[ Upstream commit 4108b3e6db31acc4c68133290bbcc87d4db905c9 ]
These for-loops should test against v4l2_dv_timings_presets[i].bt.width,
not if i < v4l2_dv_timings_presets[i].bt.width. Luckily nothing ever broke,
since the smallest width is still a lot higher than the total number of
presets, but it is wrong.
The last item in the presets array is all 0, so the for-loop must stop
when it reaches that sentinel.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f809665ee75fff3f4ea8907f406a66d380aeb184 ]
The range for analog gain mentioned in the datasheet is [0, 480].
The real gain formula mentioned in the datasheet is:
Gain = 512 / (512 – X)
Hence, values larger than 511 clearly makes no sense. The gain
register field is also documented to be of 9-bits in the datasheet.
Certainly, it is enough to infer that, the kernel driver currently
advertises an arbitrary analog gain max. Fix it by rectifying the
value as per the data sheet i.e. 480.
Signed-off-by: Umang Jain <umang.jain@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 51f93add3669f1b1f540de1cf397815afbd4c756 ]
The frame_length_lines (0x0340) registers are hard-coded as follows:
- 4208x3118
frame_length_lines = 0x0c50
- 2104x1560
frame_length_lines = 0x0638
- 1048x780
frame_length_lines = 0x034c
The driver exposes the V4L2_CID_VBLANK control in read-only mode and
sets its value to vts_def - height, where vts_def is a mode-dependent
value coming from the supported_modes array. It is set using one of
the following macros defined in the driver:
#define IMX258_VTS_30FPS 0x0c98
#define IMX258_VTS_30FPS_2K 0x0638
#define IMX258_VTS_30FPS_VGA 0x034c
There's a clear mismatch in the value for the full resolution mode i.e.
IMX258_VTS_30FPS. Fix it by rectifying the macro with the value set for
the frame_length_lines register as stated above.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Umang Jain <umang.jain@ideasonboard.com>
Reviewed-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8db11aebdb8f93f46a8513c22c9bd52fa23263aa ]
The logic at dib8000_get_init_prbs() has a few issues:
1. the tables used there has an extra unused value at the beginning;
2. the dprintk() message doesn't write the right value when
transmission mode is not 8K;
3. the array overflow validation is done by the callers.
Rewrite the code to fix such issues.
This should also shut up those smatch warnings:
drivers/media/dvb-frontends/dib8000.c:2125 dib8000_get_init_prbs() error: buffer overflow 'lut_prbs_8k' 14 <= 14
drivers/media/dvb-frontends/dib8000.c:2129 dib8000_get_init_prbs() error: buffer overflow 'lut_prbs_2k' 14 <= 14
drivers/media/dvb-frontends/dib8000.c:2131 dib8000_get_init_prbs() error: buffer overflow 'lut_prbs_4k' 14 <= 14
drivers/media/dvb-frontends/dib8000.c:2134 dib8000_get_init_prbs() error: buffer overflow 'lut_prbs_8k' 14 <= 14
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 6b7f554be8c92319d7e6df92fd247ebb9beb4a45 upstream.
The LIRC_SET_TRANSMITTER_MASK ioctl should return the number of emitters
if an invalid list was set.
Cc: stable@vger.kernel.org
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1a10d7fdb6d0e235e9d230916244cc2769d3f170 upstream.
As warned by smatch:
drivers/media/usb/uvc/uvc_v4l2.c:911 uvc_ioctl_g_input() error: doing dma on the stack (&i)
drivers/media/usb/uvc/uvc_v4l2.c:943 uvc_ioctl_s_input() error: doing dma on the stack (&i)
those two functions call uvc_query_ctrl passing a pointer to
a data at the DMA stack. those are used to send URBs via
usb_control_msg(). Using DMA stack is not supported and should
not work anymore on modern Linux versions.
So, use a kmalloc'ed buffer.
Cc: stable@vger.kernel.org # Kernel 4.9 and upper
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 09ea9719a423fc675d40dd05407165e161ea0c48 ]
Currently the call to find_format can potentially return a NULL to
fmt and the nullpointer is later dereferenced on the assignment of
pixmp->num_planes = fmt->num_planes. Fix this by adding a NULL pointer
check and returning NULL for the failure case.
Addresses-Coverity: ("Dereference null return")
Fixes: aaaa93eda6 ("[media] media: venus: venc: add video encoder files")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6fa54bc713c262e1cfbc5613377ef52280d7311f ]
If em28xx_ir_init fails, it would decrease the refcount of dev. However,
in the em28xx_ir_fini, when ir is NULL, it goes to ref_put and decrease
the refcount of dev. This will lead to a refcount bug.
Fix this bug by removing the kref_put in the error handling code
of em28xx_ir_init.
refcount_t: underflow; use-after-free.
WARNING: CPU: 0 PID: 7 at lib/refcount.c:28 refcount_warn_saturate+0x18e/0x1a0 lib/refcount.c:28
Modules linked in:
CPU: 0 PID: 7 Comm: kworker/0:1 Not tainted 5.13.0 #3
Workqueue: usb_hub_wq hub_event
RIP: 0010:refcount_warn_saturate+0x18e/0x1a0 lib/refcount.c:28
Call Trace:
kref_put.constprop.0+0x60/0x85 include/linux/kref.h:69
em28xx_usb_disconnect.cold+0xd7/0xdc drivers/media/usb/em28xx/em28xx-cards.c:4150
usb_unbind_interface+0xbf/0x3a0 drivers/usb/core/driver.c:458
__device_release_driver drivers/base/dd.c:1201 [inline]
device_release_driver_internal+0x22a/0x230 drivers/base/dd.c:1232
bus_remove_device+0x108/0x160 drivers/base/bus.c:529
device_del+0x1fe/0x510 drivers/base/core.c:3540
usb_disable_device+0xd1/0x1d0 drivers/usb/core/message.c:1419
usb_disconnect+0x109/0x330 drivers/usb/core/hub.c:2221
hub_port_connect drivers/usb/core/hub.c:5151 [inline]
hub_port_connect_change drivers/usb/core/hub.c:5440 [inline]
port_event drivers/usb/core/hub.c:5586 [inline]
hub_event+0xf81/0x1d40 drivers/usb/core/hub.c:5668
process_one_work+0x2c9/0x610 kernel/workqueue.c:2276
process_scheduled_works kernel/workqueue.c:2338 [inline]
worker_thread+0x333/0x5b0 kernel/workqueue.c:2424
kthread+0x188/0x1d0 kernel/kthread.c:319
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:295
Reported-by: Dongliang Mu <mudongliangabcd@gmail.com>
Fixes: ac5688637144 ("media: em28xx: Fix possible memory leak of em28xx struct")
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 44693d74f5653f82cd7ca0fe730eed0f6b83306a ]
The frame memory control register value is currently determined
before userspace selects the final capture format and never corrected.
Update ctx->frame_mem_ctrl in __coda_start_decoding() to fix decoding
into YUV420 or YVU420 capture buffers.
Reported-by: Andrej Picej <andrej.picej@norik.com>
Fixes: 497e6b8559 ("media: coda: add sequence initialization work")
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6f5885a7750545973bf1a942d2f0f129aef0aa06 ]
In go7007_alloc() kzalloc() is used for struct go7007
allocation. It means that there is no need in zeroing
any members, because kzalloc will take care of it.
Removing these reduntant initialization steps increases
execution speed a lot:
Before:
+ 86.802 us | go7007_alloc();
After:
+ 29.595 us | go7007_alloc();
Fixes: 866b8695d6 ("Staging: add the go7007 video driver")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 131ae388b88e3daf4cb0721ed4b4cb8bfc201465 ]
In dvb_usb_i2c_init, if i2c_add_adapter fails, it only prints an error
message, and then continues to set DVB_USB_STATE_I2C. This affects the
logic of dvb_usb_i2c_exit, which leads to that, the deletion of i2c_adap
even if the i2c_add_adapter fails.
Fix this by returning at the failure of i2c_add_adapter and then move
dvb_usb_i2c_exit out of the error handling code of dvb_usb_i2c_init.
Fixes: 13a79f14ab28 ("media: dvb-usb: Fix memory leak at error in dvb_usb_device_init()")
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 797c061ad715a9a1480eb73f44b6939fbe3209ed ]
If vp702x_usb_in_op fails, the mac address is not initialized.
And vp702x_read_mac_addr does not handle this failure, which leads to
the uninit-value in dvb_usb_adapter_dvb_init.
Fix this by handling the failure of vp702x_usb_in_op.
Fixes: 786baecfe7 ("[media] dvb-usb: move it to drivers/media/usb/dvb-usb")
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c5453769f77ce19a5b03f1f49946fd3f8a374009 ]
If dibusb_read_eeprom_byte fails, the mac address is not initialized.
And nova_t_read_mac_address does not handle this failure, which leads to
the uninit-value in dvb_usb_adapter_dvb_init.
Fix this by handling the failure of dibusb_read_eeprom_byte.
Reported-by: syzbot+e27b4fd589762b0b9329@syzkaller.appspotmail.com
Fixes: 786baecfe7 ("[media] dvb-usb: move it to drivers/media/usb/dvb-usb")
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dcb0145821017e929a733e2271c85c6f82b9c9f8 ]
If an error occurs after a successful 'regulator_enable()' call,
'regulator_disable()' must be called.
Fix the error handling path of the probe accordingly.
Fixes: cb496cd472 ("media: cxd2880-spi: Add optional vcc regulator")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ea3e1c36e38810427485f06c2becc1f29e54521d ]
Without this patch, the TDA19971 chip's EDID is inactive.
EDID never worked with this driver, it was all tested with HDMI signal
sources which don't need EDID support.
Signed-off-by: Krzysztof Halasa <khalasa@piap.pl>
Fixes: 9ac0038db9 ("media: i2c: Add TDA1997x HDMI receiver driver")
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 514e97674400462cc09c459a1ddfb9bf39017223 upstream.
My local syzbot instance hit memory leak in usb_set_configuration().
The problem was in unputted usb interface. In case of errors after
usb_get_intf() the reference should be putted to correclty free memory
allocated for this interface.
Fixes: ec16dae545 ("V4L/DVB (7019): V4L: add support for Syntek DC1125 webcams")
Cc: stable@vger.kernel.org
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9c39be40c0155c43343f53e3a439290c0fec5542 ]
syzbot reported memory leak in zr364xx_probe()[1].
The problem was in invalid error handling order.
All error conditions rigth after v4l2_ctrl_handler_init()
must call v4l2_ctrl_handler_free().
Reported-by: syzbot+efe9aefc31ae1e6f7675@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ea354b6ddd6f09be29424f41fa75a3e637fea234 ]
Syzbot discovered that the probe error handling doesn't clean up the
resources allocated in zr364xx_board_init(). There are several
related bugs in this code so I have re-written the error handling.
1) Introduce a new function zr364xx_board_uninit() which cleans up
the resources in zr364xx_board_init().
2) In zr364xx_board_init() if the call to zr364xx_start_readpipe()
fails then release the "cam->buffer.frame[i].lpvbits" memory
before returning. This way every function either allocates
everything successfully or it cleans up after itself.
3) Re-write the probe function so that each failure path goto frees
the most recent allocation. That way we don't free anything
before it has been allocated and we can also verify that
everything is freed.
4) Originally, in the probe function the "cam->v4l2_dev.release"
pointer was set to "zr364xx_release" near the start but I moved
that assignment to the end, after everything had succeeded. The
release function was never actually called during the probe cleanup
process, but with this change I wanted to make it clear that we
don't want to call zr364xx_release() until everything is
allocated successfully.
Next I re-wrote the zr364xx_release() function. Ideally this would
have been a simple matter of copy and pasting the cleanup code from
probe and adding an additional call to video_unregister_device(). But
there are a couple quirks to note.
1) The probe function does not call videobuf_mmap_free() and I don't
know where the videobuf_mmap is allocated. I left the code as-is to
avoid introducing a bug in code I don't understand.
2) The zr364xx_board_uninit() has a call to zr364xx_stop_readpipe()
which is a change from the original behavior with regards to
unloading the driver. Calling zr364xx_stop_readpipe() on a stopped
pipe is not a problem so this is safe and is potentially a bugfix.
Reported-by: syzbot+b4d54814b339b5c6bbd4@syzkaller.appspotmail.com
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit af0321a5be3e5647441eb6b79355beaa592df97a ]
zr364xx_start_readpipe() can fail but callers do not care about that.
This can result in various negative consequences. The patch adds missed
error handling.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 566463afdbc43c7744c5a1b89250fc808df03833 upstream.
If poll() is called on a m2m device with the EPOLLOUT event after the
last buffer of the CAPTURE queue is dequeued, any buffer available on
OUTPUT queue will never be signaled because v4l2_m2m_poll_for_data()
starts by checking whether dst_q->last_buffer_dequeued is set and
returns EPOLLIN in this case, without looking at the state of the OUTPUT
queue.
Fix this by not early returning so we keep checking the state of the
OUTPUT queue afterwards.
Signed-off-by: Alexandre Courbot <gnurou@gmail.com>
Reviewed-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Cc: Lecopzer Chen <lecopzer.chen@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 76f22c93b209c811bd489950f17f8839adb31901 upstream.
The direction of the pipe argument must match the request-type direction
bit or control requests may fail depending on the host-controller-driver
implementation.
Control transfers without a data stage are treated as OUT requests by
the USB stack and should be using usb_sndctrlpipe(). Failing to do so
will now trigger a warning.
The driver uses a zero-length i2c-read request for type detection so
update the control-request code to use usb_sndctrlpipe() in this case.
Note that actually trying to read the i2c register in question does not
work as the register might not exist (e.g. depending on the demodulator)
as reported by Eero Lehtinen <debiangamer2@gmail.com>.
Reported-by: syzbot+faf11bbadc5a372564da@syzkaller.appspotmail.com
Reported-by: Eero Lehtinen <debiangamer2@gmail.com>
Tested-by: Eero Lehtinen <debiangamer2@gmail.com>
Fixes: d0f232e823 ("[media] rtl28xxu: add heuristic to detect chip type")
Cc: stable@vger.kernel.org # 4.0
Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c592b46907adbeb81243f7eb7a468c36692658b8 ]
If a vb2_queue sets q->min_buffers_needed then when the number of
queued buffers reaches q->min_buffers_needed, vb2_core_qbuf() will call
the start_streaming() callback. If start_streaming() returns an error,
then that error was just returned by vb2_core_qbuf(), but the buffer
was still queued. However, userspace expects that if VIDIOC_QBUF fails,
the buffer is returned dequeued.
So if start_streaming() fails, then remove the buffer from the queue,
thus avoiding this unwanted side-effect.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Fixes: b3379c6201 ("[media] vb2: only call start_streaming if sufficient buffers are queued")
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 8d4abca95ecc82fc8c41912fa0085281f19cc29f upstream.
Fix an 11-year old bug in ngene_command_config_free_buf() while
addressing the following warnings caught with -Warray-bounds:
arch/alpha/include/asm/string.h:22:16: warning: '__builtin_memcpy' offset [12, 16] from the object at 'com' is out of the bounds of referenced subobject 'config' with type 'unsigned char' at offset 10 [-Warray-bounds]
arch/x86/include/asm/string_32.h:182:25: warning: '__builtin_memcpy' offset [12, 16] from the object at 'com' is out of the bounds of referenced subobject 'config' with type 'unsigned char' at offset 10 [-Warray-bounds]
The problem is that the original code is trying to copy 6 bytes of
data into a one-byte size member _config_ of the wrong structue
FW_CONFIGURE_BUFFERS, in a single call to memcpy(). This causes a
legitimate compiler warning because memcpy() overruns the length
of &com.cmd.ConfigureBuffers.config. It seems that the right
structure is FW_CONFIGURE_FREE_BUFFERS, instead, because it contains
6 more members apart from the header _hdr_. Also, the name of
the function ngene_command_config_free_buf() suggests that the actual
intention is to ConfigureFreeBuffers, instead of ConfigureBuffers
(which takes place in the function ngene_command_config_buf(), above).
Fix this by enclosing those 6 members of struct FW_CONFIGURE_FREE_BUFFERS
into new struct config, and use &com.cmd.ConfigureFreeBuffers.config as
the destination address, instead of &com.cmd.ConfigureBuffers.config,
when calling memcpy().
This also helps with the ongoing efforts to globally enable
-Warray-bounds and get us closer to being able to tighten the
FORTIFY_SOURCE routines on memcpy().
Link: https://github.com/KSPP/linux/issues/109
Fixes: dae52d009f ("V4L/DVB: ngene: Initial check-in")
Cc: stable@vger.kernel.org
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/linux-hardening/20210420001631.GA45456@embeddedor/
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4c6e0976295add7f0ed94d276c04a3d6f1ea8f83 upstream.
The Elgato Cam Link 4K HDMI video capture card reports to support three
different pixel formats, where the first format depends on the connected
HDMI device.
```
$ v4l2-ctl -d /dev/video0 --list-formats-ext
ioctl: VIDIOC_ENUM_FMT
Type: Video Capture
[0]: 'NV12' (Y/CbCr 4:2:0)
Size: Discrete 3840x2160
Interval: Discrete 0.033s (29.970 fps)
[1]: 'NV12' (Y/CbCr 4:2:0)
Size: Discrete 3840x2160
Interval: Discrete 0.033s (29.970 fps)
[2]: 'YU12' (Planar YUV 4:2:0)
Size: Discrete 3840x2160
Interval: Discrete 0.033s (29.970 fps)
```
Changing the pixel format to anything besides the first pixel format
does not work:
```
$ v4l2-ctl -d /dev/video0 --try-fmt-video pixelformat=YU12
Format Video Capture:
Width/Height : 3840/2160
Pixel Format : 'NV12' (Y/CbCr 4:2:0)
Field : None
Bytes per Line : 3840
Size Image : 12441600
Colorspace : sRGB
Transfer Function : Rec. 709
YCbCr/HSV Encoding: Rec. 709
Quantization : Default (maps to Limited Range)
Flags :
```
User space applications like VLC might show an error message on the
terminal in that case:
```
libv4l2: error set_fmt gave us a different result than try_fmt!
```
Depending on the error handling of the user space applications, they
might display a distorted video, because they use the wrong pixel format
for decoding the stream.
The Elgato Cam Link 4K responds to the USB video probe
VS_PROBE_CONTROL/VS_COMMIT_CONTROL with a malformed data structure: The
second byte contains bFormatIndex (instead of being the second byte of
bmHint). The first byte is always zero. The third byte is always 1.
The firmware bug was reported to Elgato on 2020-12-01 and it was
forwarded by the support team to the developers as feature request.
There is no firmware update available since then. The latest firmware
for Elgato Cam Link 4K as of 2021-03-23 has MCU 20.02.19 and FPGA 67.
Therefore correct the malformed data structure for this device. The
change was successfully tested with VLC, OBS, and Chromium using
different pixel formats (YUYV, NV12, YU12), resolutions (3840x2160,
1920x1080), and frame rates (29.970 and 59.940 fps).
Cc: stable@vger.kernel.org
Signed-off-by: Benjamin Drung <bdrung@posteo.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b4bb4d425b7b02424afea2dfdcd77b3b4794175e upstream.
The direction of the pipe argument must match the request-type direction
bit or control requests may fail depending on the host-controller-driver
implementation.
Control transfers without a data stage are treated as OUT requests by
the USB stack and should be using usb_sndctrlpipe(). Failing to do so
will now trigger a warning.
Fix the single zero-length control request which was using the
read-register helper, and update the helper so that zero-length reads
fail with an error message instead.
Fixes: 6a7eba24e4 ("V4L/DVB (8157): gspca: all subdrivers")
Cc: stable@vger.kernel.org # 2.6.27
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 53ae298fde7adcc4b1432bce2dbdf8dac54dfa72 upstream.
The direction of the pipe argument must match the request-type direction
bit or control requests may fail depending on the host-controller-driver
implementation.
Fix the USB_REQ_SYNCH_FRAME request which erroneously used
usb_sndctrlpipe().
Fixes: 27d35fc3fb ("V4L/DVB (10639): gspca - sq905: New subdriver.")
Cc: stable@vger.kernel.org # 2.6.30
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8c8b9a9be2afa8bd6a72ad1130532baab9fab89d upstream.
The direction of the pipe argument must match the request-type direction
bit or control requests may fail depending on the host-controller-driver
implementation.
Fix the control requests which erroneously used usb_rcvctrlpipe().
Fixes: 8466028be7 ("V4L/DVB (8734): Initial support for AME DTV-5100 USB2.0 DVB-T")
Cc: stable@vger.kernel.org # 2.6.28
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0a7790be182d32b9b332a37cb4206e24fe94b728 upstream.
The saa6588_ioctl() function expects to get called from other kernel
functions with a 'saa6588_command' pointer, but I found nothing stops it
from getting called from user space instead, which seems rather dangerous.
The same thing happens in the davinci vpbe driver with its VENC_GET_FLD
command.
As a quick fix, add a separate .command() callback pointer for this
driver and change the two callers over to that. This change can easily
get backported to stable kernels if necessary, but since there are only
two drivers, we may want to eventually replace this with a set of more
specialized callbacks in the long run.
Fixes: c3fda7f835 ("V4L/DVB (10537): saa6588: convert to v4l2_subdev.")
Cc: stable@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 647d446d66e493d23ca1047fa8492b0269674530 ]
The syscall bpf(BPF_PROG_QUERY, &attr) should use the prog_cnt field to
see how many entries user space provided and return ENOSPC if there are
more programs than that. Before this patch, this is not checked and
ENOSPC is never returned.
Note that one lirc device is limited to 64 bpf programs, and user space
I'm aware of -- ir-keytable -- always gives enough space for 64 entries
already. However, we should not copy program ids than are requested.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20210623213754.632-1-sean@mess.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5d11e6aad1811ea293ee2996cec9124f7fccb661 ]
The m2m_ctx resources was allocated by v4l2_m2m_ctx_init() in g2d_open()
should be freed from g2d_release() when it's not used.
Fix it
Fixes: 918847341a ("[media] v4l: add G2D driver for s5p device family")
Signed-off-by: Dillon Min <dillon.minfei@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 13dfead49db07225335d4f587a560a2210391a1a ]
Rename struct sms_msg_data4 to sms_msg_data5 and increase the size of
its msg_data array from 4 to 5 elements. Notice that at some point
the 5th element of msg_data is being accessed in function
smscore_load_firmware_family2():
1006 trigger_msg->msg_data[4] = 4; /* Task ID */
Also, there is no need for the object _trigger_msg_ of type struct
sms_msg_data *, when _msg_ can be used, directly. Notice that msg_data
in struct sms_msg_data is a one-element array, which causes multiple
out-of-bounds warnings when accessing beyond its first element
in function smscore_load_firmware_family2():
992 struct sms_msg_data *trigger_msg =
993 (struct sms_msg_data *) msg;
994
995 pr_debug("sending MSG_SMS_SWDOWNLOAD_TRIGGER_REQ\n");
996 SMS_INIT_MSG(&msg->x_msg_header,
997 MSG_SMS_SWDOWNLOAD_TRIGGER_REQ,
998 sizeof(struct sms_msg_hdr) +
999 sizeof(u32) * 5);
1000
1001 trigger_msg->msg_data[0] = firmware->start_address;
1002 /* Entry point */
1003 trigger_msg->msg_data[1] = 6; /* Priority */
1004 trigger_msg->msg_data[2] = 0x200; /* Stack size */
1005 trigger_msg->msg_data[3] = 0; /* Parameter */
1006 trigger_msg->msg_data[4] = 4; /* Task ID */
even when enough dynamic memory is allocated for _msg_:
929 /* PAGE_SIZE buffer shall be enough and dma aligned */
930 msg = kmalloc(PAGE_SIZE, GFP_KERNEL | coredev->gfp_buf_flags);
but as _msg_ is casted to (struct sms_msg_data *):
992 struct sms_msg_data *trigger_msg =
993 (struct sms_msg_data *) msg;
the out-of-bounds warnings are actually valid and should be addressed.
Fix this by declaring object _msg_ of type struct sms_msg_data5 *,
which contains a 5-elements array, instead of just 4. And use
_msg_ directly, instead of creating object trigger_msg.
This helps with the ongoing efforts to enable -Warray-bounds by fixing
the following warnings:
CC [M] drivers/media/common/siano/smscoreapi.o
drivers/media/common/siano/smscoreapi.c: In function ‘smscore_load_firmware_family2’:
drivers/media/common/siano/smscoreapi.c:1003:24: warning: array subscript 1 is above array bounds of ‘u32[1]’ {aka ‘unsigned int[1]’} [-Warray-bounds]
1003 | trigger_msg->msg_data[1] = 6; /* Priority */
| ~~~~~~~~~~~~~~~~~~~~~^~~
In file included from drivers/media/common/siano/smscoreapi.c:12:
drivers/media/common/siano/smscoreapi.h:619:6: note: while referencing ‘msg_data’
619 | u32 msg_data[1];
| ^~~~~~~~
drivers/media/common/siano/smscoreapi.c:1004:24: warning: array subscript 2 is above array bounds of ‘u32[1]’ {aka ‘unsigned int[1]’} [-Warray-bounds]
1004 | trigger_msg->msg_data[2] = 0x200; /* Stack size */
| ~~~~~~~~~~~~~~~~~~~~~^~~
In file included from drivers/media/common/siano/smscoreapi.c:12:
drivers/media/common/siano/smscoreapi.h:619:6: note: while referencing ‘msg_data’
619 | u32 msg_data[1];
| ^~~~~~~~
drivers/media/common/siano/smscoreapi.c:1005:24: warning: array subscript 3 is above array bounds of ‘u32[1]’ {aka ‘unsigned int[1]’} [-Warray-bounds]
1005 | trigger_msg->msg_data[3] = 0; /* Parameter */
| ~~~~~~~~~~~~~~~~~~~~~^~~
In file included from drivers/media/common/siano/smscoreapi.c:12:
drivers/media/common/siano/smscoreapi.h:619:6: note: while referencing ‘msg_data’
619 | u32 msg_data[1];
| ^~~~~~~~
drivers/media/common/siano/smscoreapi.c:1006:24: warning: array subscript 4 is above array bounds of ‘u32[1]’ {aka ‘unsigned int[1]’} [-Warray-bounds]
1006 | trigger_msg->msg_data[4] = 4; /* Task ID */
| ~~~~~~~~~~~~~~~~~~~~~^~~
In file included from drivers/media/common/siano/smscoreapi.c:12:
drivers/media/common/siano/smscoreapi.h:619:6: note: while referencing ‘msg_data’
619 | u32 msg_data[1];
| ^~~~~~~~
Fixes: 018b0c6f8a ("[media] siano: make load firmware logic to work with newer firmwares")
Co-developed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8ed339f23d41e21660a389adf2e7b2966d457ff6 ]
The direction of the pipe argument must match the request-type direction
bit or control requests may fail depending on the host-controller-driver
implementation.
Control transfers without a data stage are treated as OUT requests by
the USB stack and should be using usb_sndctrlpipe(). Failing to do so
will now trigger a warning.
Fix the gl860_RTx() helper so that zero-length control reads fail with
an error message instead. Note that there are no current callers that
would trigger this.
Fixes: 4f7cb8837c ("V4L/DVB (12954): gspca - gl860: Addition of GL860 based webcams")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a6b1e7093f0a099571fc8836ab4a589633f956a8 ]
When the CSI bps per lane is not in the valid range, an appropriate error
code -EINVAL should be returned. However, we currently do not explicitly
assign this error code to 'ret'. As a result, 0 was incorrectly returned.
Fixes: 2561482468 ("[media] tc358743: support probe from device tree")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8f2e452730d2bcd59fe05246f0e19a4c52e0012d ]
The media_device_usb_allocate() function returns error pointers when
it's enabled and something goes wrong. It can return NULL as well, but
only if CONFIG_MEDIA_CONTROLLER is disabled so that doesn't apply here.
Fixes: 812658d88d ("media: change au0828 to use Media Device Allocator API")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 01fe904c9afd26e79c1f73aa0ca2e3d785e5e319 ]
In isp_video_release, file->private_data is freed via
_vb2_fop_release()->v4l2_fh_release(). But the freed
file->private_data is still used in v4l2_fh_is_singular_file()
->v4l2_fh_is_singular(file->private_data), which is a use
after free bug.
My patch uses a variable 'is_singular_file' to avoid the uaf.
v3: https://lore.kernel.org/patchwork/patch/1419058/
Fixes: 34947b8aeb ("[media] exynos4-is: Add the FIMC-IS ISP capture DMA driver")
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9c87ae1a0dbeb5794957421157fd266d38a869b4 ]
'ret' is known to be 1 here. In fact 'i' is expected instead.
Store the return value of 'i2c_master_recv()' in 'ret' so that the error
message print the correct error code.
Fixes: acaa34bf06 ("media: rc: implement zilog transmitter")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8edcb5049ac29aa3c8acc5ef15dd4036543d747e ]
The use of an enum named 'RST' conflicts with a #define macro
named 'RST' in arch/mips/include/asm/mach-rc32434/rb.h.
The MIPS use of RST was there first (AFAICT), so change the
media/i2c/ uses of RST to be named 'RSET'.
'git grep -w RSET' does not report any naming conflicts with the
new name.
This fixes multiple build errors:
arch/mips/include/asm/mach-rc32434/rb.h:15:14: error: expected identifier before '(' token
15 | #define RST (1 << 15)
| ^
drivers/media/i2c/s5c73m3/s5c73m3.h:356:2: note: in expansion of macro 'RST'
356 | RST,
| ^~~
../arch/mips/include/asm/mach-rc32434/rb.h:15:14: error: expected identifier before '(' token
15 | #define RST (1 << 15)
| ^
../drivers/media/i2c/s5k6aa.c:180:2: note: in expansion of macro 'RST'
180 | RST,
| ^~~
../arch/mips/include/asm/mach-rc32434/rb.h:15:14: error: expected identifier before '(' token
15 | #define RST (1 << 15)
| ^
../drivers/media/i2c/s5k5baf.c:238:2: note: in expansion of macro 'RST'
238 | RST,
| ^~~
and some others that I have trimmed.
Fixes: cac47f1822 ("[media] V4L: Add S5C73M3 camera driver")
Fixes: 8b99312b72 ("[media] Add v4l2 subdev driver for S5K4ECGX sensor")
Fixes: 7d459937dc ("[media] Add driver for Samsung S5K5BAF camera sensor")
Fixes: bfa8dd3a05 ("[media] v4l: Add v4l2 subdev driver for S5K6AAFX sensor")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Sangwook Lee <sangwook.lee@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 747bad54a677d8633ec14b39dfbeb859c821d7f2 ]
There's a bug at s5p_cec_adap_enable(): if called to
disable the device, it should call pm_runtime_put()
instead of pm_runtime_disable(), as the goal here is to
decrement the usage_count and not to disable PM runtime.
Reported-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fixes: 1bcbf6f4b6 ("[media] cec: s5p-cec: Add s5p-cec driver")
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Andrey Zhizhikin