[ Upstream commit a946506c48f3bd09363c9d2b0a178e55733bcbb6 ]
The driver was registering IRQ 0 when no IRQ was set. This leads to
warnings with newer kernels.
Clear the resource flags, so no resource is registered at all in this
case.
Fixes: 2f17dd34ff ("mfd: tqmx86: IO controller with I2C, Wachdog and GPIO")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f949a9ebce7a18005266b859a17f10c891bb13d7 ]
On Cherry Trail devices with an AXP288 PMIC the external SD-card slot
used the AXP's DLDO2 as card-voltage and either DLDO3 or GPIO1LDO
(GPIO1 pin in low noise LDO mode) as signal-voltage.
These regulators are turned on/off and in case of the signal-voltage
also have their output-voltage changed by the _PS0 and _PS3 power-
management ACPI methods on the MMC-controllers ACPI fwnode as well as
by the _DSM ACPI method for changing the signal voltage.
The AML code implementing these methods is directly accessing the
PMIC through ACPI I2C OpRegion accesses, instead of using the special
PMIC OpRegion handled by drivers/acpi/pmic/intel_pmic_xpower.c .
This means that the contents of the involved PMIC registers can change
without the change being made through the regmap interface, so regmap
should not cache the contents of these registers.
Mark the regulator power on/off, the regulator voltage control and the
GPIO1 control registers as volatile, to avoid regmap caching them.
Specifically this fixes an issue on some models where the i915 driver
toggles another LDO using the same on/off register on/off through
MIPI sequences (through intel_soc_pmic_exec_mipi_pmic_seq_element())
which then writes back a cached on/off register-value where the
card-voltage is off causing the external sdcard slot to stop working
when the screen goes blank, or comes back on again.
The regulator register-range now marked volatile also includes the
buck regulator control registers. This is done on purpose these are
normally not touched by the AML code, but they are updated directly
by the SoC's PUNIT which means that they may also change without going
through regmap.
Note the AXP288 PMIC is only used on Bay- and Cherry-Trail platforms,
so even though this is an ACPI specific problem there is no need to
make the new volatile ranges conditional since these platforms always
use ACPI.
Fixes: dc91c3b6fe66 ("mfd: axp20x: Mark AXP20X_VBUS_IPSOUT_MGMT as volatile")
Fixes: cd53216625 ("mfd: axp20x: Fix axp288 volatile ranges")
Reported-and-tested-by: Clamshell <clamfly@163.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ff80e2de36d0554e3a6da18a171719fe8663c17 ]
Although irq_create_mapping() is able to deal with duplicate
mappings, it really isn't supposed to be a substitute for
irq_find_mapping(), and can result in allocations that take place
in atomic context if the mapping didn't exist.
Fix the handful of MFD drivers that use irq_create_mapping() in
interrupt context by using irq_find_mapping() instead.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ec343111c056ec3847800302f6dbc57281f833fa ]
These are the actual frequencies reported by the PLL, so let's
report these. The roundoffs are inappropriate, we should round
to the frequency that the clock will later report.
Drop some whitespace at the same time.
Cc: phone-devel@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0b7cbe811ca524295ea43d9a4d73d3427e419c54 ]
We have started to get a bunch of pointless dmamask not set warnings
that makes the output of dmesg -l err,warn hard to read with many
extra warnings:
cpcap-regulator cpcap-regulator.0: DMA mask not set
cpcap_adc cpcap_adc.0: DMA mask not set
cpcap_battery cpcap_battery.0: DMA mask not set
cpcap-charger cpcap-charger.0: DMA mask not set
cpcap-pwrbutton cpcap-pwrbutton.0: DMA mask not set
cpcap-led cpcap-led.0: DMA mask not set
cpcap-led cpcap-led.1: DMA mask not set
cpcap-led cpcap-led.2: DMA mask not set
cpcap-led cpcap-led.3: DMA mask not set
cpcap-led cpcap-led.4: DMA mask not set
cpcap-rtc cpcap-rtc.0: DMA mask not set
cpcap-usb-phy cpcap-usb-phy.0: DMA mask not set
This seems to have started with commit 4d8bde883b ("OF: Don't set
default coherent DMA mask"). We have the parent SPI controller use
DMA, while CPCAP driver and it's children do not. For audio, the
DMA is handled over I2S bus with the McBSP driver.
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Ivan Jelincic <parazyd@dyne.org>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Sicelo A. Mhlongo <absicsz@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4700ef326556ed74aba188f12396740a8c1c21dd ]
This patch adds/modifies MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4917e498c6894ba077867aff78f82cffd5ffbb5c ]
The ARR register is cleared unconditionally upon probing, after the maximum
value has been read. This initial condition is rather not intuitive, when
considering the counter child driver. It rather expects the maximum value
by default:
- The counter interface shows a zero value by default for 'ceiling'
attribute.
- Enabling the counter without any prior configuration makes it doesn't
count.
The reset value of ARR register is the maximum. So Choice here
is to backup it, and restore it then, instead of clearing its value.
It also fixes the initial condition seen by the counter driver.
Fixes: d0f949e220 ("mfd: Add STM32 Timers driver")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fe6df2b48043bbe1e852b2320501d3b169363c35 ]
pm_runtime_get_sync() will increase the rumtime PM counter
even it returns an error. Thus a pairing decrement is needed
to prevent refcount leak. Fix this by replacing this API with
pm_runtime_resume_and_get(), which will not change the runtime
PM counter on error.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 26783d74cc6a440ee3ef9836a008a697981013d0 ]
The "req" struct is always added to the "wm831x->auxadc_pending" list,
but it's only removed from the list on the success path. If a failure
occurs then the "req" struct is freed but it's still on the list,
leading to a use after free.
Fixes: 78bb3688ea ("mfd: Support multiple active WM831x AUXADC conversions")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c58ad0f2b052b5675d6394e03713ee41e721b44c ]
To remove mfd devices when unload this driver, should use
devm_mfd_add_devices() instead.
Fixes: d3ea212720 ("mfd: Add ROHM BD9571MWV-M MFD PMIC driver")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-for-MFD-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
-----BEGIN PGP SIGNATURE-----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=fZ3T
-----END PGP SIGNATURE-----
Merge tag 'v5.4.73' into 5.4-2.3.x-imx
This is the 5.4.73 stable release
Conflicts:
- arch/arm/boot/dts/imx6sl.dtsi:
Commit [a1767c9019] in NXP tree is now covered with commit [5c4c2f437c]
from upstream.
- drivers/gpu/drm/mxsfb/mxsfb_drv.c:
Resolve merge hunk for patch [ed8b90d303] from upstream
- drivers/media/i2c/ov5640.c:
Patch [aa4bb8b883] in NXP tree is now covered by patches [79ec0578c7]
and [b2f8546056] from upstream. Changes from NXP patch [99aa4c8c18] are
covered in upstream version as well.
- drivers/net/ethernet/freescale/fec_main.c:
Fix merge fuzz for patch [9e70485b40] from upstream.
- drivers/usb/cdns3/gadget.c:
Keep NXP version of the file, upstream version is not compatible.
- drivers/usb/dwc3/core.c:
- drivers/usb/dwc3/core.h:
Fix merge fuzz of patch [08045050c6] together wth NXP patch [b30e41dc1e]
- sound/soc/fsl/fsl_sai.c:
- sound/soc/fsl/fsl_sai.h:
Commit [2ea70e51eb72a] in NXP tree is now covered with commit [1ad7f52fe6]
from upstream.
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
commit a75bfc824a2d33f57ebdc003bfe6b7a9e11e9cb9 upstream.
When changing to use suspend-to-idle to save power, the PMIC irq can not
wakeup the system due to lack of wakeup capability, which will cause
the sub-irqs (such as power key) of the PMIC can not wake up the system.
Thus we can add the wakeup capability for PMIC irq to solve this issue,
as well as removing the IRQF_NO_SUSPEND flag to allow PMIC irq to be
a wakeup source.
Reported-by: Chunyan Zhang <zhang.lyra@gmail.com>
Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Tested-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Complete cts value for 32kHz and different pixel clock,
otherwise there is no sound for 32kHz.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Sandor Yu<Sandor.yu@nxp.com>
Fix PTR_ERR build warning from below patch:
commit bb9da18bac ("MA-18186 mfd: pca9450: handle EPROBE_DEFER when get pmic_plat_data")
drivers/mfd/pca9450.c:169:25: warning: passing argument 1
of ‘PTR_ERR’ makes pointer from integer without a cast [-Wint-conversion]
169 | if (PTR_ERR(board_info->gpio_intr) != -EPROBE_DEFER)
Signed-off-by: Jindong Yue <jindong.yue@nxp.com>
Reviewed-by: Robin Gong <yibin.gong@nxp.com>
If pca9450 is probed before the GPIO driver, it may miss the gpio_intr
configuration in dts.
Add defer probe handler to wait GPIO driver probe.
Change-Id: Iafbddcb0ee5144043c4e67f0e361cfe0577940e8
Reviewed-by: Robin Gong <yibin.gong@nxp.com>
Signed-off-by: Jindong Yue <jindong.yue@nxp.com>
[ Upstream commit 8ce24f8967df2836b4557a23e74dc4bb098249f1 ]
This code should clean up if sm501_init_dev() fails.
Fixes: b6d6454fdb ("[PATCH] mfd: SM501 core driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
* tag 'v5.4.70': (3051 commits)
Linux 5.4.70
netfilter: ctnetlink: add a range check for l3/l4 protonum
ep_create_wakeup_source(): dentry name can change under you...
...
Conflicts:
arch/arm/mach-imx/pm-imx6.c
arch/arm64/boot/dts/freescale/imx8mm-evk.dts
arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts
drivers/crypto/caam/caamalg.c
drivers/gpu/drm/imx/dw_hdmi-imx.c
drivers/gpu/drm/imx/imx-ldb.c
drivers/gpu/drm/imx/ipuv3/ipuv3-crtc.c
drivers/mmc/host/sdhci-esdhc-imx.c
drivers/net/ethernet/freescale/dpaa2/dpaa2-eth.c
drivers/net/ethernet/freescale/enetc/enetc.c
drivers/net/ethernet/freescale/enetc/enetc_pf.c
drivers/thermal/imx_thermal.c
drivers/usb/cdns3/ep0.c
drivers/xen/swiotlb-xen.c
sound/soc/fsl/fsl_esai.c
sound/soc/fsl/fsl_sai.c
Signed-off-by: Jason Liu <jason.hui.liu@nxp.com>
[ Upstream commit b195e101580db390f50b0d587b7f66f241d2bc88 ]
If a child device calls mfd_cell_{en,dis}able() without an appropriate
call-back being set, we are likely to encounter a panic. Avoid this
by adding suitable checking.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bb7fcad48d3804d814b97c785514e2d1657e157f ]
Intel Tiger Lake PCH-H has the same LPSS than Intel Broxton.
Add the new IDs to the list of supported devices.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ea2e4eab64cefa06055bb0541fcdedad4b48565 ]
Intel Emmitsburg PCH has the same LPSS than Intel Ice Lake.
Add the new IDs to the list of supported devices.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3d858942250820b9adc35f963a257481d6d4c81d ]
The event handler loop must be run with interrupts disabled.
Otherwise we will have a warning:
[ 1970.785649] irq 31 handler lineevent_irq_handler+0x0/0x20 enabled interrupts
[ 1970.792739] WARNING: CPU: 0 PID: 0 at kernel/irq/handle.c:159 __handle_irq_event_percpu+0x162/0x170
[ 1970.860732] RIP: 0010:__handle_irq_event_percpu+0x162/0x170
...
[ 1970.946994] Call Trace:
[ 1970.949446] <IRQ>
[ 1970.951471] handle_irq_event_percpu+0x2c/0x80
[ 1970.955921] handle_irq_event+0x23/0x43
[ 1970.959766] handle_simple_irq+0x57/0x70
[ 1970.963695] generic_handle_irq+0x42/0x50
[ 1970.967717] dln2_rx+0xc1/0x210 [dln2]
[ 1970.971479] ? usb_hcd_unmap_urb_for_dma+0xa6/0x1c0
[ 1970.976362] __usb_hcd_giveback_urb+0x77/0xe0
[ 1970.980727] usb_giveback_urb_bh+0x8e/0xe0
[ 1970.984837] tasklet_action_common.isra.0+0x4a/0xe0
...
Recently xHCI driver switched to tasklets in the commit 36dc01657b49
("usb: host: xhci: Support running urb giveback in tasklet context").
The handle_irq_event_* functions are expected to be called with interrupts
disabled and they rightfully complain here because we run in tasklet context
with interrupts enabled.
Use a event spinlock to protect event handler from being interrupted.
Note, that there are only two users of this GPIO and ADC drivers and both of
them are using generic_handle_irq() which makes above happen.
Fixes: 338a128142 ("mfd: Add support for Diolan DLN-2 devices")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ddff6c45b21d0437ce0c85f8ac35d7b5480513d7 ]
Whilst it doesn't matter if the internal 32k clock register settings
are cleaned up on exit, as the part will be turned off losing any
settings, hence the driver hasn't historially bothered. The external
clock should however be cleaned up, as it could cause clocks to be
left on, and will at best generate a warning on unbind.
Add clean up on both the probe error path and unbind for the 32k
clock.
Fixes: cdd8da8cc6 ("mfd: arizona: Add gating of external MCLKn clocks")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 97eda5dcc2cde5dcc778bef7a9344db3b6bf8ef5 ]
When STMFX supply is stopped, spurious interrupt can occur. To avoid that,
disable the interrupt in suspend before disabling the regulator and
re-enable it at the end of resume.
Fixes: 06252ade91 ("mfd: Add ST Multi-Function eXpander (STMFX) core driver")
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 60c2c4bcb9202acad4cc26af20b44b6bd7874f7b ]
In case the interrupt signal can't be configured, IRQ domain needs to be
removed.
Fixes: 06252ade91 ("mfd: Add ST Multi-Function eXpander (STMFX) core driver")
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e583649d87ec090444aa5347af0927cd6e8581ae ]
STMFX supply is disabled during suspend. To avoid a too early access to
the STMFX firmware on resume, reset the chip and wait for its firmware to
be loaded.
Fixes: 06252ade91 ("mfd: Add ST Multi-Function eXpander (STMFX) core driver")
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d4f9b5428b53dd67f49ee8deed8d4366ed6b1933 ]
WM8994 chip has built-in regulators, which might be used for chip
operation. They are controlled by a separate wm8994-regulator driver,
which should be loaded before this driver calls regulator_get(), because
that driver also provides consumer-supply mapping for the them. If that
driver is not yet loaded, regulator core substitute them with dummy
regulator, what breaks chip operation, because the built-in regulators are
never enabled. Fix this by annotating this driver with MODULE_SOFTDEP()
"pre" dependency to "wm8994_regulator" module.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit a8ff78f7f773142eb8a8befe5a95dd6858ebd635 upstream.
Some BIOS erroneously specifies write-combining BAR for intel-lpss-pci
in MTRR. This will cause the system to hang during boot. If possible,
this bug could be corrected with a firmware update.
This patch use devm_ioremap_uc to overwrite/ignore the MTRR settings
by forcing the use of strongly uncachable pages for intel-lpss.
The BIOS bug is present on Dell XPS 13 7390 2-in-1:
[ 0.001734] 5 base 4000000000 mask 6000000000 write-combining
4000000000-7fffffffff : PCI Bus 0000:00
4000000000-400fffffff : 0000:00:02.0 (i915)
4010000000-4010000fff : 0000:00:15.0 (intel-lpss-pci)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=203485
Cc: <stable@vger.kernel.org> # v4.19+
Tested-by: AceLan Kao <acelan.kao@canonical.com>
Signed-off-by: Tuowen Zhao <ztuowen@gmail.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Roman Gilg <subdiff@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fb945c95a482200876993977008b67ea658bd938 ]
While the commit 2b8bd606b1e6 ("mfd: dln2: More sanity checking for endpoints")
tries to harden the sanity checks it made at the same time a regression,
i.e. mixed in and out endpoints. Obviously it should have been not tested on
real hardware at that time, but unluckily it didn't happen.
So, fix above mentioned typo and make device being enumerated again.
While here, introduce an enumerator for magic values to prevent similar issue
to happen in the future.
Fixes: 2b8bd606b1e6 ("mfd: dln2: More sanity checking for endpoints")
Cc: Oliver Neukum <oneukum@suse.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit cb7a374a5e7a5af3f8c839f74439193add6d0589 upstream.
MAX77650 MFD driver uses regmap_irq API but doesn't select the required
REGMAP_IRQ option in Kconfig. This can cause the following build error
if regmap irq is not enabled implicitly by someone else:
ld: drivers/mfd/max77650.o: in function `max77650_i2c_probe':
max77650.c:(.text+0xcb): undefined reference to `devm_regmap_add_irq_chip'
ld: max77650.c:(.text+0xdb): undefined reference to `regmap_irq_get_domain'
make: *** [Makefile:1079: vmlinux] Error 1
Fix it by adding the missing option.
Fixes: d0f6033450 ("mfd: Add new driver for MAX77650 PMIC")
Reported-by: Paul Gazzillo <paul@pgazz.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2f3dc25c0118de03a00ddc88b61f7216854f534d upstream.
There is a bit which gets cleared after conversion.
Fixes: 9bb9e29c78 ("mfd: Add Ricoh RN5T618 PMIC core driver")
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1112ba02ff1190ca9c15a912f9269e54b46d2d82 upstream.
The watchdog driver compatible is "dlg,da9062-watchdog" and not
"dlg,da9062-wdt". Therefore the mfd-core can't populate the of_node and
fwnode. As result the watchdog driver can't parse the devicetree.
Fixes: 9b40b030c4 ("mfd: da9062: Supply core driver")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dc91c3b6fe66a13ac76f6cb3b2100c0779cd3350 upstream.
On AXP288 and newer PMICs, bit 7 of AXP20X_VBUS_IPSOUT_MGMT can be set
to prevent using the VBUS input. However, when the VBUS unplugged and
plugged back in, the bit automatically resets to zero.
We need to set the register as volatile to prevent regmap from caching
that bit. Otherwise, regcache will think the bit is already set and not
write the register.
Fixes: cd53216625 ("mfd: axp20x: Fix axp288 volatile ranges")
Cc: stable@vger.kernel.org
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2b8bd606b1e60ca28c765f69c1eedd7d2a2e9dca upstream.
It is not enough to check for the number of endpoints.
The types must also be correct.
Reported-and-tested-by: syzbot+48a2851be24583b864dc@syzkaller.appspotmail.com
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit dd047dce3a6f5233b98e792e2287cc549da35879 ]
Intel Comet Lake PCH-H has the same LPSS than Intel Cannon Lake.
Add the new IDs to the list of supported devices.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 3f31bc67e4dc6a555341dffefe328ddd58e8b431 upstream.
It turned out Intel Gemini Lake doesn't use the same I2C timing
parameters as Broxton.
I got confirmation from the Windows team that Gemini Lake systems should
use updated timing parameters that differ from those used in Broxton
based systems.
Fixes: f80e78aa11 ("mfd: intel-lpss: Add Intel Gemini Lake PCI IDs")
Tested-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some of the i.MX SoCs have a IP for interfacing the audio dedicated IPs with
clocks, resets and interrupts, plus some DSP specific control registers.
To allow the functionality to be split between drivers, this MFD driver is
added that has only two purposes: register the devices and map the entire
register addresses. Everything else is left to the dedicated drivers that will
bind to the registered devices.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Add new pmic pca9450 driver for i.mx8mn-evk board.
Signed-off-by: John Lee <john.lee@nxp.com>
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Reviewed-by: Anson Huang <anson.huang@nxp.com>
(cherry picked from commit 2189979539)
There is issue that system can't enter suspend while the si476x is
working.
The reason is that with the workqueue thread is still working after
i2c enter suspend, then cause the cpu_suspend function failed.
This patch is to use the system_freezable_wq instead of the system_wq,
that the workqueue will be freeze before system enter suspend.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Viorel Suman <viorel.suman@nxp.com>
Andrey Zhizhikin