[ Upstream commit 65277100caa2f2c62b6f3c4648b90d6f0435f3bc ]
In case RSI9116 SDIO WiFi operates in STA mode against Intel 9260 in AP mode,
the association fails. The former is using wpa_supplicant during association,
the later is set up using hostapd:
iwl$ cat hostapd.conf
interface=wlp1s0
ssid=test
country_code=DE
hw_mode=g
channel=1
wpa=2
wpa_passphrase=test
wpa_key_mgmt=WPA-PSK
iwl$ hostapd -d hostapd.conf
rsi$ wpa_supplicant -i wlan0 -c <(wpa_passphrase test test)
The problem is that the TX EAPOL data descriptor RSI_DESC_REQUIRE_CFM_TO_HOST
flag and extended descriptor EAPOL4_CONFIRM frame type are not set in case the
AP is iwlwifi, because in that case the TX EAPOL packet is 2 bytes shorter.
The downstream vendor driver has this change in place already [1], however
there is no explanation for it, neither is there any commit history from which
such explanation could be obtained.
[1] https://github.com/SiliconLabs/RS911X-nLink-OSD/blob/master/rsi/rsi_91x_hal.c#L238
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Angus Ainslie <angus@akkea.ca>
Cc: David S. Miller <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Martin Kepplinger <martink@posteo.de>
Cc: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Cc: Siva Rebbagondla <siva8118@gmail.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201015111616.429220-1-marex@denx.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 92aafe77123ab478e5f5095878856ab0424910da upstream.
The driver would fail to stop the command timer in most error paths,
something which specifically could lead to the timer being freed while
still active on I/O errors during probe.
Fix this by making sure that each function starting the timer also stops
it in all relevant error paths.
Reported-by: syzbot+1d1597a5aa3679c65b9f@syzkaller.appspotmail.com
Fixes: b78e91bcfb ("rsi: Add new firmware loading method")
Cc: stable <stable@vger.kernel.org> # 4.12
Cc: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Cc: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
New firmware files and firmware loading method are added for 9116.
Signed-off-by: Siva Rebbagondla <siva8118@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Till software bootloader ready state, communication with device is common
for 9113 and 9116. Hence moved that part of firmware loading to separate
function rsi_prepare_fw_load(). Also LMAC_VER_OFFSET is different for 9113
and 9116, so renamed existing macro to LMAC_VER_OFFSET_9113
Signed-off-by: Siva Rebbagondla <siva8118@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With the current approach of scanning, roaming delays are observed.
Firmware has support for back ground scanning. To get this advantage,
mac80211 hardware scan is implemented, which decides type of scan to
do based on connected state.
When station is in not connected, driver returns with special value 1
to trigger software scan in mac80211. In case of connected state,
background scan will be triggered.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/rsi/rsi_91x_hal.c: In function 'rsi_send_data_pkt':
drivers/net/wireless/rsi/rsi_91x_hal.c:288:5: warning:
variable 'header_size' set but not used [-Wunused-but-set-variable]
'tx_params' only used for 'header_size' dereferenced,so also
can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Variables bss, wh and temp_flash_content are being assigned but are
never used hence they are redundant and can be removed.
Cleans up clang warnings:
warning: variable 'bss' set but not used [-Wunused-but-set-variable]
warning: variable 'wh' set but not used [-Wunused-but-set-variable]
warning: variable 'temp_flash_content' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently, AP mode will work on only WLAN alone firmware. To give support
for AP and BT dual mode, adding firmware entry in 'struct ta_metadata'.
The firmware entry is based on what coex_mode is used in driver and coex
mode '4' for all AP+BT related functionalities. Hence, added the same.
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
while cleaning up the driver, observed that flash_content pointer is not
necessary in rsi_load_firmware(). Instead of this, driver can use
'fw_entry->data' directly.Hence, removed redundant flash_content pointer.
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
observed low throughput rates during verification. This is because, QoS
enable flag is overridden by sequence number in the data descriptor frame.
Hence, added the fix for same.
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Sushant Kumar Mishra <sushant.mishra@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
To support roaming below changes are done:
* Station notify frame is send to firmware after sending assoc
request. This will avoid dropping of first EAPOL frame due to
delay in creation of station control block in firmware.
* Data queues are unblocked after sending station notify in open
mode, after configuring key in WEP mode, and after receiving
EAPOL4 confirm in WPA mode.
* Initial EAPOL frames priority is chaged to MGMT, rekey EAPOL
frames priority changed to VO.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Descriptors preparation is moved to core instead of HAL to
avoid synchronization issues in sending TX frames
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
All descriptor structures are in rsi_mgmt.h except this
extended descriptor structure. Hence moving it to rsi_mgmt.h
and also renaming to rsi_xtend_desc.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
BT frames are passed through coex and hal modules to BUS.
After firmware is loaded, based on the operating mode CARD
READY frame comes for each protocol. When BT card ready is
received, BT attach is called.
Protocol operations are exchanged between the modules
at initialization time.
Build flag CONFIG_RSI_COEX is introduced to enable coex support
if CONFIG_BT_RSIHCI is enabled. Coex operations are valid if
coex mode is greater than 1 only.
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With BT support, driver has to handle two streams of data
(i.e. wlan and BT). Actual coex implementation is in firmware.
Coex module just schedule the packets to firmware by taking them
from the corresponding paths.
Structures for module and protocol operations are introduced for
this purpose. Protocol operations structure is global structure
which can be shared among different modules. Move initialization
of coex and operating mode values to rsi_91x_init().
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Cc: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Cc: Pavani Muthyala <pavani.muthyala@redpinesignals.com>
Cc: Karun Eagalapati <karun256@gmail.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The first pull request for 4.15, unusually late this time but still
relatively small. Also includes merge from wireless-drivers to fix
conflicts in iwlwifi.
Major changes:
rsi
* add P2P mode support
* sdio suspend and resume support
iwlwifi
* A fix and an addition for PCI devices for the A000 family
* Dump PCI registers when an error occurs, to make it easier to debug
rtlwifi
* add support for 64 bit DMA, enabled with a module parameter
* add module parameter to enable ASPM
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZ5x32AAoJEG4XJFUm622b22EIAKmIlD1tAXxK9YAtYE5AnD5A
QpklYuVJA4XFtpN9UKXP/KCGTRnflW6i4RQ3dt6WKNULkL8RMAjwDijxXrFz8YXw
uB1Aw+Rbmx8eSrWKTgBCLlfU4J3j8jj5gSc7rzYeG7DnMFVShRCxRChiR09GhY4n
gXX3p4+migW128EyQ4KYYFGxipS+5/0igsSwqE6UIyxDuhINjCS9MipwXmv2uG+G
eYOSlwPE+LI8rObqlaJKVgam77srQqZLnPnima+bKAYXiQOPxPDBLwGP1qjo38Wa
pHKDG//OPMOjyUccl5axulnvLPTjyng9jYNpzJlLLz9+M29SudtHI7YQQHhBj5M=
=bApF
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2017-10-18' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.15
The first pull request for 4.15, unusually late this time but still
relatively small. Also includes merge from wireless-drivers to fix
conflicts in iwlwifi.
Major changes:
rsi
* add P2P mode support
* sdio suspend and resume support
iwlwifi
* A fix and an addition for PCI devices for the A000 family
* Dump PCI registers when an error occurs, to make it easier to debug
rtlwifi
* add support for 64 bit DMA, enabled with a module parameter
* add module parameter to enable ASPM
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We will dump information about firmware version, firmware file
name and operating mode during initialization.
Signed-off-by: Pavani Muthyala <pavani.muthyala@redpinesignals.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Data descriptor is updated to include vap_id. TX command frame
key config also updated to include vap_id.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Parameter 'vif' is passed to inform_bss_status function to
check the type of vif and to get vap_id.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Station id needs to be get for data and management frames
to fill in the descruptor for AP mode. Few other changes
related to AP mode are covered here.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Mac80211 config parameter BEACON_ENABLE is handled. When VAP
capabilities frame with AP mode is configured to firmware, beacon
events start coming to host at each PreTBTT. At this time, beacon
is taken from mac80211, descriptor is prepared and send to firmware.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds support for legacy power save. Necessary
configuration frames are downloaded to firmware when power save
is enabled/disabled
Signed-off-by: Karun Eagalapati <karun256@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Data packet descriptor preparation code is moved a separate
function.
Signed-off-by: Pavani Muthyala <pavani.muthyala@redpinesignals.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch covers some enhancements in data packet descriptor
preparation especially for EAPOL, multicast/broadcast packets.
Signed-off-by: Pavani Muthyala <pavani.muthyala@redpinesignals.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently this descriptor is prepared with the help of __le16
pointer. This patch makes use of a structure to prepare the
descriptor in a cleaner way.
Signed-off-by: Pavani Muthyala <pavani.muthyala@redpinesignals.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Management descriptor preparation is move to a separate function
as it will be called from a different context in upcoming patches.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently this descriptor is prepared with the help of __le16
pointer. This patch makes use of a structure to prepare the
descriptor in a cleaner way.
Signed-off-by: Pavani Muthyala <pavani.muthyala@redpinesignals.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
immediate wakeup bit is set while sending internal management
frame to the firmware.
Signed-off-by: Karun Eagalapati <karun256@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
After successful loading of firmware, a CARD READY indication is
received by host. Common device configuration parameters are sent
to the device after this. It includes information like device
operating mode (Wi-Fi alone or BT coex), power save related
parameters, GPIO information etc. As device supports BT coex,
this frame is send in COEX queue initially. Based on the operating
mode, CARD READY indication is received from each protocol module
in firmware i.e. WLAN, BT.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Before firmware load, sometimes false interrupts are received.
System hang is observed if interrupt handler is not registered
to receive these interrupts. Hence interrupt handler registration
is moved before firmware load. We will drop these false interrupts
as these are not from the device.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
linux-firmware maintainers prefer to have a subdirectory for
firmware files. Code is changed here to pick firmware file from
a subdirectory. Firmware file with a new loading mechanism will
be submitted inside rsi directory.
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The older firmware loading method has been deprecated and not in use
for any chipets. New method is introduced which works based on soft
boot loader. In this method, complete RAM image and FLASH image are
present in the flash. Before loading the functional firmware, host
issues boot loader commands to verify whether firmware to load is
different from the current functional firmware. If not, firmware
upgrade progresses and boot loader will switch to the new functional
firmware.
"rs9113_wlan_qspi.rps" is the firmware filename used in this patch.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Host interface operations are currently function pointers in rsi_hw
structure. As more host interface operations are going to be introduced,
separate structure is added for these for convenience.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The file rsi_91x_hal.c is going to contain device specific code i.e new
firmware loading method for RS9113 chipset. As the file rsi_91x_pkt.c
contains code to prepare device specific descriptors for transmit packet,
this file is renamed to rsi_91x_hal.c which is more relevant as per it's
functionality.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
