[ Upstream commit c7bcbc8ab9cb20536b8f50c62a48cebda965fdba ]
Geert reported that his SH7722-based Migo-R board failed to boot after
commit:
c5b27a889d ("sh/tlb: Convert SH to generic mmu_gather")
That commit fell victim to copying the wrong pattern --
__pmd_free_tlb() used to be implemented with pmd_free().
Fixes: c5b27a889d ("sh/tlb: Convert SH to generic mmu_gather")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rich Felker <dalias@libc.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 02aeb2f21530c98fc3ca51028eda742a3fafbd9f ]
pinmux_func_gpios[] contains a hole due to the missing function GPIO
definition for the "CTX0&CTX1" signal, which is the logical "AND" of the
first two CAN outputs.
A closer look reveals other issues:
- Some functionality is available on alternative pins, but the
PINMUX_DATA() entries is using the wrong marks,
- Several configurations are missing.
Fix this by:
- Renaming CTX0CTX1CTX2_MARK, CRX0CRX1_PJ22_MARK, and
CRX0CRX1CRX2_PJ20_MARK to CTX0_CTX1_CTX2_MARK, CRX0_CRX1_PJ22_MARK,
resp. CRX0_CRX1_CRX2_PJ20_MARK for consistency with the
corresponding enum IDs,
- Adding all missing enum IDs and marks,
- Use the right (*_PJ2x) variants for alternative pins,
- Adding all missing configurations to pinmux_data[],
- Adding all missing function GPIO definitions to pinmux_func_gpios[].
See SH7268 Group, SH7269 Group User’s Manual: Hardware, Rev. 2.00:
[1] Table 1.4 List of Pins
[2] Figure 23.29 Connection Example when Using Channels 0 and 1 as One
Channel (64 Mailboxes × 1 Channel) and Channel 2 as One Channel
(32 Mailboxes × 1 Channel),
[3] Figure 23.30 Connection Example when Using Channels 0, 1, and 2 as
One Channel (96 Mailboxes × 1 Channel),
[4] Table 48.3 Multiplexed Pins (Port B),
[5] Table 48.4 Multiplexed Pins (Port C),
[6] Table 48.10 Multiplexed Pins (Port J),
[7] Section 48.2.4 Port B Control Registers 0 to 5 (PBCR0 to PBCR5).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20191218194812.12741-5-geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 884caadad128efad8e00c1cdc3177bc8912ee8ec ]
The definitions for bit field [19:18] of the Peripheral Function Select
Register 3 were accidentally copied from bit field [20], leading to
duplicates for the TCLK1_B function, and missing TCLK0, CAN_CLK_B, and
ET0_ETXD4 functions.
Fix this by adding the missing GPIO_FN_CAN_CLK_B and GPIO_FN_ET0_ETXD4
enum values, and correcting the functions.
Reported-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20191024131308.16659-1-geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
The naming of pgtable_page_{ctor,dtor}() seems to have confused a few
people, and until recently arm64 used these erroneously/pointlessly for
other levels of page table.
To make it incredibly clear that these only apply to the PTE level, and to
align with the naming of pgtable_pmd_page_{ctor,dtor}(), let's rename them
to pgtable_pte_page_{ctor,dtor}().
These changes were generated with the following shell script:
----
git grep -lw 'pgtable_page_.tor' | while read FILE; do
sed -i '{s/pgtable_page_ctor/pgtable_pte_page_ctor/}' $FILE;
sed -i '{s/pgtable_page_dtor/pgtable_pte_page_dtor/}' $FILE;
done
----
... with the documentation re-flowed to remain under 80 columns, and
whitespace fixed up in macros to keep backslashes aligned.
There should be no functional change as a result of this patch.
Link: http://lkml.kernel.org/r/20190722141133.3116-1-mark.rutland@arm.com
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Mike Rapoport <rppt@linux.ibm.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> [m68k]
Cc: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Yu Zhao <yuzhao@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Both pgtable_cache_init() and pgd_cache_init() are used to initialize kmem
cache for page table allocations on several architectures that do not use
PAGE_SIZE tables for one or more levels of the page table hierarchy.
Most architectures do not implement these functions and use __weak default
NOP implementation of pgd_cache_init(). Since there is no such default
for pgtable_cache_init(), its empty stub is duplicated among most
architectures.
Rename the definitions of pgd_cache_init() to pgtable_cache_init() and
drop empty stubs of pgtable_cache_init().
Link: http://lkml.kernel.org/r/1566457046-22637-1-git-send-email-rppt@linux.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Acked-by: Will Deacon <will@kernel.org> [arm64]
Acked-by: Thomas Gleixner <tglx@linutronix.de> [x86]
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The sh implementation pte_alloc_one(), pte_alloc_one_kernel(),
pte_free_kernel() and pte_free() is identical to the generic except of
lack of __GFP_ACCOUNT for the user PTEs allocation.
Switch sh to use generic version of these functions.
Link: http://lkml.kernel.org/r/1565250728-21721-4-git-send-email-rppt@linux.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patch series "mm: remove quicklist page table caches".
A while ago Nicholas proposed to remove quicklist page table caches [1].
I've rebased his patch on the curren upstream and switched ia64 and sh to
use generic versions of PTE allocation.
[1] https://lore.kernel.org/linux-mm/20190711030339.20892-1-npiggin@gmail.com
This patch (of 3):
Remove page table allocator "quicklists". These have been around for a
long time, but have not got much traction in the last decade and are only
used on ia64 and sh architectures.
The numbers in the initial commit look interesting but probably don't
apply anymore. If anybody wants to resurrect this it's in the git
history, but it's unhelpful to have this code and divergent allocator
behaviour for minor archs.
Also it might be better to instead make more general improvements to page
allocator if this is still so slow.
Link: http://lkml.kernel.org/r/1565250728-21721-2-git-send-email-rppt@linux.ibm.com
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
UAPI headers licensed under GPL are supposed to have exception
"WITH Linux-syscall-note" so that they can be included into non-GPL
user space application code.
The exception note is missing in some UAPI headers.
Some of them slipped in by the treewide conversion commit b24413180f
("License cleanup: add SPDX GPL-2.0 license identifier to files with
no license"). Just run:
$ git show --oneline b24413180f -- arch/x86/include/uapi/asm/
I believe they are not intentional, and should be fixed too.
This patch was generated by the following script:
git grep -l --not -e Linux-syscall-note --and -e SPDX-License-Identifier \
-- :arch/*/include/uapi/asm/*.h :include/uapi/ :^*/Kbuild |
while read file
do
sed -i -e '/[[:space:]]OR[[:space:]]/s/\(GPL-[^[:space:]]*\)/(\1 WITH Linux-syscall-note)/g' \
-e '/[[:space:]]or[[:space:]]/s/\(GPL-[^[:space:]]*\)/(\1 WITH Linux-syscall-note)/g' \
-e '/[[:space:]]OR[[:space:]]/!{/[[:space:]]or[[:space:]]/!s/\(GPL-[^[:space:]]*\)/\1 WITH Linux-syscall-note/g}' $file
done
After this patch is applied, there are 5 UAPI headers that do not contain
"WITH Linux-syscall-note". They are kept untouched since this exception
applies only to GPL variants.
$ git grep --not -e Linux-syscall-note --and -e SPDX-License-Identifier \
-- :arch/*/include/uapi/asm/*.h :include/uapi/ :^*/Kbuild
include/uapi/drm/panfrost_drm.h:/* SPDX-License-Identifier: MIT */
include/uapi/linux/batman_adv.h:/* SPDX-License-Identifier: MIT */
include/uapi/linux/qemu_fw_cfg.h:/* SPDX-License-Identifier: BSD-3-Clause */
include/uapi/linux/vbox_err.h:/* SPDX-License-Identifier: MIT */
include/uapi/linux/virtio_iommu.h:/* SPDX-License-Identifier: BSD-3-Clause */
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The asm-generic changes for 5.3 consist of a cleanup series from
Christoph Hellwig, who explains:
"asm-generic/ptrace.h is a little weird in that it doesn't actually
implement any functionality, but it provided multiple layers of macros
that just implement trivial inline functions. We implement those
directly in the few architectures and be off with a much simpler
design."
Link: https://lore.kernel.org/lkml/20190624054728.30966-1-hch@lst.de/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=jkfI
-----END PGP SIGNATURE-----
Merge tag 'asm-generic-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic updates from Arnd Bergmann:
"The asm-generic changes for 5.3 consist of a cleanup series to remove
ptrace.h from Christoph Hellwig, who explains:
'asm-generic/ptrace.h is a little weird in that it doesn't actually
implement any functionality, but it provided multiple layers of
macros that just implement trivial inline functions. We implement
those directly in the few architectures and be off with a much
simpler design.'
at https://lore.kernel.org/lkml/20190624054728.30966-1-hch@lst.de/"
* tag 'asm-generic-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
asm-generic: remove ptrace.h
x86: don't use asm-generic/ptrace.h
sh: don't use asm-generic/ptrace.h
powerpc: don't use asm-generic/ptrace.h
arm64: don't use asm-generic/ptrace.h
The sh code is mostly equivalent to the generic one, minus various
bugfixes and two arch overrides that this patch adds to pgtable.h.
Link: http://lkml.kernel.org/r/20190625143715.1689-7-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Andrey Konovalov <andreyknvl@google.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: David Miller <davem@davemloft.net>
Cc: James Hogan <jhogan@kernel.org>
Cc: Jason Gunthorpe <jgg@mellanox.com>
Cc: Khalid Aziz <khalid.aziz@oracle.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Rich Felker <dalias@libc.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
sh only had pud_page_vaddr, but not pud_page.
[hch@lst.de: sh: stub out pud_page]
Link: http://lkml.kernel.org/r/20190701151818.32227-2-hch@lst.de
Link: http://lkml.kernel.org/r/20190625143715.1689-6-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Cc: Andrey Konovalov <andreyknvl@google.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: David Miller <davem@davemloft.net>
Cc: James Hogan <jhogan@kernel.org>
Cc: Jason Gunthorpe <jgg@mellanox.com>
Cc: Khalid Aziz <khalid.aziz@oracle.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Rich Felker <dalias@libc.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When building drm/exynos for sh, as part of an allmodconfig build, the
following warning triggered:
exynos7_drm_decon.c: In function `decon_remove':
exynos7_drm_decon.c:769:24: warning: unused variable `ctx'
struct decon_context *ctx = dev_get_drvdata(&pdev->dev);
The ctx variable is only used as argument to iounmap().
In sh - allmodconfig CONFIG_MMU is not defined
so it ended up in:
\#define __iounmap(addr) do { } while (0)
\#define iounmap __iounmap
Fix the warning by introducing a static inline function for iounmap.
This is similar to several other architectures.
Link: http://lkml.kernel.org/r/20190622114208.24427-1-sam@ravnborg.org
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Rich Felker <dalias@libc.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Doing the indirection through macros for the regs accessors just
makes them harder to read, so implement the helpers directly.
Note that only the helpers actually used are implemented now.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This will eventually allow us to kill the need for an <asm/flat.h> for
many cases.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Vladimir Murzin <vladimir.murzin@arm.com>
Reviewed-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Instead add a Kconfig variable that only h8300 selects.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
This way only the two architectures that do masking need to provide
the helper.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Vladimir Murzin <vladimir.murzin@arm.com>
Reviewed-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
This helper is a no-op on all architectures, remove it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Vladimir Murzin <vladimir.murzin@arm.com>
Reviewed-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
This helper is the same for all architectures, open code it in the only
caller.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Vladimir Murzin <vladimir.murzin@arm.com>
Reviewed-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Now that all instances of #include <asm/sizes.h> have been replaced with
#include <linux/sizes.h>, we can remove these.
Link: http://lkml.kernel.org/r/1553267665-27228-2-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nex drivers:
- New driver for Bitmain BM1880 pin controller
- New driver for Mediatek MT8516
- New driver for Cirrus Logich Lochnagar PMIC pins
Updates:
- Incremental development on Renesas SH-PFC
- Incremental development on Intel pin controller and some
particular updates for Cedarfork.
- Pin configuration support in Allwinner SunXi drivers
- Suspend/resume support in the NXP/Freescale i.MX8MQ driver
- Support for more packaging of the ST Micro STM32
-----BEGIN PGP SIGNATURE-----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=ovk5
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"It is pretty calm and chill in pin control for the moment. Just
incremental development.
There is an odd patch to the Super-H architecture, it's coming from
the maintainers so should be fine.
Summary:
New drivers:
- Bitmain BM1880 pin controller
- Mediatek MT8516
- Cirrus Logich Lochnagar PMIC pins
Updates:
- Incremental development on Renesas SH-PFC
- Incremental development on Intel pin controller and some particular
updates for Cedarfork.
- Pin configuration support in Allwinner SunXi drivers
- Suspend/resume support in the NXP/Freescale i.MX8MQ driver
- Support for more packaging of the ST Micro STM32"
* tag 'pinctrl-v5.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (72 commits)
pinctrl: mcp23s08: Do not complain about unsupported params
pinctrl: Rework Kconfig dependency for BM1880 pinctrl driver
MAINTAINERS: Add entry for BM1880 pinctrl
pinctrl: Add pinctrl support for BM1880 SoC
dt-bindings: pinctrl: Add BM1880 pinctrl binding
pinctrl: stm32: check irq controller availability at probe
pinctrl: mediatek: Add MT8516 Pinctrl driver
pinctrl: zte: fix leaked of_node references
pinctrl: intel: Increase readability of intel_gpio_update_pad_mode()
pinctrl: intel: Retain HOSTSW_OWN for requested gpio pin
pinctrl: pistachio: fix leaked of_node references
pinctrl: sunxi: Support I/O bias voltage setting on H6
pinctrl: sunxi: Prepare for alternative bias voltage setting methods
pinctrl: st: fix leaked of_node references
pinctrl: samsung: fix leaked of_node references
pinctrl: stm32: align stm32mp157 pin names
pinctrl: stm32: add package information for stm32mp157c
pinctrl: stm32: introduce package support
dt-bindings: pinctrl: stm32: add new entry for package information
pinctrl: imx8mq: Add suspend/resume ops
...
Pull networking updates from David Miller:
"Highlights:
1) Support AES128-CCM ciphers in kTLS, from Vakul Garg.
2) Add fib_sync_mem to control the amount of dirty memory we allow to
queue up between synchronize RCU calls, from David Ahern.
3) Make flow classifier more lockless, from Vlad Buslov.
4) Add PHY downshift support to aquantia driver, from Heiner
Kallweit.
5) Add SKB cache for TCP rx and tx, from Eric Dumazet. This reduces
contention on SLAB spinlocks in heavy RPC workloads.
6) Partial GSO offload support in XFRM, from Boris Pismenny.
7) Add fast link down support to ethtool, from Heiner Kallweit.
8) Use siphash for IP ID generator, from Eric Dumazet.
9) Pull nexthops even further out from ipv4/ipv6 routes and FIB
entries, from David Ahern.
10) Move skb->xmit_more into a per-cpu variable, from Florian
Westphal.
11) Improve eBPF verifier speed and increase maximum program size,
from Alexei Starovoitov.
12) Eliminate per-bucket spinlocks in rhashtable, and instead use bit
spinlocks. From Neil Brown.
13) Allow tunneling with GUE encap in ipvs, from Jacky Hu.
14) Improve link partner cap detection in generic PHY code, from
Heiner Kallweit.
15) Add layer 2 encap support to bpf_skb_adjust_room(), from Alan
Maguire.
16) Remove SKB list implementation assumptions in SCTP, your's truly.
17) Various cleanups, optimizations, and simplifications in r8169
driver. From Heiner Kallweit.
18) Add memory accounting on TX and RX path of SCTP, from Xin Long.
19) Switch PHY drivers over to use dynamic featue detection, from
Heiner Kallweit.
20) Support flow steering without masking in dpaa2-eth, from Ioana
Ciocoi.
21) Implement ndo_get_devlink_port in netdevsim driver, from Jiri
Pirko.
22) Increase the strict parsing of current and future netlink
attributes, also export such policies to userspace. From Johannes
Berg.
23) Allow DSA tag drivers to be modular, from Andrew Lunn.
24) Remove legacy DSA probing support, also from Andrew Lunn.
25) Allow ll_temac driver to be used on non-x86 platforms, from Esben
Haabendal.
26) Add a generic tracepoint for TX queue timeouts to ease debugging,
from Cong Wang.
27) More indirect call optimizations, from Paolo Abeni"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1763 commits)
cxgb4: Fix error path in cxgb4_init_module
net: phy: improve pause mode reporting in phy_print_status
dt-bindings: net: Fix a typo in the phy-mode list for ethernet bindings
net: macb: Change interrupt and napi enable order in open
net: ll_temac: Improve error message on error IRQ
net/sched: remove block pointer from common offload structure
net: ethernet: support of_get_mac_address new ERR_PTR error
net: usb: smsc: fix warning reported by kbuild test robot
staging: octeon-ethernet: Fix of_get_mac_address ERR_PTR check
net: dsa: support of_get_mac_address new ERR_PTR error
net: dsa: sja1105: Fix status initialization in sja1105_get_ethtool_stats
vrf: sit mtu should not be updated when vrf netdev is the link
net: dsa: Fix error cleanup path in dsa_init_module
l2tp: Fix possible NULL pointer dereference
taprio: add null check on sched_nest to avoid potential null pointer dereference
net: mvpp2: cls: fix less than zero check on a u32 variable
net_sched: sch_fq: handle non connected flows
net_sched: sch_fq: do not assume EDT packets are ordered
net: hns3: use devm_kcalloc when allocating desc_cb
net: hns3: some cleanup for struct hns3_enet_ring
...
-----BEGIN PGP SIGNATURE-----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=p8Fp
-----END PGP SIGNATURE-----
Merge tag 'audit-pr-20190507' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit
Pull audit updates from Paul Moore:
"We've got a reasonably broad set of audit patches for the v5.2 merge
window, the highlights are below:
- The biggest change, and the source of all the arch/* changes, is
the patchset from Dmitry to help enable some of the work he is
doing around PTRACE_GET_SYSCALL_INFO.
To be honest, including this in the audit tree is a bit of a
stretch, but it does help move audit a little further along towards
proper syscall auditing for all arches, and everyone else seemed to
agree that audit was a "good" spot for this to land (or maybe they
just didn't want to merge it? dunno.).
- We can now audit time/NTP adjustments.
- We continue the work to connect associated audit records into a
single event"
* tag 'audit-pr-20190507' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit: (21 commits)
audit: fix a memory leak bug
ntp: Audit NTP parameters adjustment
timekeeping: Audit clock adjustments
audit: purge unnecessary list_empty calls
audit: link integrity evm_write_xattrs record to syscall event
syscall_get_arch: add "struct task_struct *" argument
unicore32: define syscall_get_arch()
Move EM_UNICORE to uapi/linux/elf-em.h
nios2: define syscall_get_arch()
nds32: define syscall_get_arch()
Move EM_NDS32 to uapi/linux/elf-em.h
m68k: define syscall_get_arch()
hexagon: define syscall_get_arch()
Move EM_HEXAGON to uapi/linux/elf-em.h
h8300: define syscall_get_arch()
c6x: define syscall_get_arch()
arc: define syscall_get_arch()
Move EM_ARCOMPACT and EM_ARCV2 to uapi/linux/elf-em.h
audit: Make audit_log_cap and audit_copy_inode static
audit: connect LOGIN record to its syscall record
...
Remove mmiowb() from the kernel memory barrier API and instead, for
architectures that need it, hide the barrier inside spin_unlock() when
MMIO has been performed inside the critical section.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEPxTL6PPUbjXGY88ct6xw3ITBYzQFAlzMFaUACgkQt6xw3ITB
YzRICQgAiv7wF/yIbBhDOmCNCAKDO59chvFQWxXWdGk/aAB56kwKAMXJgLOvlMG/
VRuuLyParTFQETC3jaxKgnO/1hb+PZLDt2Q2KqixtjIzBypKUPWvK2sf6THhSRF1
GK0DBVUd1rCrWrR815+SPb8el4xXtdBzvAVB+Fx35PXVNpdRdqCkK+EQ6UnXGokm
rXXHbnfsnquBDtmb4CR4r2beH+aNElXbdt0Kj8VcE5J7f7jTdW3z6Q9WFRvdKmK7
yrsxXXB2w/EsWXOwFp0SLTV5+fgeGgTvv8uLjDw+SG6t0E0PebxjNAflT7dPrbYL
WecjKC9WqBxrGY+4ew6YJP70ijLBCw==
=aC8m
-----END PGP SIGNATURE-----
Merge tag 'arm64-mmiowb' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull mmiowb removal from Will Deacon:
"Remove Mysterious Macro Intended to Obscure Weird Behaviours (mmiowb())
Remove mmiowb() from the kernel memory barrier API and instead, for
architectures that need it, hide the barrier inside spin_unlock() when
MMIO has been performed inside the critical section.
The only relatively recent changes have been addressing review
comments on the documentation, which is in a much better shape thanks
to the efforts of Ben and Ingo.
I was initially planning to split this into two pull requests so that
you could run the coccinelle script yourself, however it's been plain
sailing in linux-next so I've just included the whole lot here to keep
things simple"
* tag 'arm64-mmiowb' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (23 commits)
docs/memory-barriers.txt: Update I/O section to be clearer about CPU vs thread
docs/memory-barriers.txt: Fix style, spacing and grammar in I/O section
arch: Remove dummy mmiowb() definitions from arch code
net/ethernet/silan/sc92031: Remove stale comment about mmiowb()
i40iw: Redefine i40iw_mmiowb() to do nothing
scsi/qla1280: Remove stale comment about mmiowb()
drivers: Remove explicit invocations of mmiowb()
drivers: Remove useless trailing comments from mmiowb() invocations
Documentation: Kill all references to mmiowb()
riscv/mmiowb: Hook up mmwiob() implementation to asm-generic code
powerpc/mmiowb: Hook up mmwiob() implementation to asm-generic code
ia64/mmiowb: Add unconditional mmiowb() to arch_spin_unlock()
mips/mmiowb: Add unconditional mmiowb() to arch_spin_unlock()
sh/mmiowb: Add unconditional mmiowb() to arch_spin_unlock()
m68k/io: Remove useless definition of mmiowb()
nds32/io: Remove useless definition of mmiowb()
x86/io: Remove useless definition of mmiowb()
arm64/io: Remove useless definition of mmiowb()
ARM/io: Remove useless definition of mmiowb()
mmiowb: Hook up mmiowb helpers to spinlocks and generic I/O accessors
...
Pull locking updates from Ingo Molnar:
"Here are the locking changes in this cycle:
- rwsem unification and simpler micro-optimizations to prepare for
more intrusive (and more lucrative) scalability improvements in
v5.3 (Waiman Long)
- Lockdep irq state tracking flag usage cleanups (Frederic
Weisbecker)
- static key improvements (Jakub Kicinski, Peter Zijlstra)
- misc updates, cleanups and smaller fixes"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (26 commits)
locking/lockdep: Remove unnecessary unlikely()
locking/static_key: Don't take sleeping locks in __static_key_slow_dec_deferred()
locking/static_key: Factor out the fast path of static_key_slow_dec()
locking/static_key: Add support for deferred static branches
locking/lockdep: Test all incompatible scenarios at once in check_irq_usage()
locking/lockdep: Avoid bogus Clang warning
locking/lockdep: Generate LOCKF_ bit composites
locking/lockdep: Use expanded masks on find_usage_*() functions
locking/lockdep: Map remaining magic numbers to lock usage mask names
locking/lockdep: Move valid_state() inside CONFIG_TRACE_IRQFLAGS && CONFIG_PROVE_LOCKING
locking/rwsem: Prevent unneeded warning during locking selftest
locking/rwsem: Optimize rwsem structure for uncontended lock acquisition
locking/rwsem: Enable lock event counting
locking/lock_events: Don't show pvqspinlock events on bare metal
locking/lock_events: Make lock_events available for all archs & other locks
locking/qspinlock_stat: Introduce generic lockevent_*() counting APIs
locking/rwsem: Enhance DEBUG_RWSEMS_WARN_ON() macro
locking/rwsem: Add debug check for __down_read*()
locking/rwsem: Micro-optimize rwsem_try_read_lock_unqueued()
locking/rwsem: Move rwsem internal function declarations to rwsem-xadd.h
...
Pull unified TLB flushing from Ingo Molnar:
"This contains the generic mmu_gather feature from Peter Zijlstra,
which is an all-arch unification of TLB flushing APIs, via the
following (broad) steps:
- enhance the <asm-generic/tlb.h> APIs to cover more arch details
- convert most TLB flushing arch implementations to the generic
<asm-generic/tlb.h> APIs.
- remove leftovers of per arch implementations
After this series every single architecture makes use of the unified
TLB flushing APIs"
* 'core-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
mm/resource: Use resource_overlaps() to simplify region_intersects()
ia64/tlb: Eradicate tlb_migrate_finish() callback
asm-generic/tlb: Remove tlb_table_flush()
asm-generic/tlb: Remove tlb_flush_mmu_free()
asm-generic/tlb: Remove CONFIG_HAVE_GENERIC_MMU_GATHER
asm-generic/tlb: Remove arch_tlb*_mmu()
s390/tlb: Convert to generic mmu_gather
asm-generic/tlb: Introduce CONFIG_HAVE_MMU_GATHER_NO_GATHER=y
arch/tlb: Clean up simple architectures
um/tlb: Convert to generic mmu_gather
sh/tlb: Convert SH to generic mmu_gather
ia64/tlb: Convert to generic mmu_gather
arm/tlb: Convert to generic mmu_gather
asm-generic/tlb, arch: Invert CONFIG_HAVE_RCU_TABLE_INVALIDATE
asm-generic/tlb, ia64: Conditionally provide tlb_migrate_finish()
asm-generic/tlb: Provide generic tlb_flush() based on flush_tlb_mm()
asm-generic/tlb, arch: Provide generic tlb_flush() based on flush_tlb_range()
asm-generic/tlb, arch: Provide generic VIPT cache flush
asm-generic/tlb, arch: Provide CONFIG_HAVE_MMU_GATHER_PAGE_SIZE
asm-generic/tlb: Provide a comment
The 'timeval' and 'timespec' data structures used for socket timestamps
are going to be redefined in user space based on 64-bit time_t in future
versions of the C library to deal with the y2038 overflow problem,
which breaks the ABI definition.
Unlike many modern ioctl commands, SIOCGSTAMP and SIOCGSTAMPNS do not
use the _IOR() macro to encode the size of the transferred data, so it
remains ambiguous whether the application uses the old or new layout.
The best workaround I could find is rather ugly: we redefine the command
code based on the size of the respective data structure with a ternary
operator. This lets it get evaluated as late as possible, hopefully after
that structure is visible to the caller. We cannot use an #ifdef here,
because inux/sockios.h might have been included before any libc header
that could determine the size of time_t.
The ioctl implementation now interprets the new command codes as always
referring to the 64-bit structure on all architectures, while the old
architecture specific command code still refers to the old architecture
specific layout. The new command number is only used when they are
actually different.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mmiowb() macro is horribly difficult to use and drivers will continue
to work most of the time if they omit a call when it is required.
Rather than rely on driver authors getting this right, push mmiowb() into
arch_spin_unlock() for sh. If this is deemed to be a performance issue,
a subsequent optimisation could make use of ARCH_HAS_MMIOWB to elide
the barrier in cases where no I/O writes were performed inside the
critical section.
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Rich Felker <dalias@libc.org>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Hook up asm-generic/mmiowb.h to Kbuild for all architectures so that we
can subsequently include asm/mmiowb.h from core code.
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
As the generic rwsem-xadd code is using the appropriate acquire and
release versions of the atomic operations, the arch specific rwsem.h
files will not be that much faster than the generic code as long as the
atomic functions are properly implemented. So we can remove those arch
specific rwsem.h and stop building asm/rwsem.h to reduce maintenance
effort.
Currently, only x86, alpha and ia64 have implemented architecture
specific fast paths. I don't have access to alpha and ia64 systems for
testing, but they are legacy systems that are not likely to be updated
to the latest kernel anyway.
By using a rwsem microbenchmark, the total locking rates on a 4-socket
56-core 112-thread x86-64 system before and after the patch were as
follows (mixed means equal # of read and write locks):
Before Patch After Patch
# of Threads wlock rlock mixed wlock rlock mixed
------------ ----- ----- ----- ----- ----- -----
1 29,201 30,143 29,458 28,615 30,172 29,201
2 6,807 13,299 1,171 7,725 15,025 1,804
4 6,504 12,755 1,520 7,127 14,286 1,345
8 6,762 13,412 764 6,826 13,652 726
16 6,693 15,408 662 6,599 15,938 626
32 6,145 15,286 496 5,549 15,487 511
64 5,812 15,495 60 5,858 15,572 60
There were some run-to-run variations for the multi-thread tests. For
x86-64, using the generic C code fast path seems to be a little bit
faster than the assembly version with low lock contention. Looking at
the assembly version of the fast paths, there are assembly to/from C
code wrappers that save and restore all the callee-clobbered registers
(7 registers on x86-64). The assembly generated from the generic C
code doesn't need to do that. That may explain the slight performance
gain here.
The generic asm rwsem.h can also be merged into kernel/locking/rwsem.h
with no code change as no other code other than those under
kernel/locking needs to access the internal rwsem macros and functions.
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-c6x-dev@linux-c6x.org
Cc: linux-m68k@lists.linux-m68k.org
Cc: linux-riscv@lists.infradead.org
Cc: linux-um@lists.infradead.org
Cc: linux-xtensa@linux-xtensa.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: nios2-dev@lists.rocketboards.org
Cc: openrisc@lists.librecores.org
Cc: uclinux-h8-devel@lists.sourceforge.jp
Link: https://lkml.kernel.org/r/20190322143008.21313-2-longman@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Move the mmu_gather::page_size things into the generic code instead of
PowerPC specific bits.
No change in behavior intended.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Nick Piggin <npiggin@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@surriel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
When compile-testing on arm:
arch/sh/include/cpu-sh4/cpu/sh7786.h: In function ‘sh7786_mm_sel’:
arch/sh/include/cpu-sh4/cpu/sh7786.h:135:21: warning: passing argument 1 of ‘__raw_readl’ makes pointer from integer without a cast [-Wint-conversion]
return __raw_readl(0xFC400020) & 0x7;
^~~~~~~~~~
In file included from include/linux/io.h:25:0,
from arch/sh/include/cpu-sh4/cpu/sh7786.h:14,
from drivers/pinctrl/sh-pfc/pfc-sh7786.c:15:
arch/arm/include/asm/io.h:113:21: note: expected ‘const volatile void *’ but argument is of type ‘unsigned int’
#define __raw_readl __raw_readl
^
arch/arm/include/asm/io.h:114:19: note: in expansion of macro ‘__raw_readl’
static inline u32 __raw_readl(const volatile void __iomem *addr)
^~~~~~~~~~~
__raw_readl() on SuperH is a macro that casts the passed I/O address to
the correct type, while the implementations on most other architectures
expect to be passed the correct pointer type.
Add an explicit cast to fix this.
Note that this also gets rid of a sparse warning on SuperH:
arch/sh/include/cpu-sh4/cpu/sh7786.h:135:16: warning: incorrect type in argument 1 (different base types)
arch/sh/include/cpu-sh4/cpu/sh7786.h:135:16: expected void const volatile [noderef] <asn:2>*<noident>
arch/sh/include/cpu-sh4/cpu/sh7786.h:135:16: got unsigned int
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
I do not see any consistency about headers_install of <linux/kvm_para.h>
and <asm/kvm_para.h>.
According to my analysis of Linux 5.1-rc1, there are 3 groups:
[1] Both <linux/kvm_para.h> and <asm/kvm_para.h> are exported
alpha, arm, hexagon, mips, powerpc, s390, sparc, x86
[2] <asm/kvm_para.h> is exported, but <linux/kvm_para.h> is not
arc, arm64, c6x, h8300, ia64, m68k, microblaze, nios2, openrisc,
parisc, sh, unicore32, xtensa
[3] Neither <linux/kvm_para.h> nor <asm/kvm_para.h> is exported
csky, nds32, riscv
This does not match to the actual KVM support. At least, [2] is
half-baked.
Nor do arch maintainers look like they care about this. For example,
commit 0add53713b ("microblaze: Add missing kvm_para.h to Kbuild")
exported <asm/kvm_para.h> to user-space in order to fix an in-kernel
build error.
We have two ways to make this consistent:
[A] export both <linux/kvm_para.h> and <asm/kvm_para.h> for all
architectures, irrespective of the KVM support
[B] Match the header export of <linux/kvm_para.h> and <asm/kvm_para.h>
to the KVM support
My first attempt was [A] because the code looks cleaner, but Paolo
suggested [B].
So, this commit goes with [B].
For most architectures, <asm/kvm_para.h> was moved to the kernel-space.
I changed include/uapi/linux/Kbuild so that it checks generated
asm/kvm_para.h as well as check-in ones.
After this commit, there will be two groups:
[1] Both <linux/kvm_para.h> and <asm/kvm_para.h> are exported
arm, arm64, mips, powerpc, s390, x86
[2] Neither <linux/kvm_para.h> nor <asm/kvm_para.h> is exported
alpha, arc, c6x, csky, h8300, hexagon, ia64, m68k, microblaze,
nds32, nios2, openrisc, parisc, riscv, sh, sparc, unicore32, xtensa
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Currently, every arch/*/include/uapi/asm/Kbuild explicitly includes
the common Kbuild.asm file. Factor out the duplicated include directives
to scripts/Makefile.asm-generic so that no architecture would opt out
of the mandatory-y mechanism.
um is not forced to include mandatory-y since it is a very exceptional
case which does not support UAPI.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Pull year 2038 updates from Thomas Gleixner:
"Another round of changes to make the kernel ready for 2038. After lots
of preparatory work this is the first set of syscalls which are 2038
safe:
403 clock_gettime64
404 clock_settime64
405 clock_adjtime64
406 clock_getres_time64
407 clock_nanosleep_time64
408 timer_gettime64
409 timer_settime64
410 timerfd_gettime64
411 timerfd_settime64
412 utimensat_time64
413 pselect6_time64
414 ppoll_time64
416 io_pgetevents_time64
417 recvmmsg_time64
418 mq_timedsend_time64
419 mq_timedreceiv_time64
420 semtimedop_time64
421 rt_sigtimedwait_time64
422 futex_time64
423 sched_rr_get_interval_time64
The syscall numbers are identical all over the architectures"
* 'timers-2038-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (36 commits)
riscv: Use latest system call ABI
checksyscalls: fix up mq_timedreceive and stat exceptions
unicore32: Fix __ARCH_WANT_STAT64 definition
asm-generic: Make time32 syscall numbers optional
asm-generic: Drop getrlimit and setrlimit syscalls from default list
32-bit userspace ABI: introduce ARCH_32BIT_OFF_T config option
compat ABI: use non-compat openat and open_by_handle_at variants
y2038: add 64-bit time_t syscalls to all 32-bit architectures
y2038: rename old time and utime syscalls
y2038: remove struct definition redirects
y2038: use time32 syscall names on 32-bit
syscalls: remove obsolete __IGNORE_ macros
y2038: syscalls: rename y2038 compat syscalls
x86/x32: use time64 versions of sigtimedwait and recvmmsg
timex: change syscalls to use struct __kernel_timex
timex: use __kernel_timex internally
sparc64: add custom adjtimex/clock_adjtime functions
time: fix sys_timer_settime prototype
time: Add struct __kernel_timex
time: make adjtime compat handling available for 32 bit
...
Every in-kernel use of this function defined it to KERNEL_DS (either as
an actual define, or as an inline function). It's an entirely
historical artifact, and long long long ago used to actually read the
segment selector valueof '%ds' on x86.
Which in the kernel is always KERNEL_DS.
Inspired by a patch from Jann Horn that just did this for a very small
subset of users (the ones in fs/), along with Al who suggested a script.
I then just took it to the logical extreme and removed all the remaining
gunk.
Roughly scripted with
git grep -l '(get_ds())' -- :^tools/ | xargs sed -i 's/(get_ds())/(KERNEL_DS)/'
git grep -lw 'get_ds' -- :^tools/ | xargs sed -i '/^#define get_ds()/d'
plus manual fixups to remove a few unusual usage patterns, the couple of
inline function cases and to fix up a comment that had become stale.
The 'get_ds()' function remains in an x86 kvm selftest, since in user
space it actually does something relevant.
Inspired-by: Jann Horn <jannh@google.com>
Inspired-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The time, stime, utime, utimes, and futimesat system calls are only
used on older architectures, and we do not provide y2038 safe variants
of them, as they are replaced by clock_gettime64, clock_settime64,
and utimensat_time64.
However, for consistency it seems better to have the 32-bit architectures
that still use them call the "time32" entry points (leaving the
traditional handlers for the 64-bit architectures), like we do for system
calls that now require two versions.
Note: We used to always define __ARCH_WANT_SYS_TIME and
__ARCH_WANT_SYS_UTIME and only set __ARCH_WANT_COMPAT_SYS_TIME and
__ARCH_WANT_SYS_UTIME32 for compat mode on 64-bit kernels. Now this is
reversed: only 64-bit architectures set __ARCH_WANT_SYS_TIME/UTIME, while
we need __ARCH_WANT_SYS_TIME32/UTIME32 for 32-bit architectures and compat
mode. The resulting asm/unistd.h changes look a bit counterintuitive.
This is only a cleanup patch and it should not change any behavior.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
When I merged this patch, the file was accidentally left intact
instead of being removed, which means any changes to syscall.tbl
have no effect.
Fixes: 2b3c5a99d5 ("sh: generate uapi header and syscall table header files")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- improve boolinit.cocci and use_after_iter.cocci semantic patches
- fix alignment for kallsyms
- move 'asm goto' compiler test to Kconfig and clean up jump_label
CONFIG option
- generate asm-generic wrappers automatically if arch does not implement
mandatory UAPI headers
- remove redundant generic-y defines
- misc cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=I+r6
-----END PGP SIGNATURE-----
Merge tag 'kbuild-v4.21-3' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild updates from Masahiro Yamada:
- improve boolinit.cocci and use_after_iter.cocci semantic patches
- fix alignment for kallsyms
- move 'asm goto' compiler test to Kconfig and clean up jump_label
CONFIG option
- generate asm-generic wrappers automatically if arch does not
implement mandatory UAPI headers
- remove redundant generic-y defines
- misc cleanups
* tag 'kbuild-v4.21-3' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kconfig: rename generated .*conf-cfg to *conf-cfg
kbuild: remove unnecessary stubs for archheader and archscripts
kbuild: use assignment instead of define ... endef for filechk_* rules
arch: remove redundant UAPI generic-y defines
kbuild: generate asm-generic wrappers if mandatory headers are missing
arch: remove stale comments "UAPI Header export list"
riscv: remove redundant kernel-space generic-y
kbuild: change filechk to surround the given command with { }
kbuild: remove redundant target cleaning on failure
kbuild: clean up rule_dtc_dt_yaml
kbuild: remove UIMAGE_IN and UIMAGE_OUT
jump_label: move 'asm goto' support test to Kconfig
kallsyms: lower alignment on ARM
scripts: coccinelle: boolinit: drop warnings on named constants
scripts: coccinelle: check for redeclaration
kconfig: remove unused "file" field of yylval union
nds32: remove redundant kernel-space generic-y
nios2: remove unneeded HAS_DMA define
Commit 594cc251fd ("make 'user_access_begin()' do 'access_ok()'")
broke both alpha and SH booting in qemu, as noticed by Guenter Roeck.
It turns out that the bug wasn't actually in that commit itself (which
would have been surprising: it was mostly a no-op), but in how the
addition of access_ok() to the strncpy_from_user() and strnlen_user()
functions now triggered the case where those functions would test the
access of the very last byte of the user address space.
The string functions actually did that user range test before too, but
they did it manually by just comparing against user_addr_max(). But
with user_access_begin() doing the check (using "access_ok()"), it now
exposed problems in the architecture implementations of that function.
For example, on alpha, the access_ok() helper macro looked like this:
#define __access_ok(addr, size) \
((get_fs().seg & (addr | size | (addr+size))) == 0)
and what it basically tests is of any of the high bits get set (the
USER_DS masking value is 0xfffffc0000000000).
And that's completely wrong for the "addr+size" check. Because it's
off-by-one for the case where we check to the very end of the user
address space, which is exactly what the strn*_user() functions do.
Why? Because "addr+size" will be exactly the size of the address space,
so trying to access the last byte of the user address space will fail
the __access_ok() check, even though it shouldn't. As a result, the
user string accessor functions failed consistently - because they
literally don't know how long the string is going to be, and the max
access is going to be that last byte of the user address space.
Side note: that alpha macro is buggy for another reason too - it re-uses
the arguments twice.
And SH has another version of almost the exact same bug:
#define __addr_ok(addr) \
((unsigned long __force)(addr) < current_thread_info()->addr_limit.seg)
so far so good: yes, a user address must be below the limit. But then:
#define __access_ok(addr, size) \
(__addr_ok((addr) + (size)))
is wrong with the exact same off-by-one case: the case when "addr+size"
is exactly _equal_ to the limit is actually perfectly fine (think "one
byte access at the last address of the user address space")
The SH version is actually seriously buggy in another way: it doesn't
actually check for overflow, even though it did copy the _comment_ that
talks about overflow.
So it turns out that both SH and alpha actually have completely buggy
implementations of access_ok(), but they happened to work in practice
(although the SH overflow one is a serious serious security bug, not
that anybody likely cares about SH security).
This fixes the problems by using a similar macro on both alpha and SH.
It isn't trying to be clever, the end address is based on this logic:
unsigned long __ao_end = __ao_a + __ao_b - !!__ao_b;
which basically says "add start and length, and then subtract one unless
the length was zero". We can't subtract one for a zero length, or we'd
just hit an underflow instead.
For a lot of access_ok() users the length is a constant, so this isn't
actually as expensive as it initially looks.
Reported-and-tested-by: Guenter Roeck <linux@roeck-us.net>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that Kbuild automatically creates asm-generic wrappers for missing
mandatory headers, it is redundant to list the same headers in
generic-y and mandatory-y.
Suggested-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
These comments are leftovers of commit fcc8487d47 ("uapi: export all
headers under uapi directories").
Prior to that commit, exported headers must be explicitly added to
header-y. Now, all headers under the uapi/ directories are exported.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Merge more updates from Andrew Morton:
- procfs updates
- various misc bits
- lib/ updates
- epoll updates
- autofs
- fatfs
- a few more MM bits
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (58 commits)
mm/page_io.c: fix polled swap page in
checkpatch: add Co-developed-by to signature tags
docs: fix Co-Developed-by docs
drivers/base/platform.c: kmemleak ignore a known leak
fs: don't open code lru_to_page()
fs/: remove caller signal_pending branch predictions
mm/: remove caller signal_pending branch predictions
arch/arc/mm/fault.c: remove caller signal_pending_branch predictions
kernel/sched/: remove caller signal_pending branch predictions
kernel/locking/mutex.c: remove caller signal_pending branch predictions
mm: select HAVE_MOVE_PMD on x86 for faster mremap
mm: speed up mremap by 20x on large regions
mm: treewide: remove unused address argument from pte_alloc functions
initramfs: cleanup incomplete rootfs
scripts/gdb: fix lx-version string output
kernel/kcov.c: mark write_comp_data() as notrace
kernel/sysctl: add panic_print into sysctl
panic: add options to print system info when panic happens
bfs: extra sanity checking and static inode bitmap
exec: separate MM_ANONPAGES and RLIMIT_STACK accounting
...
Patch series "Add support for fast mremap".
This series speeds up the mremap(2) syscall by copying page tables at
the PMD level even for non-THP systems. There is concern that the extra
'address' argument that mremap passes to pte_alloc may do something
subtle architecture related in the future that may make the scheme not
work. Also we find that there is no point in passing the 'address' to
pte_alloc since its unused. This patch therefore removes this argument
tree-wide resulting in a nice negative diff as well. Also ensuring
along the way that the enabled architectures do not do anything funky
with the 'address' argument that goes unnoticed by the optimization.
Build and boot tested on x86-64. Build tested on arm64. The config
enablement patch for arm64 will be posted in the future after more
testing.
The changes were obtained by applying the following Coccinelle script.
(thanks Julia for answering all Coccinelle questions!).
Following fix ups were done manually:
* Removal of address argument from pte_fragment_alloc
* Removal of pte_alloc_one_fast definitions from m68k and microblaze.
// Options: --include-headers --no-includes
// Note: I split the 'identifier fn' line, so if you are manually
// running it, please unsplit it so it runs for you.
virtual patch
@pte_alloc_func_def depends on patch exists@
identifier E2;
identifier fn =~
"^(__pte_alloc|pte_alloc_one|pte_alloc|__pte_alloc_kernel|pte_alloc_one_kernel)$";
type T2;
@@
fn(...
- , T2 E2
)
{ ... }
@pte_alloc_func_proto_noarg depends on patch exists@
type T1, T2, T3, T4;
identifier fn =~ "^(__pte_alloc|pte_alloc_one|pte_alloc|__pte_alloc_kernel|pte_alloc_one_kernel)$";
@@
(
- T3 fn(T1, T2);
+ T3 fn(T1);
|
- T3 fn(T1, T2, T4);
+ T3 fn(T1, T2);
)
@pte_alloc_func_proto depends on patch exists@
identifier E1, E2, E4;
type T1, T2, T3, T4;
identifier fn =~
"^(__pte_alloc|pte_alloc_one|pte_alloc|__pte_alloc_kernel|pte_alloc_one_kernel)$";
@@
(
- T3 fn(T1 E1, T2 E2);
+ T3 fn(T1 E1);
|
- T3 fn(T1 E1, T2 E2, T4 E4);
+ T3 fn(T1 E1, T2 E2);
)
@pte_alloc_func_call depends on patch exists@
expression E2;
identifier fn =~
"^(__pte_alloc|pte_alloc_one|pte_alloc|__pte_alloc_kernel|pte_alloc_one_kernel)$";
@@
fn(...
-, E2
)
@pte_alloc_macro depends on patch exists@
identifier fn =~
"^(__pte_alloc|pte_alloc_one|pte_alloc|__pte_alloc_kernel|pte_alloc_one_kernel)$";
identifier a, b, c;
expression e;
position p;
@@
(
- #define fn(a, b, c) e
+ #define fn(a, b) e
|
- #define fn(a, b) e
+ #define fn(a) e
)
Link: http://lkml.kernel.org/r/20181108181201.88826-2-joelaf@google.com
Signed-off-by: Joel Fernandes (Google) <joel@joelfernandes.org>
Suggested-by: Kirill A. Shutemov <kirill@shutemov.name>
Acked-by: Kirill A. Shutemov <kirill@shutemov.name>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Kirill A. Shutemov <kirill@shutemov.name>
Cc: William Kucharski <william.kucharski@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nobody has actually used the type (VERIFY_READ vs VERIFY_WRITE) argument
of the user address range verification function since we got rid of the
old racy i386-only code to walk page tables by hand.
It existed because the original 80386 would not honor the write protect
bit when in kernel mode, so you had to do COW by hand before doing any
user access. But we haven't supported that in a long time, and these
days the 'type' argument is a purely historical artifact.
A discussion about extending 'user_access_begin()' to do the range
checking resulted this patch, because there is no way we're going to
move the old VERIFY_xyz interface to that model. And it's best done at
the end of the merge window when I've done most of my merges, so let's
just get this done once and for all.
This patch was mostly done with a sed-script, with manual fix-ups for
the cases that weren't of the trivial 'access_ok(VERIFY_xyz' form.
There were a couple of notable cases:
- csky still had the old "verify_area()" name as an alias.
- the iter_iov code had magical hardcoded knowledge of the actual
values of VERIFY_{READ,WRITE} (not that they mattered, since nothing
really used it)
- microblaze used the type argument for a debug printout
but other than those oddities this should be a total no-op patch.
I tried to fix up all architectures, did fairly extensive grepping for
access_ok() uses, and the changes are trivial, but I may have missed
something. Any missed conversion should be trivially fixable, though.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
