[ Upstream commit 46f94c7818e7ab82758fca74935ef3d454340b4e ]
If the mv88e6xxx DSA driver is built as a module, it causes the
ethernet driver to re-probe when it's loaded. This in turn causes
the gigabit PHY to be momentarily reset and reprogrammed. However,
we attempt to reprogram the PHY immediately after deasserting reset,
and the PHY ignores the writes.
This results in the PHY operating in the wrong mode, and the copper
link states down.
Set a reset deassert delay of 10ms for the gigabit PHY to avoid this.
Fixes: babc5544c2 ("arm64: dts: clearfog-gt-8k: 1G eth PHY reset signal")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 62bba54d99407aedfe9b0a02e72e23c06e2b0116 upstream.
Explicitly set the switch cpu (upstream) port phy-mode and managed
properties. This fixes the Marvell 88E6141 switch serdes configuration
with the recently enabled phylink layer.
Fixes: a612083327 ("arm64: dts: add support for SolidRun Clearfog GT 8K")
Reported-by: Denis Odintsov <d.odintsov@traviangames.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Update Aramda 7k/8k DTs to use the phy-supply property of the (recent)
generic PHY framework instead of the (legacy) usb-phy preperty. Both
enable the supply when the PHY is enabled.
The COMPHY nodes only provide SERDES lanes configuration. The power
supply that is represented by the phy-supply property is just a
regulator wired to the USB connector, hence the creation of connector
nodes as child of the COMPHY nodes and the supply attached to it.
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Fill-in the missing PCIe phys/phy-names DT properties of Armada 7k/8k
based boards.
The MacchiatoBin is a bit particular as the Armada8k-PCI IP supports
x4 link widths and in this case the PHY for each lane must be
referenced.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Fill-in the missing USB3 phys/phy-names DT properties of Armada 7k/8k
based boards. Only update nodes actually enabling USB3 in the default
(mainline) configuration. A few USB nodes are enabled but there is
only USB2 working on them.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Fill-in the missing SATA phys/phy-names DT properties of Armada 7k/8k
based boards.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
The Clearfog GT-8K board is capable of supplying power up to 2W to SFP
modules. Make that explicit in the device-tree. Without this property
current kernel does not allow SFP modules that require more than 1W.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
There is currently no DT binding for GPIO rfkill signals. To make
mini-PCIe attached WiFi devices work, use gpio-hog to hold the
wlan_disable signal de-asserted.
Signed-off-by: Thomas Schreiber <tschreibe@gmail.com>
[baruch: add pinctrl node; rename tag]
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Enable the USB3 peripheral that is wired to CON2 on the Clearfog GT-8K
board.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Deassert the reset and wireless disable signals on the CON2 mini-PCIe
socket. That allows the host to detect USB devices on the mini-PCIe
socket.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
This reset signal controls the Marvell 1512 1G PHY.
Note that current implementation queries the PHY over the MDIO bus
(get_phy_device() call from of_mdiobus_register_phy()) before reset
signal deassert. If the PHY reset signal is asserted at boot time, PHY
registration fails. So current code relies on the bootloader to deassert
the reset signal.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
The fixed regulator driver ignores the gpio flags, so this change has
no practical effect in the current implementation. Fix it anyway to
correct the hardware description.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
This adds support for the PCIe interface on the CON4 mini-PCIe
connector.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
The SolidRun Clearfog GT-8K is based on Marvell Armada 8040 SoC.
https://wiki.solid-run.com/doku.php?id=products:a8040:clearfoggt8k
The following devices were tested with this DT on top of kernel
v4.19-rc4:
* 1GB Ethernet WAN
* 4 ports 1GB Ethernet switch (2.5GB uplink)
* SFP port
* SATA on CON3 PCIe slot
* USB3 type A port
* SD card and eMMC
* 2 LEDs
* 2 push buttons
[gregory: fix block comment alignement]
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
