm32f429 family
dt-bindings: mfd: stm32f4: Add missing binding definition
dt-bindings: mfd: stm32f4: Fix STM32F4_X_CLOCK() macro
ARM: dts: stm32: Enable pwm1 and pwm3 for stm32f469-disco
ARM: dts: stm32: add Timers driver for stm32f429 MCU
ARM: dts: add the AB8500 sysclk to the device trees
...
Since everybody copied my own mistake from the DT binding example,
let's address all the offenders in one swift go.
Most of them got the CPU interface size wrong (4kB, while it should
be 8kB), except for both keystone platforms which got the control
interface wrong (4kB instead of 8kB).
In a few cases where I knew for sure what implementation was used,
I've added the "arm,gic-400" compatible string. I'm 99% sure that
this is what everyone is using, but short of having the TRM for
all the other SoCs, I've left them alone.
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Roger Quadros