[ Upstream commit 364745fbe981a4370f50274475da4675661104df ]
This is technically a backwards incompatible change in behaviour, but I'm
going to argue that it is very unlikely to break things, and likely to fix
*far* more then it breaks.
In no particular order, various reasons follow:
(a) I've long had a bug assigned to myself to debug a super rare kernel crash
on Android Pixel phones which can (per stacktrace) be traced back to BPF clat
IPv6 to IPv4 protocol conversion causing some sort of ugly failure much later
on during transmit deep in the GSO engine, AFAICT precisely because of this
change to gso_size, though I've never been able to manually reproduce it. I
believe it may be related to the particular network offload support of attached
USB ethernet dongle being used for tethering off of an IPv6-only cellular
connection. The reason might be we end up with more segments than max permitted,
or with a GSO packet with only one segment... (either way we break some
assumption and hit a BUG_ON)
(b) There is no check that the gso_size is > 20 when reducing it by 20, so we
might end up with a negative (or underflowing) gso_size or a gso_size of 0.
This can't possibly be good. Indeed this is probably somehow exploitable (or
at least can result in a kernel crash) by delivering crafted packets and perhaps
triggering an infinite loop or a divide by zero... As a reminder: gso_size (MSS)
is related to MTU, but not directly derived from it: gso_size/MSS may be
significantly smaller then one would get by deriving from local MTU. And on
some NICs (which do loose MTU checking on receive, it may even potentially be
larger, for example my work pc with 1500 MTU can receive 1520 byte frames [and
sometimes does due to bugs in a vendor plat46 implementation]). Indeed even just
going from 21 to 1 is potentially problematic because it increases the number
of segments by a factor of 21 (think DoS, or some other crash due to too many
segments).
(c) It's always safe to not increase the gso_size, because it doesn't result in
the max packet size increasing. So the skb_increase_gso_size() call was always
unnecessary for correctness (and outright undesirable, see later). As such the
only part which is potentially dangerous (ie. could cause backwards compatibility
issues) is the removal of the skb_decrease_gso_size() call.
(d) If the packets are ultimately destined to the local device, then there is
absolutely no benefit to playing around with gso_size. It only matters if the
packets will egress the device. ie. we're either forwarding, or transmitting
from the device.
(e) This logic only triggers for packets which are GSO. It does not trigger for
skbs which are not GSO. It will not convert a non-GSO MTU sized packet into a
GSO packet (and you don't even know what the MTU is, so you can't even fix it).
As such your transmit path must *already* be able to handle an MTU 20 bytes
larger then your receive path (for IPv4 to IPv6 translation) - and indeed 28
bytes larger due to IPv4 fragments. Thus removing the skb_decrease_gso_size()
call doesn't actually increase the size of the packets your transmit side must
be able to handle. ie. to handle non-GSO max-MTU packets, the IPv4/IPv6 device/
route MTUs must already be set correctly. Since for example with an IPv4 egress
MTU of 1500, IPv4 to IPv6 translation will already build 1520 byte IPv6 frames,
so you need a 1520 byte device MTU. This means if your IPv6 device's egress
MTU is 1280, your IPv4 route must be 1260 (and actually 1252, because of the
need to handle fragments). This is to handle normal non-GSO packets. Thus the
reduction is simply not needed for GSO packets, because when they're correctly
built, they will already be the right size.
(f) TSO/GSO should be able to exactly undo GRO: the number of packets (TCP
segments) should not be modified, so that TCP's MSS counting works correctly
(this matters for congestion control). If protocol conversion changes the
gso_size, then the number of TCP segments may increase or decrease. Packet loss
after protocol conversion can result in partial loss of MSS segments that the
sender sent. How's the sending TCP stack going to react to receiving ACKs/SACKs
in the middle of the segments it sent?
(g) skb_{decrease,increase}_gso_size() are already no-ops for GSO_BY_FRAGS
case (besides triggering WARN_ON_ONCE). This means you already cannot guarantee
that gso_size (and thus resulting packet MTU) is changed. ie. you must assume
it won't be changed.
(h) changing gso_size is outright buggy for UDP GSO packets, where framing
matters (I believe that's also the case for SCTP, but it's already excluded
by [g]). So the only remaining case is TCP, which also doesn't want it
(see [f]).
(i) see also the reasoning on the previous attempt at fixing this
(commit fa7b83bf3b156c767f3e4a25bbf3817b08f3ff8e) which shows that the current
behaviour causes TCP packet loss:
In the forwarding path GRO -> BPF 6 to 4 -> GSO for TCP traffic, the
coalesced packet payload can be > MSS, but < MSS + 20.
bpf_skb_proto_6_to_4() will upgrade the MSS and it can be > the payload
length. After then tcp_gso_segment checks for the payload length if it
is <= MSS. The condition is causing the packet to be dropped.
tcp_gso_segment():
[...]
mss = skb_shinfo(skb)->gso_size;
if (unlikely(skb->len <= mss)) goto out;
[...]
Thus changing the gso_size is simply a very bad idea. Increasing is unnecessary
and buggy, and decreasing can go negative.
Fixes: 6578171a7f ("bpf: add bpf_skb_change_proto helper")
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Dongseok Yi <dseok.yi@samsung.com>
Cc: Willem de Bruijn <willemb@google.com>
Link: https://lore.kernel.org/bpf/CANP3RGfjLikQ6dg=YpBU0OeHvyv7JOki7CyOUS9modaXAi-9vQ@mail.gmail.com
Link: https://lore.kernel.org/bpf/20210617000953.2787453-2-zenczykowski@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 84316ca4e100d8cbfccd9f774e23817cb2059868 ]
The skb_change_head() helper did not set "skb->mac_len", which is
problematic when it's used in combination with skb_redirect_peer().
Without it, redirecting a packet from a L3 device such as wireguard to
the veth peer device will cause skb->data to point to the middle of the
IP header on entry to tcp_v4_rcv() since the L2 header is not pulled
correctly due to mac_len=0.
Fixes: 3a0af8fd61 ("bpf: BPF for lightweight tunnel infrastructure")
Signed-off-by: Jussi Maki <joamaki@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20210519154743.2554771-2-joamaki@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 6306c1189e77a513bf02720450bb43bd4ba5d8ae upstream.
Multiple BPF-helpers that can manipulate/increase the size of the SKB uses
__bpf_skb_max_len() as the max-length. This function limit size against
the current net_device MTU (skb->dev->mtu).
When a BPF-prog grow the packet size, then it should not be limited to the
MTU. The MTU is a transmit limitation, and software receiving this packet
should be allowed to increase the size. Further more, current MTU check in
__bpf_skb_max_len uses the MTU from ingress/current net_device, which in
case of redirects uses the wrong net_device.
This patch keeps a sanity max limit of SKB_MAX_ALLOC (16KiB). The real limit
is elsewhere in the system. Jesper's testing[1] showed it was not possible
to exceed 8KiB when expanding the SKB size via BPF-helper. The limiting
factor is the define KMALLOC_MAX_CACHE_SIZE which is 8192 for
SLUB-allocator (CONFIG_SLUB) in-case PAGE_SIZE is 4096. This define is
in-effect due to this being called from softirq context see code
__gfp_pfmemalloc_flags() and __do_kmalloc_node(). Jakub's testing showed
that frames above 16KiB can cause NICs to reset (but not crash). Keep this
sanity limit at this level as memory layer can differ based on kernel
config.
[1] https://github.com/xdp-project/bpf-examples/tree/master/MTU-tests
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/161287788936.790810.2937823995775097177.stgit@firesoul
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2c0a10af688c02adcf127aad29e923e0056c6b69 ]
BPF end-user on Cilium slack-channel (Carlo Carraro) wants to use
bpf_fib_lookup for doing MTU-check, but *prior* to extending packet size,
by adjusting fib_params 'tot_len' with the packet length plus the expected
encap size. (Just like the bpf_check_mtu helper supports). He discovered
that for SKB ctx the param->tot_len was not used, instead skb->len was used
(via MTU check in is_skb_forwardable() that checks against netdev MTU).
Fix this by using fib_params 'tot_len' for MTU check. If not provided (e.g.
zero) then keep existing TC behaviour intact. Notice that 'tot_len' for MTU
check is done like XDP code-path, which checks against FIB-dst MTU.
V16:
- Revert V13 optimization, 2nd lookup is against egress/resulting netdev
V13:
- Only do ifindex lookup one time, calling dev_get_by_index_rcu().
V10:
- Use same method as XDP for 'tot_len' MTU check
Fixes: 4c79579b44 ("bpf: Change bpf_fib_lookup to return lookup status")
Reported-by: Carlo Carraro <colrack@gmail.com>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/161287789444.790810.15247494756551413508.stgit@firesoul
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ no upstream commit ]
Fix a potential kernel address leakage for the prerequisite where there is
a BPF program attached to the cgroup/setsockopt hook. The latter can only
be attached under root, however, if the attached program returns 1 to then
run the related kernel handler, an unprivileged program could probe for
kernel addresses that way. The reason this is possible is that we're under
set_fs(KERNEL_DS) when running the kernel setsockopt handler. Aside from
old cBPF there is also SCTP's struct sctp_getaddrs_old which contains
pointers in the uapi struct that further need copy_from_user() inside the
handler. In the normal case this would just return -EFAULT, but under a
temporary KERNEL_DS setting the memory would be copied and we'd end up at
a different error code, that is, -EINVAL, for both cases given subsequent
validations fail, which then allows the app to distinguish and make use of
this fact for probing the address space. In case of later kernel versions
this issue won't work anymore thanks to Christoph Hellwig's work that got
rid of the various temporary set_fs() address space overrides altogether.
One potential option for 5.4 as the only affected stable kernel with the
least complexity would be to remap those affected -EFAULT copy_from_user()
error codes with -EINVAL such that they cannot be probed anymore. Risk of
breakage should be rather low for this particular error case.
Fixes: 0d01da6afc ("bpf: implement getsockopt and setsockopt hooks")
Reported-by: Ryota Shiga (Flatt Security)
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Stanislav Fomichev <sdf@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 700465fd338fe5df08a1b2e27fa16981f562547f ]
In setsockopt(SO_MAX_PACING_RATE) on 64bit systems, sk_max_pacing_rate,
after extended from 'u32' to 'unsigned long', takes unintentionally
hiked value whenever assigned from an 'int' value with MSB=1, due to
binary sign extension in promoting s32 to u64, e.g. 0x80000000 becomes
0xFFFFFFFF80000000.
Thus inflated sk_max_pacing_rate causes subsequent getsockopt to return
~0U unexpectedly. It may also result in increased pacing rate.
Fix by explicitly casting the 'int' value to 'unsigned int' before
assigning it to sk_max_pacing_rate, for zero extension to happen.
Fixes: 76a9ebe811 ("net: extend sk_pacing_rate to unsigned long")
Signed-off-by: Ji Li <jli@akamai.com>
Signed-off-by: Ke Li <keli@akamai.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20201022064146.79873-1-keli@akamai.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e6a18d36118bea3bf497c9df4d9988b6df120689 ]
Bryce reported that he saw the following with:
0: r6 = r1
1: r1 = 12
2: r0 = *(u16 *)skb[r1]
The xlated sequence was incorrectly clobbering r2 with pointer
value of r6 ...
0: (bf) r6 = r1
1: (b7) r1 = 12
2: (bf) r1 = r6
3: (bf) r2 = r1
4: (85) call bpf_skb_load_helper_16_no_cache#7692160
... and hence call to the load helper never succeeded given the
offset was too high. Fix it by reordering the load of r6 to r1.
Other than that the insn has similar calling convention than BPF
helpers, that is, r0 - r5 are scratch regs, so nothing else
affected after the insn.
Fixes: e0cea7ce98 ("bpf: implement ld_abs/ld_ind in native bpf")
Reported-by: Bryce Kahle <bryce.kahle@datadoghq.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/cace836e4d07bb63b1a53e49c5dfb238a040c298.1599512096.git.daniel@iogearbox.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1869e226a7b3ef75b4f70ede2f1b7229f7157fa4 ]
flowi4_multipath_hash was added by the commit referenced below for
tunnels. Unfortunately, the patch did not initialize the new field
for several fast path lookups that do not initialize the entire flow
struct to 0. Fix those locations. Currently, flowi4_multipath_hash
is random garbage and affects the hash value computed by
fib_multipath_hash for multipath selection.
Fixes: 24ba14406c ("route: Add multipath_hash in flowi_common to make user-define hash")
Signed-off-by: David Ahern <dsahern@gmail.com>
Cc: wenxu <wenxu@ucloud.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 84f44df664e9f0e261157e16ee1acd77cc1bb78d ]
Similar to patch ("bpf: sock_ops ctx access may stomp registers") if the
src_reg = dst_reg when reading the sk field of a sock_ops struct we
generate xlated code,
53: (61) r9 = *(u32 *)(r9 +28)
54: (15) if r9 == 0x0 goto pc+3
56: (79) r9 = *(u64 *)(r9 +0)
This stomps on the r9 reg to do the sk_fullsock check and then when
reading the skops->sk field instead of the sk pointer we get the
sk_fullsock. To fix use similar pattern noted in the previous fix
and use the temp field to save/restore a register used to do
sk_fullsock check.
After the fix the generated xlated code reads,
52: (7b) *(u64 *)(r9 +32) = r8
53: (61) r8 = *(u32 *)(r9 +28)
54: (15) if r9 == 0x0 goto pc+3
55: (79) r8 = *(u64 *)(r9 +32)
56: (79) r9 = *(u64 *)(r9 +0)
57: (05) goto pc+1
58: (79) r8 = *(u64 *)(r9 +32)
Here r9 register was in-use so r8 is chosen as the temporary register.
In line 52 r8 is saved in temp variable and at line 54 restored in case
fullsock != 0. Finally we handle fullsock == 0 case by restoring at
line 58.
This adds a new macro SOCK_OPS_GET_SK it is almost possible to merge
this with SOCK_OPS_GET_FIELD, but I found the extra branch logic a
bit more confusing than just adding a new macro despite a bit of
duplicating code.
Fixes: 1314ef5611 ("bpf: export bpf_sock for BPF_PROG_TYPE_SOCK_OPS prog type")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Song Liu <songliubraving@fb.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/159718349653.4728.6559437186853473612.stgit@john-Precision-5820-Tower
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d7bf2ebebc2bd61ab95e2a8e33541ef282f303d4 ]
There are a couple of places in net/sched/ that check skb->protocol and act
on the value there. However, in the presence of VLAN tags, the value stored
in skb->protocol can be inconsistent based on whether VLAN acceleration is
enabled. The commit quoted in the Fixes tag below fixed the users of
skb->protocol to use a helper that will always see the VLAN ethertype.
However, most of the callers don't actually handle the VLAN ethertype, but
expect to find the IP header type in the protocol field. This means that
things like changing the ECN field, or parsing diffserv values, stops
working if there's a VLAN tag, or if there are multiple nested VLAN
tags (QinQ).
To fix this, change the helper to take an argument that indicates whether
the caller wants to skip the VLAN tags or not. When skipping VLAN tags, we
make sure to skip all of them, so behaviour is consistent even in QinQ
mode.
To make the helper usable from the ECN code, move it to if_vlan.h instead
of pkt_sched.h.
v3:
- Remove empty lines
- Move vlan variable definitions inside loop in skb_protocol()
- Also use skb_protocol() helper in IP{,6}_ECN_decapsulate() and
bpf_skb_ecn_set_ce()
v2:
- Use eth_type_vlan() helper in skb_protocol()
- Also fix code that reads skb->protocol directly
- Change a couple of 'if/else if' statements to switch constructs to avoid
calling the helper twice
Reported-by: Ilya Ponetayev <i.ponetaev@ndmsystems.com>
Fixes: d8b9605d26 ("net: sched: fix skb->protocol use in case of accelerated vlan path")
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0f5d82f187e1beda3fe7295dfc500af266a5bd80 ]
Added a check in the switch case on start_header that checks for
the existence of the header, and in the case that MAC is not set
and the caller requests for MAC, -EFAULT. If the caller requests
for NET then MAC's existence is completely ignored.
There is no function to check NET header's existence and as far
as cgroup_skb/egress is concerned it should always be set.
Removed for ptr >= the start of header, considering offset is
bounded unsigned and should always be true. len <= end - mac is
redundant to ptr + len <= end.
Fixes: 3eee1f75f2 ("bpf: fix bpf_skb_load_bytes_relative pkt length check")
Signed-off-by: YiFei Zhu <zhuyifei@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Stanislav Fomichev <sdf@google.com>
Link: https://lore.kernel.org/bpf/76bb820ddb6a95f59a772ecbd8c8a336f646b362.1591812755.git.zhuyifei@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3e104c23816220919ea1b3fd93fabe363c67c484 ]
When sk_msg_pop() is called where the pop operation is working on
the end of a sge element and there is no additional trailing data
and there _is_ data in front of pop, like the following case,
|____________a_____________|__pop__|
We have out of order operations where we incorrectly set the pop
variable so that instead of zero'ing pop we incorrectly leave it
untouched, effectively. This can cause later logic to shift the
buffers around believing it should pop extra space. The result is
we have 'popped' more data then we expected potentially breaking
program logic.
It took us a while to hit this case because typically we pop headers
which seem to rarely be at the end of a scatterlist elements but
we can't rely on this.
Fixes: 7246d8ed4d ("bpf: helper to pop data from messages")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/158861288359.14306.7654891716919968144.stgit@john-Precision-5820-Tower
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0a29275b6300f39f78a87f2038bbfe5bdbaeca47 ]
A negative value should be returned if map->map_type is invalid
although that is impossible now, but if we run into such situation
in future, then xdpbuff could be leaked.
Daniel Borkmann suggested:
-EBADRQC should be returned to stay consistent with generic XDP
for the tracepoint output and not to be confused with -EOPNOTSUPP
from other locations like dev_map_enqueue() when ndo_xdp_xmit is
missing and such.
Suggested-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/1578618277-18085-1-git-send-email-lirongqing@baidu.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 2e012c74823629d9db27963c79caa3f5b2010746 upstream.
It's possible to leak time wait and request sockets via the following
BPF pseudo code:
sk = bpf_skc_lookup_tcp(...)
if (sk)
bpf_sk_release(sk)
If sk->sk_state is TCP_NEW_SYN_RECV or TCP_TIME_WAIT the refcount taken
by bpf_skc_lookup_tcp is not undone by bpf_sk_release. This is because
sk_flags is re-used for other data in both kinds of sockets. The check
!sock_flag(sk, SOCK_RCU_FREE)
therefore returns a bogus result. Check that sk_flags is valid by calling
sk_fullsock. Skip checking SOCK_RCU_FREE if we already know that sk is
not a full socket.
Fixes: edbf8c01de ("bpf: add skc_lookup_tcp helper")
Fixes: f7355a6c04 ("bpf: Check sk_fullsock() before returning from bpf_sk_lookup()")
Signed-off-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20200110132336.26099-1-lmb@cloudflare.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cf21e9ba1eb86c9333ca5b05b2f1cc94021bcaef upstream.
Leaving an incorrect end mark in place when passing to crypto
layer will cause crypto layer to stop processing data before
all data is encrypted. To fix clear the end mark on push
data instead of expecting users of the helper to clear the
mark value after the fact.
This happens when we push data into the middle of a skmsg and
have room for it so we don't do a set of copies that already
clear the end flag.
Fixes: 6fff607e2f ("bpf: sk_msg program helper bpf_msg_push_data")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Song Liu <songliubraving@fb.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/bpf/20200111061206.8028-6-john.fastabend@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6562e29cf6f0ddd368657d97a8d484ffc30df5ef upstream.
In the push, pull, and pop helpers operating on skmsg objects to make
data writable or insert/remove data we use this bounds check to ensure
specified data is valid,
/* Bounds checks: start and pop must be inside message */
if (start >= offset + l || last >= msg->sg.size)
return -EINVAL;
The problem here is offset has already included the length of the
current element the 'l' above. So start could be past the end of
the scatterlist element in the case where start also points into an
offset on the last skmsg element.
To fix do the accounting slightly different by adding the length of
the previous entry to offset at the start of the iteration. And
ensure its initialized to zero so that the first iteration does
nothing.
Fixes: 604326b41a ("bpf, sockmap: convert to generic sk_msg interface")
Fixes: 6fff607e2f ("bpf: sk_msg program helper bpf_msg_push_data")
Fixes: 7246d8ed4d ("bpf: helper to pop data from messages")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Song Liu <songliubraving@fb.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/bpf/20200111061206.8028-5-john.fastabend@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5133498f4ad1123a5ffd4c08df6431dab882cc32 ]
Redirecting a packet from ingress to egress by using bpf_redirect
breaks if the egress interface has an fq qdisc installed. This is the same
problem as fixed in 'commit 8203e2d844 ("net: clear skb->tstamp in forwarding paths")
Clear skb->tstamp when redirecting into the egress path.
Fixes: 80b14dee2b ("net: Add a new socket option for a future transmit time.")
Fixes: fb420d5d91 ("tcp/fq: move back to CLOCK_MONOTONIC")
Signed-off-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/bpf/20191213180817.2510-1-lmb@cloudflare.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 031097d9e079e40dce401031d1012e83d80eaf01 ]
TLS 1.3 started using the entry at the end of the SG array
for chaining-in the single byte content type entry. This mostly
works:
[ E E E E E E . . ]
^ ^
start end
E < content type
/
[ E E E E E E C . ]
^ ^
start end
(Where E denotes a populated SG entry; C denotes a chaining entry.)
If the array is full, however, the end will point to the start:
[ E E E E E E E E ]
^
start
end
And we end up overwriting the start:
E < content type
/
[ C E E E E E E E ]
^
start
end
The sg array is supposed to be a circular buffer with start and
end markers pointing anywhere. In case where start > end
(i.e. the circular buffer has "wrapped") there is an extra entry
reserved at the end to chain the two halves together.
[ E E E E E E . . l ]
(Where l is the reserved entry for "looping" back to front.
As suggested by John, let's reserve another entry for chaining
SG entries after the main circular buffer. Note that this entry
has to be pointed to by the end entry so its position is not fixed.
Examples of full messages:
[ E E E E E E E E . l ]
^ ^
start end
<---------------.
[ E E . E E E E E E l ]
^ ^
end start
Now the end will always point to an unused entry, so TLS 1.3
can always use it.
Fixes: 130b392c6c ("net: tls: Add tls 1.3 support")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For the sake of tcp_poll(), there are few places where we fetch
sk->sk_sndbuf while this field can change from IRQ or other cpu.
We need to add READ_ONCE() annotations, and also make sure write
sides use corresponding WRITE_ONCE() to avoid store-tearing.
Note that other transports probably need similar fixes.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the sake of tcp_poll(), there are few places where we fetch
sk->sk_rcvbuf while this field can change from IRQ or other cpu.
We need to add READ_ONCE() annotations, and also make sure write
sides use corresponding WRITE_ONCE() to avoid store-tearing.
Note that other transports probably need similar fixes.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sock_rcvlowat() or int_sk_rcvlowat() might be called without the socket
lock for example from tcp_poll().
Use READ_ONCE() to document the fact that other cpus might change
sk->sk_rcvlowat under us and avoid KCSAN splats.
Use WRITE_ONCE() on write sides too.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Daniel Borkmann says:
====================
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Add the ability to use unaligned chunks in the AF_XDP umem. By
relaxing where the chunks can be placed, it allows to use an
arbitrary buffer size and place whenever there is a free
address in the umem. Helps more seamless DPDK AF_XDP driver
integration. Support for i40e, ixgbe and mlx5e, from Kevin and
Maxim.
2) Addition of a wakeup flag for AF_XDP tx and fill rings so the
application can wake up the kernel for rx/tx processing which
avoids busy-spinning of the latter, useful when app and driver
is located on the same core. Support for i40e, ixgbe and mlx5e,
from Magnus and Maxim.
3) bpftool fixes for printf()-like functions so compiler can actually
enforce checks, bpftool build system improvements for custom output
directories, and addition of 'bpftool map freeze' command, from Quentin.
4) Support attaching/detaching XDP programs from 'bpftool net' command,
from Daniel.
5) Automatic xskmap cleanup when AF_XDP socket is released, and several
barrier/{read,write}_once fixes in AF_XDP code, from Björn.
6) Relicense of bpf_helpers.h/bpf_endian.h for future libbpf
inclusion as well as libbpf versioning improvements, from Andrii.
7) Several new BPF kselftests for verifier precision tracking, from Alexei.
8) Several BPF kselftest fixes wrt endianess to run on s390x, from Ilya.
9) And more BPF kselftest improvements all over the place, from Stanislav.
10) Add simple BPF map op cache for nfp driver to batch dumps, from Jakub.
11) AF_XDP socket umem mapping improvements for 32bit archs, from Ivan.
12) Add BPF-to-BPF call and BTF line info support for s390x JIT, from Yauheni.
13) Small optimization in arm64 JIT to spare 1 insns for BPF_MOD, from Jerin.
14) Fix an error check in bpf_tcp_gen_syncookie() helper, from Petar.
15) Various minor fixes and cleanups, from Nathan, Masahiro, Masanari,
Peter, Wei, Yue.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If a SYN cookie is not issued by tcp_v#_gen_syncookie, then the return
value will be exactly 0, rather than <= 0. Let's change the check to
reflect that, especially since mss is an unsigned value and cannot be
negative.
Fixes: 70d6624431 ("bpf: add bpf_tcp_gen_syncookie helper")
Reported-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Petar Penkov <ppenkov@google.com>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
test_select_reuseport fails on s390 due to verifier rejecting
test_select_reuseport_kern.o with the following message:
; data_check.eth_protocol = reuse_md->eth_protocol;
18: (69) r1 = *(u16 *)(r6 +22)
invalid bpf_context access off=22 size=2
This is because on big-endian machines casts from __u32 to __u16 are
generated by referencing the respective variable as __u16 with an offset
of 2 (as opposed to 0 on little-endian machines).
The verifier already has all the infrastructure in place to allow such
accesses, it's just that they are not explicitly enabled for
eth_protocol field. Enable them for eth_protocol field by using
bpf_ctx_range instead of offsetof.
Ditto for ip_protocol, bind_inany and len, since they already allow
narrowing, and the same problem can arise when working with them.
Fixes: 2dbb9b9e6d ("bpf: Introduce BPF_PROG_TYPE_SK_REUSEPORT")
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Daniel Borkmann says:
====================
The following pull-request contains BPF updates for your *net-next* tree.
There is a small merge conflict in libbpf (Cc Andrii so he's in the loop
as well):
for (i = 1; i <= btf__get_nr_types(btf); i++) {
t = (struct btf_type *)btf__type_by_id(btf, i);
if (!has_datasec && btf_is_var(t)) {
/* replace VAR with INT */
t->info = BTF_INFO_ENC(BTF_KIND_INT, 0, 0);
<<<<<<< HEAD
/*
* using size = 1 is the safest choice, 4 will be too
* big and cause kernel BTF validation failure if
* original variable took less than 4 bytes
*/
t->size = 1;
*(int *)(t+1) = BTF_INT_ENC(0, 0, 8);
} else if (!has_datasec && kind == BTF_KIND_DATASEC) {
=======
t->size = sizeof(int);
*(int *)(t + 1) = BTF_INT_ENC(0, 0, 32);
} else if (!has_datasec && btf_is_datasec(t)) {
>>>>>>> 72ef80b5ee
/* replace DATASEC with STRUCT */
Conflict is between the two commits 1d4126c4e1 ("libbpf: sanitize VAR to
conservative 1-byte INT") and b03bc6853c ("libbpf: convert libbpf code to
use new btf helpers"), so we need to pick the sanitation fixup as well as
use the new btf_is_datasec() helper and the whitespace cleanup. Looks like
the following:
[...]
if (!has_datasec && btf_is_var(t)) {
/* replace VAR with INT */
t->info = BTF_INFO_ENC(BTF_KIND_INT, 0, 0);
/*
* using size = 1 is the safest choice, 4 will be too
* big and cause kernel BTF validation failure if
* original variable took less than 4 bytes
*/
t->size = 1;
*(int *)(t + 1) = BTF_INT_ENC(0, 0, 8);
} else if (!has_datasec && btf_is_datasec(t)) {
/* replace DATASEC with STRUCT */
[...]
The main changes are:
1) Addition of core parts of compile once - run everywhere (co-re) effort,
that is, relocation of fields offsets in libbpf as well as exposure of
kernel's own BTF via sysfs and loading through libbpf, from Andrii.
More info on co-re: http://vger.kernel.org/bpfconf2019.html#session-2
and http://vger.kernel.org/lpc-bpf2018.html#session-2
2) Enable passing input flags to the BPF flow dissector to customize parsing
and allowing it to stop early similar to the C based one, from Stanislav.
3) Add a BPF helper function that allows generating SYN cookies from XDP and
tc BPF, from Petar.
4) Add devmap hash-based map type for more flexibility in device lookup for
redirects, from Toke.
5) Improvements to XDP forwarding sample code now utilizing recently enabled
devmap lookups, from Jesper.
6) Add support for reporting the effective cgroup progs in bpftool, from Jakub
and Takshak.
7) Fix reading kernel config from bpftool via /proc/config.gz, from Peter.
8) Fix AF_XDP umem pages mapping for 32 bit architectures, from Ivan.
9) Follow-up to add two more BPF loop tests for the selftest suite, from Alexei.
10) Add perf event output helper also for other skb-based program types, from Allan.
11) Fix a co-re related compilation error in selftests, from Yonghong.
====================
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
This helper function allows BPF programs to try to generate SYN
cookies, given a reference to a listener socket. The function works
from XDP and with an skb context since bpf_skc_lookup_tcp can lookup a
socket in both cases.
Signed-off-by: Petar Penkov <ppenkov@google.com>
Suggested-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
A common pattern when using xdp_redirect_map() is to create a device map
where the lookup key is simply ifindex. Because device maps are arrays,
this leaves holes in the map, and the map has to be sized to fit the
largest ifindex, regardless of how many devices actually are actually
needed in the map.
This patch adds a second type of device map where the key is looked up
using a hashmap, instead of being used as an array index. This allows maps
to be densely packed, so they can be smaller.
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Acked-by: Yonghong Song <yhs@fb.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Neal reported incorrect use of ns_capable() from bpf hook.
bpf_setsockopt(...TCP_CONGESTION...)
-> tcp_set_congestion_control()
-> ns_capable(sock_net(sk)->user_ns, CAP_NET_ADMIN)
-> ns_capable_common()
-> current_cred()
-> rcu_dereference_protected(current->cred, 1)
Accessing 'current' in bpf context makes no sense, since packets
are processed from softirq context.
As Neal stated : The capability check in tcp_set_congestion_control()
was written assuming a system call context, and then was reused from
a BPF call site.
The fix is to add a new parameter to tcp_set_congestion_control(),
so that the ns_capable() call is only performed under the right
context.
Fixes: 91b5b21c7c ("bpf: Add support for changing congestion control")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Lawrence Brakmo <brakmo@fb.com>
Reported-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Lawrence Brakmo <brakmo@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add explicit check for u64 loads of user_ip6 and msg_src_ip6 and
update the comment.
Cc: Yonghong Song <yhs@fb.com>
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Rename bpf_ctx_wide_store_ok to bpf_ctx_wide_access_ok to indicate
that it can be used for both loads and stores.
Cc: Yonghong Song <yhs@fb.com>
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Since commit cd17d77705 ("bpf/tools: sync bpf.h") clang decided
that it can do a single u64 store into user_ip6[2] instead of two
separate u32 ones:
# 17: (18) r2 = 0x100000000000000
# ; ctx->user_ip6[2] = bpf_htonl(DST_REWRITE_IP6_2);
# 19: (7b) *(u64 *)(r1 +16) = r2
# invalid bpf_context access off=16 size=8
>From the compiler point of view it does look like a correct thing
to do, so let's support it on the kernel side.
Credit to Andrii Nakryiko for a proper implementation of
bpf_ctx_wide_store_ok.
Cc: Andrii Nakryiko <andriin@fb.com>
Cc: Yonghong Song <yhs@fb.com>
Fixes: cd17d77705 ("bpf/tools: sync bpf.h")
Reported-by: kernel test robot <rong.a.chen@intel.com>
Acked-by: Yonghong Song <yhs@fb.com>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
We've added bpf_tcp_sock member to bpf_sock_ops and don't expect
any new tcp_sock fields in bpf_sock_ops. Let's remove
CONVERT_COMMON_TCP_SOCK_FIELDS so bpf_tcp_sock can be independently
extended.
Cc: Eric Dumazet <edumazet@google.com>
Cc: Priyaranjan Jha <priyarjha@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
The bpf_redirect_map() helper used by XDP programs doesn't return any
indication of whether it can successfully redirect to the map index it was
given. Instead, BPF programs have to track this themselves, leading to
programs using duplicate maps to track which entries are populated in the
devmap.
This patch fixes this by moving the map lookup into the bpf_redirect_map()
helper, which makes it possible to return failure to the eBPF program. The
lower bits of the flags argument is used as the return code, which means
that existing users who pass a '0' flag argument will get XDP_ABORTED.
With this, a BPF program can check the return code from the helper call and
react by, for instance, substituting a different redirect. This works for
any type of map used for redirect.
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
The bpf_redirect_info struct has an 'ifindex' member which was named back
when the redirects could only target egress interfaces. Now that we can
also redirect to sockets and CPUs, this is a bit misleading, so rename the
member to tgt_index.
Reorder the struct members so we can have 'tgt_index' and 'tgt_value' next
to each other in a subsequent patch.
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
The socket map uses a linked list instead of a bitmap to keep track of
which entries to flush. Do the same for devmap and cpumap, as this means we
don't have to care about the map index when enqueueing things into the
map (and so we can cache the map lookup).
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Implement new BPF_PROG_TYPE_CGROUP_SOCKOPT program type and
BPF_CGROUP_{G,S}ETSOCKOPT cgroup hooks.
BPF_CGROUP_SETSOCKOPT can modify user setsockopt arguments before
passing them down to the kernel or bypass kernel completely.
BPF_CGROUP_GETSOCKOPT can can inspect/modify getsockopt arguments that
kernel returns.
Both hooks reuse existing PTR_TO_PACKET{,_END} infrastructure.
The buffer memory is pre-allocated (because I don't think there is
a precedent for working with __user memory from bpf). This might be
slow to do for each {s,g}etsockopt call, that's why I've added
__cgroup_bpf_prog_array_is_empty that exits early if there is nothing
attached to a cgroup. Note, however, that there is a race between
__cgroup_bpf_prog_array_is_empty and BPF_PROG_RUN_ARRAY where cgroup
program layout might have changed; this should not be a problem
because in general there is a race between multiple calls to
{s,g}etsocktop and user adding/removing bpf progs from a cgroup.
The return code of the BPF program is handled as follows:
* 0: EPERM
* 1: success, continue with next BPF program in the cgroup chain
v9:
* allow overwriting setsockopt arguments (Alexei Starovoitov):
* use set_fs (same as kernel_setsockopt)
* buffer is always kzalloc'd (no small on-stack buffer)
v8:
* use s32 for optlen (Andrii Nakryiko)
v7:
* return only 0 or 1 (Alexei Starovoitov)
* always run all progs (Alexei Starovoitov)
* use optval=0 as kernel bypass in setsockopt (Alexei Starovoitov)
(decided to use optval=-1 instead, optval=0 might be a valid input)
* call getsockopt hook after kernel handlers (Alexei Starovoitov)
v6:
* rework cgroup chaining; stop as soon as bpf program returns
0 or 2; see patch with the documentation for the details
* drop Andrii's and Martin's Acked-by (not sure they are comfortable
with the new state of things)
v5:
* skip copy_to_user() and put_user() when ret == 0 (Martin Lau)
v4:
* don't export bpf_sk_fullsock helper (Martin Lau)
* size != sizeof(__u64) for uapi pointers (Martin Lau)
* offsetof instead of bpf_ctx_range when checking ctx access (Martin Lau)
v3:
* typos in BPF_PROG_CGROUP_SOCKOPT_RUN_ARRAY comments (Andrii Nakryiko)
* reverse christmas tree in BPF_PROG_CGROUP_SOCKOPT_RUN_ARRAY (Andrii
Nakryiko)
* use __bpf_md_ptr instead of __u32 for optval{,_end} (Martin Lau)
* use BPF_FIELD_SIZEOF() for consistency (Martin Lau)
* new CG_SOCKOPT_ACCESS macro to wrap repeated parts
v2:
* moved bpf_sockopt_kern fields around to remove a hole (Martin Lau)
* aligned bpf_sockopt_kern->buf to 8 bytes (Martin Lau)
* bpf_prog_array_is_empty instead of bpf_prog_array_length (Martin Lau)
* added [0,2] return code check to verifier (Martin Lau)
* dropped unused buf[64] from the stack (Martin Lau)
* use PTR_TO_SOCKET for bpf_sockopt->sk (Martin Lau)
* dropped bpf_target_off from ctx rewrites (Martin Lau)
* use return code for kernel bypass (Martin Lau & Andrii Nakryiko)
Cc: Andrii Nakryiko <andriin@fb.com>
Cc: Martin Lau <kafai@fb.com>
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2019-06-19
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) new SO_REUSEPORT_DETACH_BPF setsocktopt, from Martin.
2) BTF based map definition, from Andrii.
3) support bpf_map_lookup_elem for xskmap, from Jonathan.
4) bounded loops and scalar precision logic in the verifier, from Alexei.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The bpf_ipv6_fib_lookup function should return BPF_FIB_LKUP_RET_FWD_DISABLED
when forwarding is disabled for the input device. However instead of checking
if forwarding is enabled on the input device, it checked the global
net->ipv6.devconf_all->forwarding flag. Change it to behave as expected.
Fixes: 87f5fc7e48 ("bpf: Provide helper to do forwarding lookups in kernel FIB table")
Signed-off-by: Anton Protopopov <a.s.protopopov@gmail.com>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
And let it use bpf_sk_storage_{get,delete} helpers to access socket
storage. Kernel context (struct bpf_sock_ops_kern) already has sk
member, so I just expose it to the BPF hooks. I use
PTR_TO_SOCKET_OR_NULL and return NULL in !is_fullsock case.
I also export bpf_tcp_sock to make it possible to access tcp socket stats.
Cc: Martin Lau <kafai@fb.com>
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
And let it use bpf_sk_storage_{get,delete} helpers to access socket
storage. Kernel context (struct bpf_sock_addr_kern) already has sk
member, so I just expose it to the BPF hooks. Using PTR_TO_SOCKET
instead of PTR_TO_SOCK_COMMON should be safe because the hook is
called on bind/connect.
Cc: Martin Lau <kafai@fb.com>
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Currently, the AF_XDP code uses a separate map in order to
determine if an xsk is bound to a queue. Instead of doing this,
have bpf_map_lookup_elem() return a xdp_sock.
Rearrange some xdp_sock members to eliminate structure holes.
Remove selftest - will be added back in later patch.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Daniel Borkmann says:
====================
pull-request: bpf 2019-06-07
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fix several bugs in riscv64 JIT code emission which forgot to clear high
32-bits for alu32 ops, from Björn and Luke with selftests covering all
relevant BPF alu ops from Björn and Jiong.
2) Two fixes for UDP BPF reuseport that avoid calling the program in case of
__udp6_lib_err and UDP GRO which broke reuseport_select_sock() assumption
that skb->data is pointing to transport header, from Martin.
3) Two fixes for BPF sockmap: a use-after-free from sleep in psock's backlog
workqueue, and a missing restore of sk_write_space when psock gets dropped,
from Jakub and John.
4) Fix unconnected UDP sendmsg hook API which is insufficient as-is since it
breaks standard applications like DNS if reverse NAT is not performed upon
receive, from Daniel.
5) Fix an out-of-bounds read in __bpf_skc_lookup which in case of AF_INET6
fails to verify that the length of the tuple is long enough, from Lorenz.
6) Fix libbpf's libbpf__probe_raw_btf to return an fd instead of 0/1 (for
{un,}successful probe) as that is expected to be propagated as an fd to
load_sk_storage_btf() and thus closing the wrong descriptor otherwise,
from Michal.
7) Fix bpftool's JSON output for the case when a lookup fails, from Krzesimir.
8) Minor misc fixes in docs, samples and selftests, from various others.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Some ISDN files that got removed in net-next had some changes
done in mainline, take the removals.
Signed-off-by: David S. Miller <davem@davemloft.net>
