Pins used for joystick are all configured as input. "push-pull" is not a
valid setting for an input pin.
Fixes: a502b343eb ("pinctrl: stmfx: update pinconf settings")
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
"push-pull" configuration is now fully handled by the gpiolib and the
STMFX pinctrl driver. There is no longer need to declare a pinctrl group
to only configure "push-pull" setting for the line. It is done directly by
the gpiolib.
Fixes: a502b343eb ("pinctrl: stmfx: update pinconf settings")
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
The dsi physical layer is powered by the 1v8 power controller supply.
Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
On disco and eval board, Tx and Rx delay are applied (pull-up of 4.7k
put on VDD) so which correspond to RGMII-ID mode with internal RX and TX
delays provided by the PHY, the MAC should not add the RX or TX delays
in this case
Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch adds a new property (power-supply) to panel rm68200 (raydium)
on stm32mp157c-ev1.
Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Enable OV5640 camera sensor driver of MB1379A extension
board connected on CN7 connector of stm32mp157c-ev1 board:
bus-width is set to 8, data-shift is set to 2 (lines 9:2 are used),
hsync-active is set to 0 for horizontal synchro line active low,
vsync-active is set to 0 for vertical synchro line active low and
pclk-sample is set to 1 for pixel clock polarity sampling data
on rising edge of the pixel clock signal.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch adds jedec compatible for spi-nor flash
on stm32mp157c-ev1 (needed with new spi-mem interface).
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
The joystick (B1) on stm32mp157c-ev1 uses gpios on STMFX gpio expander.
These gpios need a pin configuration (push-pull and bias-pull-down),
described under stmfx_pinctrl node.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch adds support for STMicroelectronics Multi-Function eXpander
(STMFX) on stm32mp157c-ev1. It is connected on i2c2.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Spare dmas when using timers on stm32mp157c-ev1.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
MAC is connected to a PHY in RGMII mode.
Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch adds SPI1 support on stm32mp157c-ev1 board.
SPI1 is available on GPIO expansion connector but kept disabled
so these pins can be used as GPIOs by default.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch enables USB OTG HS on stm32mp157c-ev1 in Peripheral mode.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch enables USB Host (USBH) EHCI controller on stm32mp157c-ev1.
As a hub is used between USBH and USB connectors, no need to enable
USBH OHCI controller: all low- and full-speed traffic is managed by the
hub.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add activation of the Controller Area Network m_can on stm32mp157c-ev1
board.
Signed-off-by: Bich Hemon <bich.hemon@st.com>
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch adds flash nor on qspi. Each flash is
connected in quad mode and has its own chip select.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch enables USBPHYC (USB PHY Controller) on stm32mp157c-ev1.
This enables the two usbphyc usb2 ports.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
stm32mp157c evaluation board has TIM2_CH4, TIM8_CH4 and TIM12_CH1
available on GPIO expansion connector.
Add PWM and associated triggers (for ADC/DAC) on these timers.
Keep them disabled so these pins can be used as GPIOs by default.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add support of stm32mp157c evaluation board (part number: STM32MP157C-EV1)
split in 2 elements:
-Daughter board (part number: STM32MP157C-ED1)
which includes CPU, memory and power supply
-Mother board (part number: STM32MP157C-EM1)
which includes external peripherals (like display, camera,...)
and extension connectors.
The daughter board can run alone, this is why the device tree files
are split in two layers, for the complete evaluation board (ev1)
and for the daughter board alone (ed1).
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Amelie Delaunay