[ Upstream commit 26cfc0dbe43aae60dc03af27077775244f26c167 ]
The function wait_for_completion_interruptible_timeout will return
-ERESTARTSYS immediately when receiving SIGKILL signal which is sent
by "jffs2_gcd_mtd" during umounting jffs2. This will break the SPI memory
operation because the data transmitting may begin before the command or
address transmitting completes. Use wait_for_completion_timeout to prevent
the process from being interruptible.
Fixes: 67dca5e580 ("spi: spi-mem: Add support for Zynq QSPI controller")
Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com>
Link: https://lore.kernel.org/r/20210826005930.20572-1-quanyang.wang@windriver.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 245ca2cc212bb2a078332ec99afbfbb202f44c2d ]
Use 50ms as default timeout value and the time clock is 32768HZ.
The original value of WDG_LOAD_VAL is not correct, so this patch
fixes it.
Fixes: ac17750120 ("spi: sprd: Add the support of restarting the system")
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Link: https://lore.kernel.org/r/20210826091549.2138125-2-zhang.lyra@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 976c1de1de147bb7f4e0d87482f375221c05aeaf ]
Depending on the DMA driver being used, the struct dma_slave_config may
need to be initialized to zero for the unused data.
For example, we have three DMA drivers using src_port_window_size and
dst_port_window_size. If these are left uninitialized, it can cause DMA
failures.
For spi-pic32, this is probably not currently an issue but is still good to
fix though.
Fixes: 1bcb9f8ceb ("spi: spi-pic32: Add PIC32 SPI master driver")
Cc: Purna Chandra Mandal <purna.mandal@microchip.com>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Cc: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210810081727.19491-2-tony@atomide.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 209ab223ad5b18e437289235e3bde12593b94ac4 ]
Depending on the DMA driver being used, the struct dma_slave_config may
need to be initialized to zero for the unused data.
For example, we have three DMA drivers using src_port_window_size and
dst_port_window_size. If these are left uninitialized, it can cause DMA
failures.
For spi-fsl-dspi, this is probably not currently an issue but is still
good to fix though.
Fixes: 90ba37033c ("spi: spi-fsl-dspi: Add DMA support for Vybrid")
Cc: Sanchayan Maity <maitysanchayan@gmail.com>
Cc: Vladimir Oltean <vladimir.oltean@nxp.com>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Cc: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20210810081727.19491-1-tony@atomide.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 8311ee2164c5cd1b63a601ea366f540eae89f10e upstream.
In meson_spicc_probe, the error handling code needs to clean up master
by calling spi_master_put, but the remove function does not have this
function call. This will lead to memory leak of spicc->master.
Reported-by: Dongliang Mu <mudongliangabcd@gmail.com>
Fixes: 454fa271bc4e("spi: Add Meson SPICC driver")
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Link: https://lore.kernel.org/r/20210720100116.1438974-1-mudongliangabcd@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 53ca18acbe645656132fb5a329833db711067e54 ]
The spi_imx->spi_bus_clk may be uninitialized and thus also zero in
mx51_ecspi_prepare_message(), which would lead to division by zero
in kernel. Since bitbang .setup_transfer callback which initializes
the spi_imx->spi_bus_clk is called after bitbang prepare_message
callback, iterate over all the transfers in spi_message, find the
one with lowest bus frequency, and use that bus frequency for the
delay calculation.
Note that it is not possible to move this CONFIGREG delay back into
the .setup_transfer callback, because that is invoked too late, after
the GPIO chipselects were already configured.
Fixes: 135cbd378eab ("spi: imx: mx51-ecspi: Reinstate low-speed CONFIGREG delay")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210726100102.5188-1-marex@denx.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 135cbd378eab336da15de9c84bbb22bf743b38a5 ]
Since 00b80ac935 ("spi: imx: mx51-ecspi: Move some initialisation to
prepare_message hook."), the MX51_ECSPI_CONFIG write no longer happens
in prepare_transfer hook, but rather in prepare_message hook, however
the MX51_ECSPI_CONFIG delay is still left in prepare_transfer hook and
thus has no effect. This leads to low bus frequency operation problems
described in 6fd8b8503a ("spi: spi-imx: Fix out-of-order CS/SCLK
operation at low speeds") again.
Move the MX51_ECSPI_CONFIG write delay into the prepare_message hook
as well, thus reinstating the low bus frequency fix.
Fixes: 00b80ac935 ("spi: imx: mx51-ecspi: Move some initialisation to prepare_message hook.")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210703022300.296114-1-marex@denx.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 0d5c3954b35eddff0da0436c31e8d721eceb7dc2 upstream.
Commit 3a70dd2d0503 ("spi: mediatek: fix fifo rx mode") claims that
fifo RX mode was never handled, and adds the presumably missing code
to the FIFO transfer function. However, the claim that receive data
was not handled is incorrect. It was handled as part of interrupt
handling after the transfer was complete. The code added with the above
mentioned commit reads data from the receive FIFO before the transfer
is started, which is wrong. This results in an actual transfer error
on a Hayato Chromebook.
Remove the code trying to handle receive data before the transfer is
started to fix the problem.
Fixes: 3a70dd2d0503 ("spi: mediatek: fix fifo rx mode")
Cc: Peter Hess <peter.hess@ph-home.de>
Cc: Frank Wunderlich <frank-w@public-files.de>
Cc: Tzung-Bi Shih <tzungbi@google.com>
Cc: Hsin-Yi Wang <hsinyi@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Hsin-Yi Wang <hsinyi@google.com>
Tested-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20210802030023.1748777-1-linux@roeck-us.net
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e4a5c19888a5f8a9390860ca493e643be58c8791 ]
In case of Full-Duplex mode, DXP flag is set when RXP and TXP flags are
set. But to avoid 2 different handlings, just add TXP and RXP flag in
the mask instead of DXP, and then keep the initial handling of TXP and
RXP events.
Also rephrase comment about EOTIE which is one of the interrupt enable
bits. It is not triggered by any event.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Reviewed-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/1625042723-661-3-git-send-email-alain.volmat@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 56912da7a68c8356df6a6740476237441b0b792a ]
The original implementation of RPM handling in probe() was mostly
correct, except it failed to call pm_runtime_get_*() to activate the
hardware. The subsequent fix, 734882a8bf ("spi: cadence: Correct
initialisation of runtime PM"), breaks the implementation further,
to the point where the system using this hard IP on ZynqMP hangs on
boot, because it accesses hardware which is gated off.
Undo 734882a8bf ("spi: cadence: Correct initialisation of runtime
PM") and instead add missing pm_runtime_get_noresume() and move the
RPM disabling all the way to the end of probe(). That makes ZynqMP
not hang on boot yet again.
Fixes: 734882a8bf ("spi: cadence: Correct initialisation of runtime PM")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Charles Keepax <ckeepax@opensource.cirrus.com>
Cc: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210716182133.218640-1-marex@denx.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3a70dd2d050331ee4cf5ad9d5c0a32d83ead9a43 ]
In FIFO mode were two problems:
- RX mode was never handled and
- in this case the tx_buf pointer was NULL and caused an exception
fix this by handling RX mode in mtk_spi_fifo_transfer
Fixes: a568231f46 ("spi: mediatek: Add spi bus for Mediatek MT8173")
Signed-off-by: Peter Hess <peter.hess@ph-home.de>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Link: https://lore.kernel.org/r/20210706121609.680534-1-linux@fw-web.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7999d2555c9f879d006ea8469d74db9cdb038af0 ]
Add pm_runtime calls in probe/probe error path and remove
in order to be consistent in all places in ordering and
ensure that pm_runtime is disabled prior to resources used
by the SPI controller.
This patch also fixes the 2 following warnings on driver remove:
WARNING: CPU: 0 PID: 743 at drivers/clk/clk.c:594 clk_core_disable_lock+0x18/0x24
WARNING: CPU: 0 PID: 743 at drivers/clk/clk.c:476 clk_unprepare+0x24/0x2c
Fixes: 038ac869c9 ("spi: stm32: add runtime PM support")
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Link: https://lore.kernel.org/r/1625646426-5826-2-git-send-email-alain.volmat@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0a454258febb73e4c60d7f5d9a02d1a8c64fdfb8 ]
dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.
By using dma_request_chan() directly the driver can support deferred
probing against DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191212135550.4634-10-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4df2f5e1372e9eec8f9e1b4a3025b9be23487d36 ]
When some drivers use spi to send data, spi_transfer->speed_hz is
not assigned. If spidev->max_speed_hz is not assigned as well, it
will cause an error in configuring the clock.
Add a check for these two values before configuring the clock. An
error will be returned when they are not assigned.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Link: https://lore.kernel.org/r/20210408103347.244313-2-xiaoning.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0d7993b234c9fad8cb6bec6adfaa74694ba85ecb ]
The current sun6i SPI implementation initializes the transfer too early,
resulting in SCK going high before the transfer. When using an additional
(gpio) chipselect with sun6i, the chipselect is asserted at a time when
clock is high, making the SPI transfer fail.
This is due to SUN6I_GBL_CTL_BUS_ENABLE being written into
SUN6I_GBL_CTL_REG at an early stage. Moving that to the transfer
function, hence, right before the transfer starts, mitigates that
problem.
Fixes: 3558fe900e (spi: sunxi: Add Allwinner A31 SPI controller driver)
Signed-off-by: Mirko Vogt <mirko-dev|linux@nanl.de>
Signed-off-by: Ralf Schlatterbeck <rsc@runtux.com>
Link: https://lore.kernel.org/r/20210614144507.y3udezjfbko7eavv@runtux.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e7a1a3abea373e41ba7dfe0fbc93cb79b6a3a529 ]
word_len should be checked in the omap1_spi100k_setup_transfer
function to see if it exceeds 32.
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Link: https://lore.kernel.org/r/1619695248-39045-1-git-send-email-tiantao6@hisilicon.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 026a1dc1af52742c5897e64a3431445371a71871 ]
pch_spi_set_tx() frees data->pkt_tx_buff on failure of kzalloc() for
data->pkt_rx_buff, but its caller, pch_spi_process_messages(), will
free data->pkt_tx_buff again. Set data->pkt_tx_buff to NULL after
kfree() to avoid double free.
Signed-off-by: Jay Fang <f.fangjian@huawei.com>
Link: https://lore.kernel.org/r/1620284888-65215-1-git-send-email-f.fangjian@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9e37a3ab0627011fb63875e9a93094b6fc8ddf48 ]
In function 'spi_test_run_iter': Value 'tx_buf' might be 'rx_buf'.
Signed-off-by: Jay Fang <f.fangjian@huawei.com>
Link: https://lore.kernel.org/r/1620629903-15493-5-git-send-email-f.fangjian@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0e793ba77c18382f08e440260fe72bc6fce2a3cb ]
Currently, the SPI core doesn't set the struct device fwnode pointer
when it creates a new SPI device. This means when the device is
registered the fwnode is NULL and the check in device_add which sets
the fwnode->dev pointer is skipped. This wasn't previously an issue,
however these two patches:
commit 4731210c09f5 ("gpiolib: Bind gpio_device to a driver to enable
fw_devlink=on by default")
commit ced2af419528 ("gpiolib: Don't probe gpio_device if it's not the
primary device")
Added some code to the GPIO core which relies on using that
fwnode->dev pointer to determine if a driver is bound to the fwnode
and if not bind a stub GPIO driver. This means the GPIO providers
behind SPI will get both the expected driver and this stub driver
causing the stub driver to fail if it attempts to request any pin
configuration. For example on my system:
madera-pinctrl madera-pinctrl: pin gpio5 already requested by madera-pinctrl; cannot claim for gpiochip3
madera-pinctrl madera-pinctrl: pin-4 (gpiochip3) status -22
madera-pinctrl madera-pinctrl: could not request pin 4 (gpio5) from group aif1 on device madera-pinctrl
gpio_stub_drv gpiochip3: Error applying setting, reverse things back
gpio_stub_drv: probe of gpiochip3 failed with error -22
The firmware node on the device created by the GPIO framework is set
through the of_node pointer hence things generally actually work,
however that fwnode->dev is never set, as the check was skipped at
device_add time. This fix appears to match how the I2C subsystem
handles the same situation.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210421101402.8468-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f422316c8e9d3c4aff3c56549dfb44a677d02f14 ]
Move the register operation after the clock enable, otherwise system
will stuck when this driver probe.
Fixes: 71d80563b076 ("spi: spi-nxp-fspi: fix fspi panic by unexpected interrupts")
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Link: https://lore.kernel.org/r/1623317073-25158-1-git-send-email-haibo.chen@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d38fa9a155b2829b7e2cfcf8a4171b6dd3672808 ]
In U-boot side, an issue has been encountered when QSPI source clock is
running at low frequency (24 MHz for example), waiting for TCF bit to be
set didn't ensure that all data has been send out the FIFO, we should also
wait that BUSY bit is cleared.
To prevent similar issue in kernel driver, we implement similar behavior
by always waiting BUSY bit to be cleared.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Link: https://lore.kernel.org/r/20210603073421.8441-1-patrice.chotard@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 13817d466eb8713a1ffd254f537402f091d48444 upstream.
Commit 571e31fa60 ("spi: bcm2835: Cache CS register value for
->prepare_message()") limited the number of slaves to 3 at compile-time.
The limitation was necessitated by a statically-sized array prepare_cs[]
in the driver private data which contains a per-slave register value.
The commit sought to enforce the limitation at run-time by setting the
controller's num_chipselect to 3: Slaves with a higher chipselect are
rejected by spi_add_device().
However the commit neglected that num_chipselect only limits the number
of *native* chipselects. If GPIO chipselects are specified in the
device tree for more than 3 slaves, num_chipselect is silently raised by
of_spi_get_gpio_numbers() and the result are out-of-bounds accesses to
the statically-sized array prepare_cs[].
As a bandaid fix which is backportable to stable, raise the number of
allowed slaves to 24 (which "ought to be enough for anybody"), enforce
the limitation on slave ->setup and revert num_chipselect to 3 (which is
the number of native chipselects supported by the controller).
An upcoming for-next commit will allow an arbitrary number of slaves.
Fixes: 571e31fa60 ("spi: bcm2835: Cache CS register value for ->prepare_message()")
Reported-by: Joe Burmeister <joe.burmeister@devtank.co.uk>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v5.4+
Cc: Phil Elwell <phil@raspberrypi.com>
Link: https://lore.kernel.org/r/75854affc1923309fde05e47494263bde73e5592.1621703210.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2ec6f20b33eb4f62ab90bdcd620436c883ec3af6 ]
Commit c7299fea6769 ("spi: Fix spi device unregister flow") changed the
SPI core's behavior if the ->setup() hook returns an error upon adding
an spi_device: Before, the ->cleanup() hook was invoked to free any
allocations that were made by ->setup(). With the commit, that's no
longer the case, so the ->setup() hook is expected to free the
allocations itself.
I've identified 5 drivers which depend on the old behavior and am fixing
them up hereinafter: spi-bitbang.c spi-fsl-spi.c spi-omap-uwire.c
spi-omap2-mcspi.c spi-pxa2xx.c
Importantly, ->setup() is not only invoked on spi_device *addition*:
It may subsequently be called to *change* SPI parameters. If changing
these SPI parameters fails, freeing memory allocations would be wrong.
That should only be done if the spi_device is finally destroyed.
I am therefore using a bool "initial_setup" in 4 of the affected drivers
to differentiate between the invocation on *adding* the spi_device and
any subsequent invocations: spi-bitbang.c spi-fsl-spi.c spi-omap-uwire.c
spi-omap2-mcspi.c
In spi-pxa2xx.c, it seems the ->setup() hook can only fail on spi_device
addition, not any subsequent calls. It therefore doesn't need the bool.
It's worth noting that 5 other drivers already perform a cleanup if the
->setup() hook fails. Before c7299fea6769, they caused a double-free
if ->setup() failed on spi_device addition. Since the commit, they're
fine. These drivers are: spi-mpc512x-psc.c spi-pl022.c spi-s3c64xx.c
spi-st-ssc4.c spi-tegra114.c
(spi-pxa2xx.c also already performs a cleanup, but only in one of
several error paths.)
Fixes: c7299fea6769 ("spi: Fix spi device unregister flow")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Saravana Kannan <saravanak@google.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> # pxa2xx
Link: https://lore.kernel.org/r/f76a0599469f265b69c371538794101fa37b5536.1622149321.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 27e7db56cf3dffd302bd7ddfacb1d405cf671a2a ]
When a spi device is unregistered and triggers a driver unbind, the
driver might need to access the spi device. So, don't have the
controller clean up the spi device before the driver is unbound. Clean
up the spi device after the driver is unbound.
Fixes: c7299fea6769 ("spi: Fix spi device unregister flow")
Reported-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Saravana Kannan <saravanak@google.com>
Tested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20210505164734.175546-1-saravanak@google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7907cad7d07e0055789ec0c534452f19dfe1fc80 ]
MODULE_DEVICE_TABLE is used to extract the device information out of the
driver and builds a table when being compiled. If using this macro,
kernel can find the driver if available when the device is plugged in,
and then loads that driver and initializes the device.
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Link: https://lore.kernel.org/r/20210512093534.243040-1-zhang.lyra@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c7299fea67696db5bd09d924d1f1080d894f92ef ]
When an SPI device is unregistered, the spi->controller->cleanup() is
called in the device's release callback. That's wrong for a couple of
reasons:
1. spi_dev_put() can be called before spi_add_device() is called. And
it's spi_add_device() that calls spi_setup(). This will cause clean()
to get called without the spi device ever being setup.
2. There's no guarantee that the controller's driver would be present by
the time the spi device's release function gets called.
3. It also causes "sleeping in atomic context" stack dump[1] when device
link deletion code does a put_device() on the spi device.
Fix these issues by simply moving the cleanup from the device release
callback to the actual spi_unregister_device() function.
[1] - https://lore.kernel.org/lkml/CAHp75Vc=FCGcUyS0v6fnxme2YJ+qD+Y-hQDQLa2JhWNON9VmsQ@mail.gmail.com/
Signed-off-by: Saravana Kannan <saravanak@google.com>
Link: https://lore.kernel.org/r/20210426235638.1285530-1-saravanak@google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 680ec0549a055eb464dce6ffb4bfb736ef87236e upstream.
'dspi_request_dma()' should be undone by a 'dspi_release_dma()' call in the
error handling path of the probe function, as already done in the remove
function
Fixes: 90ba37033c ("spi: spi-fsl-dspi: Add DMA support for Vybrid")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/d51caaac747277a1099ba8dea07acd85435b857e.1620587472.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8f96c434dfbc85ffa755d6634c8c1cb2233fcf24 upstream.
spi_geni_remove() accesses the driver's private data after calling
spi_unregister_master() even though that function releases the last
reference on the spi_master and thereby frees the private data.
Moreover, since commit 1a9e489e6128 ("spi: spi-geni-qcom: Use OPP API to
set clk/perf state"), spi_geni_probe() leaks the spi_master allocation
if the calls to dev_pm_opp_set_clkname() or dev_pm_opp_of_add_table()
fail.
Fix by switching over to the new devm_spi_alloc_master() helper which
keeps the private data accessible until the driver has unbound and also
avoids the spi_master leak on probe.
Fixes: 561de45f72 ("spi: spi-geni-qcom: Add SPI driver support for GENI based QUP")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: <stable@vger.kernel.org> # v4.20+: 5e844cc37a5c: spi: Introduce device-managed SPI controller allocation
Cc: <stable@vger.kernel.org> # v4.20+
Cc: Rajendra Nayak <rnayak@codeaurora.org>
Cc: Girish Mahadevan <girishm@codeaurora.org>
Link: https://lore.kernel.org/r/dfa1d8c41b8acdfad87ec8654cd124e6e3cb3f31.1607286887.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
[lukas: backport to v5.4.123]
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a03675497970a93fcf25d81d9d92a59c2d7377a7 ]
pm_runtime_get_sync will increment pm usage counter even it failed.
Forgetting to putting operation will result in reference leak here.
Fix it by replacing it with pm_runtime_resume_and_get to keep usage
counter balanced.
Fixes: 944c01a889 ("spi: lpspi: enable runtime pm for lpspi")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Li <wangli74@huawei.com>
Link: https://lore.kernel.org/r/20210409095430.29868-1-wangli74@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 794aaf01444d4e765e2b067cba01cc69c1c68ed9 ]
We can't rely on the contents of the devres list during
spi_unregister_controller(), as the list is already torn down at the
time we perform devres_find() for devm_spi_release_controller. This
causes devices registered with devm_spi_alloc_{master,slave}() to be
mistakenly identified as legacy, non-devm managed devices and have their
reference counters decremented below 0.
------------[ cut here ]------------
WARNING: CPU: 1 PID: 660 at lib/refcount.c:28 refcount_warn_saturate+0x108/0x174
[<b0396f04>] (refcount_warn_saturate) from [<b03c56a4>] (kobject_put+0x90/0x98)
[<b03c5614>] (kobject_put) from [<b0447b4c>] (put_device+0x20/0x24)
r4:b6700140
[<b0447b2c>] (put_device) from [<b07515e8>] (devm_spi_release_controller+0x3c/0x40)
[<b07515ac>] (devm_spi_release_controller) from [<b045343c>] (release_nodes+0x84/0xc4)
r5:b6700180 r4:b6700100
[<b04533b8>] (release_nodes) from [<b0454160>] (devres_release_all+0x5c/0x60)
r8:b1638c54 r7:b117ad94 r6:b1638c10 r5:b117ad94 r4:b163dc10
[<b0454104>] (devres_release_all) from [<b044e41c>] (__device_release_driver+0x144/0x1ec)
r5:b117ad94 r4:b163dc10
[<b044e2d8>] (__device_release_driver) from [<b044f70c>] (device_driver_detach+0x84/0xa0)
r9:00000000 r8:00000000 r7:b117ad94 r6:b163dc54 r5:b1638c10 r4:b163dc10
[<b044f688>] (device_driver_detach) from [<b044d274>] (unbind_store+0xe4/0xf8)
Instead, determine the devm allocation state as a flag on the
controller which is guaranteed to be stable during cleanup.
Fixes: 5e844cc37a5c ("spi: Introduce device-managed SPI controller allocation")
Signed-off-by: William A. Kennington III <wak@google.com>
Link: https://lore.kernel.org/r/20210407095527.2771582-1-wak@google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8d559a64f00b59af9cc02b803ff52f6e6880a651 ]
A call to spi_unregister_master() triggers calling remove()
for all the spi devices binded to the spi master.
Some spi device driver requires to "talk" with the spi device
during the remove(), e.g.:
- a LCD panel like drivers/gpu/drm/panel/panel-lg-lg4573.c
will turn off the backlighting sending a command over spi.
This implies that the spi master must be fully functional when
spi_unregister_master() is called, either if it is called
explicitly in the master's remove() code or implicitly by the
devres framework.
Devres calls devres_release_all() to release all the resources
"after" the remove() of the spi master driver (check code of
__device_release_driver() in drivers/base/dd.c).
If the spi master driver has an empty remove() then there would
be no issue; the devres_release_all() will release everything
in reverse order w.r.t. probe().
But if code in spi master driver remove() disables the spi or
makes it not functional (like in this spi-stm32), then devres
cannot be used safely for unregistering the spi master and the
binded spi devices.
Replace devm_spi_register_master() with spi_register_master()
and add spi_unregister_master() as first action in remove().
Fixes: dcbe0d84df ("spi: add driver for STM32 SPI controller")
Signed-off-by: Antonio Borneo <antonio.borneo@foss.st.com>
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Link: https://lore.kernel.org/r/1615545286-5395-1-git-send-email-alain.volmat@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cec77e0a249892ceb10061bf17b63f9fb111d870 ]
pm_runtime_get_sync will increment pm usage counter even it failed.
Forgetting to putting operation will result in reference leak here.
Fix it by replacing it with pm_runtime_resume_and_get to keep usage
counter balanced.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Li <wangli74@huawei.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20210409095458.29921-1-wangli74@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a23faea76d4cf5f75decb574491e66f9ecd707e7 ]
Call spi_master_get() holds the reference count to master device, thus
we need an additional spi_master_put() call to reduce the reference
count, otherwise we will leak a reference to master.
This commit fix it by removing the unnecessary spi_master_get().
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20210409082954.2906933-1-weiyongjun1@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9b844b087124c1538d05f40fda8a4fec75af55be ]
Call spi_master_get() holds the reference count to master device, thus
we need an additional spi_master_put() call to reduce the reference
count, otherwise we will leak a reference to master.
This commit fix it by removing the unnecessary spi_master_get().
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20210409082955.2907950-1-weiyongjun1@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ffb597b2bd3cd78b9bfb68f536743cd46dbb2cc4 ]
This removes the assignment of setup and cleanup functions for the ath79
target. Assigning the setup-method will lead to 'setup_transfer' not
being assigned in spi_bitbang_init. Because of this, performing any
TX/RX operation will lead to a kernel oops.
Also drop the redundant cleanup assignment, as it's also assigned in
spi_bitbang_init.
Signed-off-by: David Bauer <mail@david-bauer.net>
Link: https://lore.kernel.org/r/20210303160837.165771-2-mail@david-bauer.net
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 19e2132174583beb90c1bd3e9c842bc6d5c944d1 ]
spi-bitbang has to call the chipselect function on the ath79 SPI driver
in order to communicate with the SPI slave device, as the ath79 SPI
driver has three dedicated chipselect lines but can also be used with
GPIOs for the CS lines.
Fixes commit 4a07b8bcd503 ("spi: bitbang: Make chipselect callback optional")
Signed-off-by: David Bauer <mail@david-bauer.net>
Link: https://lore.kernel.org/r/20210303160837.165771-1-mail@david-bauer.net
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Takumi Sueda