[ Upstream commit 66cce9e73ec61967ed1f97f30cee79bd9a2bb7ee ]
When a remote usb device is attached to the local Virtual USB
Host Controller Root Hub port, the bound device driver may send
a port reset command.
vhci_hcd accepts port resets only when the device doesn't have
port address assigned to it. When reset happens device is in
assigned/used state and vhci_hcd rejects it leaving the port in
a stuck state.
This problem was found when a blue-tooth or xbox wireless dongle
was passed through using usbip.
A few drivers reset the port during probe including mt76 driver
specific to this bug report. Fix the problem with a change to
honor reset requests when device is in used state (VDEV_ST_USED).
Reported-and-tested-by: Michael <msbroadf@gmail.com>
Suggested-by: Michael <msbroadf@gmail.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/20210819225937.41037-1-skhan@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7c75bde329d7e2a93cf86a5c15c61f96f1446cdc ]
If IRQ occurs between calling dsps_setup_optional_vbus_irq()
and dsps_create_musb_pdev(), then null pointer dereference occurs
since glue->musb wasn't initialized yet.
The patch puts initializing of neccesery data before registration
of the interrupt handler.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Nadezda Lutovinova <lutovinova@ispras.ru>
Link: https://lore.kernel.org/r/20210819163323.17714-1-lutovinova@ispras.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2847c46c61486fd8bca9136a6e27177212e78c69 ]
This reverts commit 5d5323a6f3625f101dbfa94ba3ef7706cce38760.
That commit effectively disabled Intel host initiated U1/U2 lpm for devices
with periodic endpoints.
Before that commit we disabled host initiated U1/U2 lpm if the exit latency
was larger than any periodic endpoint service interval, this is according
to xhci spec xhci 1.1 specification section 4.23.5.2
After that commit we incorrectly checked that service interval was smaller
than U1/U2 inactivity timeout. This is not relevant, and can't happen for
Intel hosts as previously set U1/U2 timeout = 105% * service interval.
Patch claimed it solved cases where devices can't be enumerated because of
bandwidth issues. This might be true but it's a side effect of accidentally
turning off lpm.
exit latency calculations have been revised since then
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210820123503.2605901-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e5d6a7c6cfae9e714a0e8ff64facd1ac68a784c6 ]
If wIndex is 0 (and it often is), these calculations underflow and
UBSAN complains, here resolve this by not decrementing the index when
it is equal to 0, this copies the solution from commit 85e3990bea
("USB: EHCI: avoid undefined pointer arithmetic and placate UBSAN")
Reported-by: Zhipeng Wang <zhipeng.wang_1@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Link: https://lore.kernel.org/r/1624004938-2399-1-git-send-email-jun.li@nxp.com
Signed-off-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bcacbf06c891374e7fdd7b72d11cda03b0269b43 ]
Currently the composite driver encodes the MaxPower field of
the configuration descriptor by reading the c->MaxPower of the
usb_configuration only if it is non-zero, otherwise it falls back
to using the value hard-coded in CONFIG_USB_GADGET_VBUS_DRAW.
However, there are cases when a configuration must explicitly set
bMaxPower to 0, particularly if its bmAttributes also has the
Self-Powered bit set, which is a valid combination.
This is specifically called out in the USB PD specification section
9.1, in which a PDUSB device "shall report zero in the bMaxPower
field after negotiating a mutually agreeable Contract", and also
verified by the USB Type-C Functional Test TD.4.10.2 Sink Power
Precedence Test.
The fix allows the c->MaxPower to be used for encoding the bMaxPower
even if it is 0, if the self-powered bit is also set. An example
usage of this would be for a ConfigFS gadget to be dynamically
updated by userspace when the Type-C connection is determined to be
operating in Power Delivery mode.
Co-developed-by: Ronak Vijay Raheja <rraheja@codeaurora.org>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Ronak Vijay Raheja <rraheja@codeaurora.org>
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Link: https://lore.kernel.org/r/20210720080907.30292-1-jackp@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 61136a12cbed234374ec6f588af57c580b20b772 ]
mv_ehci_enable() did not disable and unprepare clocks in case of
failures of phy_init(). Besides, it did not take into account failures
of ehci_clock_enable() (in effect, failures of clk_prepare_enable()).
The patch fixes both issues and gets rid of redundant wrappers around
clk_prepare_enable() and clk_disable_unprepare() to simplify this a bit.
Found by Linux Driver Verification project (linuxtesting.org).
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Link: https://lore.kernel.org/r/20210708083056.21543-1-novikov@ispras.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8ae01239609b29ec2eff55967c8e0fe3650cfa09 ]
f_ncm tx timeout can call us with null skb to flush
a pending frame. In this case skb is NULL to begin
with but ceases to be null after dev->wrap() completes.
In such a case in->maxpacket will be read, even though
we've failed to check that 'in' is not NULL.
Though I've never observed this fail in practice,
however the 'flush operation' simply does not make sense with
a null usb IN endpoint - there's nowhere to flush to...
(note that we're the gadget/device, and IN is from the point
of view of the host, so here IN actually means outbound...)
Cc: Brooke Basile <brookebasile@gmail.com>
Cc: "Bryan O'Donoghue" <bryan.odonoghue@linaro.org>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Link: https://lore.kernel.org/r/20210701114834.884597-6-zenczykowski@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 091cb2f782f32ab68c6f5f326d7868683d3d4875 ]
We should acquire the actual_length of an iso packet
from the iTD directly using FOTG210_ITD_LENGTH() macro.
Signed-off-by: Kelly Devilliv <kelly.devilliv@gmail.com>
Link: https://lore.kernel.org/r/20210627125747.127646-4-kelly.devilliv@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c2e898764245c852bc8ee4857613ba4f3a6d761d ]
Now that usb_endpoint_maxp() only returns the lowest
11 bits from wMaxPacketSize, we should make use of the
usb_endpoint_* helpers instead and remove the unnecessary
max_packet()/hb_mult() macro.
Signed-off-by: Kelly Devilliv <kelly.devilliv@gmail.com>
Link: https://lore.kernel.org/r/20210627125747.127646-3-kelly.devilliv@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d2f42e09393c774ab79088d8e3afcc62b3328fc9 ]
If no suitable DMA configuration is available, a previous 'bdc_phy_init()'
call must be undone by a corresponding 'bdc_phy_exit()' call.
Branch to the existing error handling path instead of returning
directly.
Fixes: cc29d4f677 ("usb: bdc: Add support for USB phy")
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/0c5910979f39225d5d8fe68c9ab1c147c68ddee1.1629314734.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4720f1bf4ee4a784d9ece05420ba33c9222a3004 ]
ehci_orion_drv_probe() did not account for possible errors of
clk_prepare_enable() that in particular could cause invocation of
clk_disable_unprepare() on clocks that were not prepared/enabled yet,
e.g. in remove or on handling errors of usb_add_hcd() in probe. Though,
there were several patches fixing different issues with clocks in this
driver, they did not solve this problem.
Add handling of errors of clk_prepare_enable() in ehci_orion_drv_probe()
to avoid calls of clk_disable_unprepare() without previous successful
invocation of clk_prepare_enable().
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: 8c869edaee ("ARM: Orion: EHCI: Add support for enabling clocks")
Co-developed-by: Kirill Shilimanov <kirill.shilimanov@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Signed-off-by: Kirill Shilimanov <kirill.shilimanov@huawei.com>
Link: https://lore.kernel.org/r/20210825170902.11234-1-novikov@ispras.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2af0c5ffadaf9d13eca28409d4238b4e672942d3 ]
If IRQ occurs between calling request_irq() and mv_u3d_eps_init(),
then null pointer dereference occurs since u3d->eps[] wasn't
initialized yet but used in mv_u3d_nuke().
The patch puts registration of the interrupt handler after
initializing of neccesery data.
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: 90fccb529d ("usb: gadget: Gadget directory cleanup - group UDC drivers")
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Nadezda Lutovinova <lutovinova@ispras.ru>
Link: https://lore.kernel.org/r/20210818141247.4794-1-lutovinova@ispras.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0d45a1373e669880b8beaecc8765f44cb0241e47 ]
The driver neglects to check the result of platform_get_irq()'s call and
blithely passes the negative error codes to request_threaded_irq() (which
takes *unsigned* IRQ #), causing it to fail with -EINVAL, overriding an
original error code. Stop calling request_threaded_irq() with the invalid
IRQ #s.
Fixes: 9ba96ae507 ("usb: omap1: Tahvo USB transceiver driver")
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/8280d6a4-8e9a-7cfe-1aa9-db586dc9afdf@omp.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4ac5132e8a4300637a2da8f5d6bc7650db735b8a ]
The driver neglects to check the result of platform_get_irq()'s call and
blithely passes the negative error codes to usb_add_hcd() (which takes
*unsigned* IRQ #), causing request_irq() that it calls to fail with
-EINVAL, overriding an original error code. Stop calling usb_add_hcd()
with the invalid IRQ #s.
Fixes: 78c73414f4 ("USB: ohci: add support for tmio-ohci cell")
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/402e1a45-a0a4-0e08-566a-7ca1331506b1@omp.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cea45a3bd2dd4d9c35581328f571afd32b3c9f48 ]
soc_device_match() is intended as a last resort, to handle e.g. quirks
that cannot be handled by matching based on a compatible value.
As the device nodes for the Renesas USB 3.0 Peripheral Controller on
R-Car E3 and RZ/G2E do have SoC-specific compatible values, the latter
can and should be used to match against these devices.
This also fixes support for the USB 3.0 Peripheral Controller on the
R-Car E3e (R8A779M6) SoC, which is a different grading of the R-Car E3
(R8A77990) SoC, using the same SoC-specific compatible value.
Fixes: 30025efa8b ("usb: gadget: udc: renesas_usb3: add support for r8a77990")
Fixes: 546970fdab ("usb: gadget: udc: renesas_usb3: add support for r8a774c0")
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/760981fb4cd110d7cbfc9dcffa365e7c8b25c6e5.1628696960.git.geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0881e22c06e66af0b64773c91c8868ead3d01aa1 ]
The driver neglects to check the result of platform_get_irq()'s calls and
blithely passes the negative error codes to request_threaded_irq() (which
takes *unsigned* IRQ #), causing them both to fail with -EINVAL, overriding
an original error code. Stop calling request_threaded_irq() with the
invalid IRQ #s.
Fixes: c33fad0c37 ("usb: otg: Adding twl6030-usb transceiver driver for OMAP4430")
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/9507f50b-50f1-6dc4-f57c-3ed4e53a1c25@omp.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ecc2f30dbb25969908115c81ec23650ed982b004 ]
The driver neglects to check the result of platform_get_irq()'s call and
blithely passes the negative error codes to request_irq() (which takes
*unsigned* IRQ #), causing it to fail with -EINVAL, overriding an original
error code. Stop calling request_irq() with the invalid IRQ #s.
Fixes: 0807c500a1 ("USB: add Freescale USB OTG Transceiver driver")
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/b0a86089-8b8b-122e-fd6d-73e8c2304964@omp.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 50855c31573b02963f0aa2aacfd4ea41c31ae0e0 ]
The driver neglects to check the result of platform_get_irq()'s call and
blithely passes the negative error codes to devm_request_irq() (which takes
*unsigned* IRQ #), causing it to fail with -EINVAL, overriding an original
error code. Stop calling devm_request_irq() with the invalid IRQ #s.
Fixes: 8b2e76687b ("USB: AT91 UDC updates, mostly power management")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Acked-by: Felipe Balbi <balbi@kernel.org>
Link: https://lore.kernel.org/r/6654a224-739a-1a80-12f0-76d920f87b6c@omp.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit cbf286e8ef8337308c259ff5b9ce2e74d403be5a upstream.
Removes static char buffer usage in the following decode functions:
xhci_decode_trb()
xhci_decode_ptortsc()
Caller must provide a buffer to use.
In tracing use __get_str() as recommended to pass buffer.
Minor chanes are needed in xhci debugfs code as these functions are also
used there. Changes include moving XHCI_MSG_MAX definititon from
xhci-trace.h to xhci.h
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210820123503.2605901-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 44e4439d8f9f8d0e9da767d1f31e7c211081feca upstream.
usb_endpoint_maxp() returns actual max packet size, @mult will
always be zero, fix it by using usb_endpoint_maxp_mult() instead
to get mult.
Fixes: 4d79e042ed ("usb: mtu3: add support for usb3.1 IP")
Cc: stable@vger.kernel.org
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1628836253-7432-3-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 57f3ffdc11143f56f1314972fe86fe17a0dcde85 upstream.
According to the datasheet, "Upon the completion of FW Download,
there is no need to write or reload FW.". Otherwise, it's possible
to cause unexpected behaviors. So, adds such a condition.
Fixes: 4ac8918f3a ("usb: host: xhci-plat: add support for the R-Car H2 and M2 xHCI controllers")
Cc: stable@vger.kernel.org # v3.17+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20210827063227.81990-1-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 161a582bd1d8681095f158d11bc679a58f1d026b upstream.
clang static analysis reports this problem
mos7720.c:352:2: warning: Undefined or garbage value returned to caller
return d;
^~~~~~~~
In the parport_mos7715_read_data()'s call to read_mos_reg(), 'd' is
only set after the alloc block.
buf = kmalloc(1, GFP_KERNEL);
if (!buf)
return -ENOMEM;
Although the problem is reported in parport_most7715_read_data(),
none of the callee's of read_mos_reg() check the return status.
Make sure to clear the return-value buffer also on allocation failures.
Fixes: 0d130367ab ("USB: serial: mos7720: fix control-message error handling")
Signed-off-by: Tom Rix <trix@redhat.com>
Link: https://lore.kernel.org/r/20210111220904.1035957-1-trix@redhat.com
[ johan: only clear the buffer on errors, amend commit message ]
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 068fdad20454f815e61e6f6eb9f051a8b3120e88 ]
If the endpoint completion callback is call right after the ep_enabled flag
is cleared and before usb_ep_dequeue() is call, we could do a double free
on the request and the associated buffer.
Fix this by clearing ep_enabled after all the endpoint requests have been
dequeued.
Fixes: 7de8681be2cd ("usb: gadget: u_audio: Free requests only after callback")
Cc: stable <stable@vger.kernel.org>
Reported-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20210827092927.366482-1-jbrunet@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 4a1e25c0a029b97ea4a3d423a6392bfacc3b2e39 upstream.
During a USB cable disconnect, or soft disconnect scenario, a pending
SETUP transaction may not be completed, leading to the following
error:
dwc3 a600000.dwc3: timed out waiting for SETUP phase
If this occurs, then the entire pullup disable routine is skipped and
proper cleanup and halting of the controller does not complete.
Instead of returning an error (which is ignored from the UDC
perspective), allow the pullup disable routine to continue, which
will also handle disabling of EP0/1. This will end any active
transfers as well. Ensure to clear any delayed_status also, as the
timeout could happen within the STATUS stage.
Fixes: bb01473648 ("usb: dwc3: gadget: don't clear RUN/STOP when it's invalid to do so")
Cc: <stable@vger.kernel.org>
Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/20210825042855.7977-1-wcheng@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 51f1954ad853d01ba4dc2b35dee14d8490ee05a1 upstream.
We can't depend on the TRB's HWO bit to determine if the TRB ring is
"full". A TRB is only available when the driver had processed it, not
when the controller consumed and relinquished the TRB's ownership to the
driver. Otherwise, the driver may overwrite unprocessed TRBs. This can
happen when many transfer events accumulate and the system is slow to
process them and/or when there are too many small requests.
If a request is in the started_list, that means there is one or more
unprocessed TRBs remained. Check this instead of the TRB's HWO bit
whether the TRB ring is full.
Fixes: c4233573f6 ("usb: dwc3: gadget: prepare TRBs on update transfers too")
Cc: <stable@vger.kernel.org>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/e91e975affb0d0d02770686afc3a5b9eb84409f6.1629335416.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit df7b16d1c00ecb3da3a30c999cdb39f273c99a2f upstream.
This reverts commit 3c18e9baee0ef97510dcda78c82285f52626764b.
These devices do not appear to send a zero-length packet when the
transfer size is a multiple of the bulk-endpoint max-packet size. This
means that incoming data may not be processed by the driver until a
short packet is received or the receive buffer is full.
Revert back to using endpoint-sized receive buffers to avoid stalled
reads.
Reported-by: Paul Größel <pb.g@gmx.de>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=214131
Fixes: 3c18e9baee0e ("USB: serial: ch341: fix character loss at high transfer rates")
Cc: stable@vger.kernel.org
Cc: Willy Tarreau <w@1wt.eu>
Link: https://lore.kernel.org/r/20210824121926.19311-1-johan@kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 60dfe484cef45293e631b3a6e8995f1689818172 ]
The USB core has utility routines to retrieve various types of
descriptors. These routines will now provoke a WARN if they are asked
to retrieve 0 bytes (USB "receive" requests must not have zero
length), so avert this by checking the size argument at the start.
CC: Johan Hovold <johan@kernel.org>
Reported-and-tested-by: syzbot+7dbcd9ff34dc4ed45240@syzkaller.appspotmail.com
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20210607152307.GD1768031@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 26b75952ca0b8b4b3050adb9582c8e2f44d49687 upstream.
Kunpeng920's EHCI controller does not have SBRN register.
Reading the SBRN register when the controller driver is
initialized will get 0.
When rebooting the EHCI driver, ehci_shutdown() will be called.
if the sbrn flag is 0, ehci_shutdown() will return directly.
The sbrn flag being 0 will cause the EHCI interrupt signal to
not be turned off after reboot. this interrupt that is not closed
will cause an exception to the device sharing the interrupt.
Therefore, the EHCI controller of Kunpeng920 needs to skip
the read operation of the SBRN register.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Longfang Liu <liulongfang@huawei.com>
Link: https://lore.kernel.org/r/1617958081-17999-1-git-send-email-liulongfang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cb10f68ad8150f243964b19391711aaac5e8ff42 ]
If the device is already in the runtime suspended state, any call to
the pullup routine will issue a runtime resume on the DWC3 core
device. If the USB gadget is disabling the pullup, then avoid having
to issue a runtime resume, as DWC3 gadget has already been
halted/stopped.
This fixes an issue where the following condition occurs:
usb_gadget_remove_driver()
-->usb_gadget_disconnect()
-->dwc3_gadget_pullup(0)
-->pm_runtime_get_sync() -> ret = 0
-->pm_runtime_put() [async]
-->usb_gadget_udc_stop()
-->dwc3_gadget_stop()
-->dwc->gadget_driver = NULL
...
dwc3_suspend_common()
-->dwc3_gadget_suspend()
-->DWC3 halt/stop routine skipped, driver_data == NULL
This leads to a situation where the DWC3 gadget is not properly
stopped, as the runtime resume would have re-enabled EP0 and event
interrupts, and since we avoided the DWC3 gadget suspend, these
resources were never disabled.
Fixes: 77adb8bdf422 ("usb: dwc3: gadget: Allow runtime suspend if UDC unbinded")
Cc: stable <stable@vger.kernel.org>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/1628058245-30692-1-git-send-email-wcheng@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8212937305f84ef73ea81036dafb80c557583d4b ]
Current sequence utilizes dwc3_gadget_disable_irq() alongside
synchronize_irq() to ensure that no further DWC3 events are generated.
However, the dwc3_gadget_disable_irq() API only disables device
specific events. Endpoint events can still be generated. Briefly
disable the interrupt line, so that the cleanup code can run to
prevent device and endpoint events. (i.e. __dwc3_gadget_stop() and
dwc3_stop_active_transfers() respectively)
Without doing so, it can lead to both the interrupt handler and the
pullup disable routine both writing to the GEVNTCOUNT register, which
will cause an incorrect count being read from future interrupts.
Fixes: ae7e86108b12 ("usb: dwc3: Stop active transfers before halting the controller")
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/1621571037-1424-1-git-send-email-wcheng@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5aef629704ad4d983ecf5c8a25840f16e45b6d59 ]
Ensure that dep->flags are cleared until after stop active transfers
is completed. Otherwise, the ENDXFER command will not be executed
during ep disable.
Fixes: f09ddcfcb8c5 ("usb: dwc3: gadget: Prevent EP queuing while stopping transfers")
Cc: stable <stable@vger.kernel.org>
Reported-and-tested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/1616610664-16495-1-git-send-email-wcheng@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f09ddcfcb8c569675066337adac2ac205113471f ]
In the situations where the DWC3 gadget stops active transfers, once
calling the dwc3_gadget_giveback(), there is a chance where a function
driver can queue a new USB request in between the time where the dwc3
lock has been released and re-aquired. This occurs after we've already
issued an ENDXFER command. When the stop active transfers continues
to remove USB requests from all dep lists, the newly added request will
also be removed, while controller still has an active TRB for it.
This can lead to the controller accessing an unmapped memory address.
Fix this by ensuring parameters to prevent EP queuing are set before
calling the stop active transfers API.
Fixes: ae7e86108b12 ("usb: dwc3: Stop active transfers before halting the controller")
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/1615507142-23097-1-git-send-email-wcheng@codeaurora.org
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a1383b3537a7bea1c213baa7878ccc4ecf4413b5 ]
usb_gadget_deactivate/usb_gadget_activate does not execute the UDC start
operation, which may leave EP0 disabled and event IRQs disabled when
re-activating the function. Move the enabling/disabling of USB EP0 and
device event IRQs to be performed in the pullup routine.
Fixes: ae7e86108b12 ("usb: dwc3: Stop active transfers before halting the controller")
Tested-by: Michael Tretter <m.tretter@pengutronix.de>
Cc: stable <stable@vger.kernel.org>
Reported-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/1609282837-21666-1-git-send-email-wcheng@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 77adb8bdf4227257e26b7ff67272678e66a0b250 ]
The DWC3 runtime suspend routine checks for the USB connected parameter to
determine if the controller can enter into a low power state. The
connected state is only set to false after receiving a disconnect event.
However, in the case of a device initiated disconnect (i.e. UDC unbind),
the controller is halted and a disconnect event is never generated. Set
the connected flag to false if issuing a device initiated disconnect to
allow the controller to be suspended.
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/1609283136-22140-2-git-send-email-wcheng@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ae7e86108b12351028fa7e8796a59f9b2d9e1774 ]
In the DWC3 databook, for a device initiated disconnect or bus reset, the
driver is required to send dependxfer commands for any pending transfers.
In addition, before the controller can move to the halted state, the SW
needs to acknowledge any pending events. If the controller is not halted
properly, there is a chance the controller will continue accessing stale or
freed TRBs and buffers.
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Reviewed-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bf88fef0b6f1488abeca594d377991171c00e52a upstream.
The HNP work can be re-scheduled while it's still in-fly. This results in
re-initialization of the busy work, resetting the hrtimer's list node of
the work and crashing kernel with null dereference within kernel/timer
once work's timer is expired. It's very easy to trigger this problem by
re-plugging USB cable quickly. Initialize HNP work only once to fix this
trouble.
Unable to handle kernel NULL pointer dereference at virtual address 00000126)
...
PC is at __run_timers.part.0+0x150/0x228
LR is at __next_timer_interrupt+0x51/0x9c
...
(__run_timers.part.0) from [<c0187a2b>] (run_timer_softirq+0x2f/0x50)
(run_timer_softirq) from [<c01013ad>] (__do_softirq+0xd5/0x2f0)
(__do_softirq) from [<c012589b>] (irq_exit+0xab/0xb8)
(irq_exit) from [<c0170341>] (handle_domain_irq+0x45/0x60)
(handle_domain_irq) from [<c04c4a43>] (gic_handle_irq+0x6b/0x7c)
(gic_handle_irq) from [<c0100b65>] (__irq_svc+0x65/0xac)
Cc: stable@vger.kernel.org
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20210717182134.30262-6-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fa20bada3f934e3b3e4af4c77e5b518cd5a282e5 upstream.
SET_IDLE value must be shifted 8 bits to the right to get duration.
This confirmed by USBCV test.
Fixes: afcff6dc690e ("usb: gadget: f_hid: added GET_IDLE and SET_IDLE handlers")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Maxim Devaev <mdevaev@gmail.com>
Link: https://lore.kernel.org/r/20210727185800.43796-1-mdevaev@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2867652e4766360adf14dfda3832455e04964f2a upstream.
Disconnecting and reconnecting the USB cable can lead to crashes
and a variety of kernel log spam.
The problem was found and reproduced on the Raspberry Pi [1]
and the original fix was created in Raspberry's own fork [2].
Link: https://github.com/raspberrypi/linux/issues/3870 [1]
Link: a6e47d5f4e [2]
Signed-off-by: Maxim Devaev <mdevaev@gmail.com>
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210723155928.210019-1-mdevaev@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit afcff6dc690e24d636a41fd4bee6057e7c70eebd upstream.
The USB HID standard declares mandatory support for GET_IDLE and SET_IDLE
requests for Boot Keyboard. Most hosts can handle their absence, but others
like some old/strange UEFIs and BIOSes consider this a critical error
and refuse to work with f_hid.
This primitive implementation of saving and returning idle is sufficient
to meet the requirements of the standard and these devices.
Acked-by: Felipe Balbi <balbi@kernel.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Maxim Devaev <mdevaev@gmail.com>
Link: https://lore.kernel.org/r/20210721180351.129450-1-mdevaev@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suguru Saito