When IOMMU is enabled, iova -> phys address translation should be
performed using iommu_ops, not dma_to_phys().
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Use the controller device for caam/qi instead of allocating
a new platform device.
This is needed as a preparation to add support for working behind an
SMMU. A platform device allocated using platform_device_register_full()
is not completely set up - most importantly .dma_configure()
is not called.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Currently we allow top level code, i.e. that which sits between the
low level (HW-specific) drivers and crypto API, to be built as several
drivers: caamalg, caamhash, caam_pkc, caamrng, caamalg_qi.
There is no advantage in this, more it interferes with adding support
for deferred probing (there are no corresponding devices and thus
no bus).
Convert these drivers and call init() / exit() manually at the right
time.
Move algorithms initialization at JR probe / remove time:
-the first probed JR registers the crypto algs
-the last removed JR unregisters the crypto algs
Note: caam_qi_init() is called before JR platform devices creation
(of_populate_bus()), such that QI interface is initialized when
the caam/qi algorithms are registered in the JR driver (by calling
caam_qi_algapi_init().
While here, fix the Kconfig entries under CRYPTO_DEV_FSL_CAAM_JR
to be aligned.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
For each job ring, the variable 'ringsize' is initialised but never
used. Similarly variables 'inp_ring_write_index' and 'head' always track
the same value and instead of 'inp_ring_write_index', caam_jr_enqueue()
can use 'head' itself. Both these variables have been removed.
Signed-off-by: Vakul Garg <vakul.garg@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
For each job ring pair, the output ring is processed exactly by one cpu
at a time under a tasklet context (one per ring). Therefore, there is no
need to protect a job ring's access & its private data structure using a
lock. Hence the lock can be removed.
Signed-off-by: Vakul Garg <vakul.garg@nxp.com>
Reviewed-by: Horia Geanta <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Instead of reading job ring's occupancy registers for every req/rsp
enqueued/dequeued respectively, we read these registers once and store
them in memory. After completing a job enqueue/dequeue, we decrement
these values. When these values become zero, we refresh the snapshot of
job ring's occupancy registers. This eliminates need of expensive device
register read operations for every job enqueued and dequeued and hence
makes caam_jr_enqueue() and caam_jr_dequeue() faster. The performance of
kernel ipsec improved by about 6% on ls1028 (for frame size 408 bytes).
Signed-off-by: Vakul Garg <vakul.garg@nxp.com>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: "Horia Geantă" <horia.geanta@nxp.com>
Cc: Aymen Sghaier <aymen.sghaier@nxp.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-crypto@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Management Complex (MC) f/w detection is based on CTPR_MS[DPAA2] bit.
This is incorrect since:
-the bit is set for all CAAM blocks integrated in SoCs with a certain
Layerscape Chassis
-some SoCs with LS Chassis don't have an MC block (thus no MC f/w)
To fix this, MC f/w detection will be based on the presence of
"fsl,qoriq-mc" compatible string in the device tree.
Fixes: 297b9cebd2 ("crypto: caam/jr - add support for DPAA2 parts")
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Save Era in driver's private data for further usage,
like deciding whether an erratum applies or a feature is available
based on its value.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Most of the dentry members from structure caam_drv_private
are never used at all, so it is safe to remove them.
Since debugfs_remove_recursive() is called, we don't need the
file entries.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The way Job Ring platform devices are created and released does not
allow for multiple create-release cycles.
JR0 Platform device creation error
JR0 Platform device creation error
caam 2100000.caam: no queues configured, terminating
caam: probe of 2100000.caam failed with error -12
The reason is that platform devices are created for each job ring:
for_each_available_child_of_node(nprop, np)
if (of_device_is_compatible(np, "fsl,sec-v4.0-job-ring") ||
of_device_is_compatible(np, "fsl,sec4.0-job-ring")) {
ctrlpriv->jrpdev[ring] =
of_platform_device_create(np, NULL, dev);
which sets OF_POPULATED on the device node, but then it cleans these up:
/* Remove platform devices for JobRs */
for (ring = 0; ring < ctrlpriv->total_jobrs; ring++) {
if (ctrlpriv->jrpdev[ring])
of_device_unregister(ctrlpriv->jrpdev[ring]);
}
which leaves OF_POPULATED set.
Use of_platform_populate / of_platform_depopulate instead.
This allows for a bit of driver clean-up, jrpdev is no longer needed.
Logic changes a bit too:
-exit in case of_platform_populate fails, since currently even QI backend
depends on JR; true, we no longer support the case when "some" of the JR
DT nodes are incorrect
-when cleaning up, caam_remove() would also depopulate RTIC in case
it would have been populated somewhere else - not the case for now
Cc: <stable@vger.kernel.org>
Fixes: 313ea293e9 ("crypto: caam - Add Platform driver for Job Ring")
Reported-by: Russell King <rmk+kernel@armlinux.org.uk>
Suggested-by: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
CAAM engine supports two interfaces for crypto job submission:
-job ring interface - already existing caam/jr driver
-Queue Interface (QI) - caam/qi driver added in current patch
QI is present in CAAM engines found on DPAA platforms.
QI gets its I/O (frame descriptors) from QMan (Queue Manager) queues.
This patch adds a platform device for accessing CAAM's queue interface.
The requests are submitted to CAAM using one frame queue per
cryptographic context. Each crypto context has one shared descriptor.
This shared descriptor is attached to frame queue associated with
corresponding driver context using context_a.
The driver hides the mechanics of FQ creation, initialisation from its
applications. Each cryptographic context needs to be associated with
driver context which houses the FQ to be used to transport the job to
CAAM. The driver provides API for:
(a) Context creation
(b) Job submission
(c) Context deletion
(d) Congestion indication - whether path to/from CAAM is congested
The driver supports affining its context to a particular CPU.
This means that any responses from CAAM for the context in question
would arrive at the given CPU. This helps in implementing one CPU
per packet round trip in IPsec application.
The driver processes CAAM responses under NAPI contexts.
NAPI contexts are instantiated only on cores with affined portals since
only cores having their own portal can receive responses from DQRR.
The responses from CAAM for all cryptographic contexts ride on a fixed
set of FQs. We use one response FQ per portal owning core. The response
FQ is configured in each core's and thus portal's dedicated channel.
This gives the flexibility to direct CAAM's responses for a crypto
context on a given core.
Signed-off-by: Vakul Garg <vakul.garg@nxp.com>
Signed-off-by: Alex Porosanu <alexandru.porosanu@nxp.com>
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This reverts commit 66d2e20280.
Quoting from Russell's findings:
https://www.mail-archive.com/linux-crypto@vger.kernel.org/msg21136.html
[quote]
Okay, I've re-tested, using a different way of measuring, because using
openssl speed is impractical for off-loaded engines. I've decided to
use this way to measure the performance:
dd if=/dev/zero bs=1048576 count=128 | /usr/bin/time openssl dgst -md5
For the threaded IRQs case gives:
0.05user 2.74system 0:05.30elapsed 52%CPU (0avgtext+0avgdata 2400maxresident)k
0.06user 2.52system 0:05.18elapsed 49%CPU (0avgtext+0avgdata 2404maxresident)k
0.12user 2.60system 0:05.61elapsed 48%CPU (0avgtext+0avgdata 2460maxresident)k
=> 5.36s => 25.0MB/s
and the tasklet case:
0.08user 2.53system 0:04.83elapsed 54%CPU (0avgtext+0avgdata 2468maxresident)k
0.09user 2.47system 0:05.16elapsed 49%CPU (0avgtext+0avgdata 2368maxresident)k
0.10user 2.51system 0:04.87elapsed 53%CPU (0avgtext+0avgdata 2460maxresident)k
=> 4.95 => 27.1MB/s
which corresponds to an 8% slowdown for the threaded IRQ case. So,
tasklets are indeed faster than threaded IRQs.
[...]
I think I've proven from the above that this patch needs to be reverted
due to the performance regression, and that there _is_ most definitely
a deterimental effect of switching from tasklets to threaded IRQs.
[/quote]
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Threaded interrupts can perform the function of the tasklet, and much
more safely too - without races when trying to take the tasklet and
interrupt down on device removal.
With the old code, there is a window where we call tasklet_kill(). If
the interrupt handler happens to be running on a different CPU, and
subsequently calls tasklet_schedule(), the tasklet will be re-scheduled
for execution.
Switching to a hardirq/threadirq combination implementation avoids this,
and it also means generic code deals with the teardown sequencing of the
threaded and non-threaded parts.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
ARM-based systems may disable clocking to the CAAM device on the
Freescale i.MX platform for power management purposes. This patch
enables the required clocks when the CAAM module is initialized and
disables the required clocks when the CAAM module is shut down.
Signed-off-by: Victoria Milhoan <vicki.milhoan@freescale.com>
Tested-by: Horia Geantă <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
CAAM's memory is broken into following address blocks:
Block Included Registers
0 General Registers
1-4 Job ring registers
6 RTIC registers
7 QI registers
8 DECO and CCB
Size of the above stated blocks varies in various platforms. The block size can be 4K or 64K.
The block size can be dynamically determined by reading CTPR register in CAAM.
This patch initializes the block addresses dynamically based on the value read from this register.
Signed-off-by: Ruchika Gupta <r66431@freescale.com>
Signed-off-by: Nitesh Narayan Lal <b44382@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
For platforms with virtualization enabled
1. The job ring registers can be written to only is the job ring has been
started i.e STARTR bit in JRSTART register is 1
2. For DECO's under direct software control, with virtualization enabled
PL, BMT, ICID and SDID values need to be provided. These are provided by
selecting a Job ring in start mode whose parameters would be used for the
DECO access programming.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
- Earlier interface layers - caamalg, caamhash, caamrng were
directly using the Controller driver private structure to access
the Job ring.
- Changed the above to use alloc/free API's provided by Job Ring Drive
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Reviewed-by: Garg Vakul-B16394 <vakul@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
With each of the Job Ring available as a platform device, the
Job Ring driver needs to take care of allocation/deallocation
of the Job Rings to the above interface layers. Added APIs
in Job Ring Driver to allocate/free Job rings
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Reviewed-by: Garg Vakul-B16394 <vakul@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The SEC Job Rings are now available as individual devices.
This would enable sharing of job rings between kernel and
user space. Job Rings can now be dynamically bound/unbound
from kernel.
Changes are made in the following layers of CAAM Driver
1. Controller driver
- Does basic initialization of CAAM Block.
- Creates platform devices for Job Rings.
(Earlier the initialization of Job ring was done
by the controller driver)
2. JobRing Platform driver
- Manages the platform Job Ring devices created
by the controller driver
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Reviewed-by: Garg Vakul-B16394 <vakul@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
RNG4 block contains multiple (i.e. 2) state handles that can be
initialized. This patch adds the necessary code for detecting
which of the two state handles has been instantiated by another
piece of software e.g. u-boot and instantiate the other one (or
both if none was instantiated). Only the state handle(s)
instantiated by this driver will be deinstantiated when removing
the module.
Signed-off-by: Alex Porosanu <alexandru.porosanu@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
If the caam driver module instantiates the RNG state handle 0, then
upon the removal of the module, the RNG state handle is left
initialized. This patch takes care of reverting the state of the
handle back to its previous uninstantatied state.
Signed-off-by: Alex Porosanu <alexandru.porosanu@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
there is no noticeable benefit for multiple cores to process one
job ring's output ring: in fact, we can benefit from cache effects
of having the back-half stay on the core that receives a particular
ring's interrupts, and further relax general contention and the
locking involved with reading outring_used, since tasklets run
atomically.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
caam supports ahash hmac with sha algorithms and md5.
Signed-off-by: Yuan Kang <Yuan.Kang@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
remove caam_jr_register and caam_jr_deregister
to allow sharing of job rings.
Signed-off-by: Yuan Kang <Yuan.Kang@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The SEC4 supercedes the SEC2.x/3.x as Freescale's
Integrated Security Engine. Its programming model is
incompatible with all prior versions of the SEC (talitos).
The SEC4 is also known as the Cryptographic Accelerator
and Assurance Module (CAAM); this driver is named caam.
This initial submission does not include support for Data Path
mode operation - AEAD descriptors are submitted via the job
ring interface, while the Queue Interface (QI) is enabled
for use by others. Only AEAD algorithms are implemented
at this time, for use with IPsec.
Many thanks to the Freescale STC team for their contributions
to this driver.
Signed-off-by: Steve Cornelius <sec@pobox.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
