dt: bindings: add MARVELL's bt-sd8xxx wireless device

Add device tree binding documentation for MARVELL's bluetooth sdio
(sd8897 and sd8997) chip.

Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This commit is contained in:
Xinming Hu 2016-04-26 06:57:26 -07:00 committed by Marcel Holtmann
parent 582a1db988
commit 0065d1c5ac
2 changed files with 56 additions and 29 deletions

View File

@ -1,29 +0,0 @@
btmrvl
------
Required properties:
- compatible : must be "btmrvl,cfgdata"
Optional properties:
- btmrvl,cal-data : Calibration data downloaded to the device during
initialization. This is an array of 28 values(u8).
- btmrvl,gpio-gap : gpio and gap (in msecs) combination to be
configured.
Example:
GPIO pin 13 is configured as a wakeup source and GAP is set to 100 msecs
in below example.
btmrvl {
compatible = "btmrvl,cfgdata";
btmrvl,cal-data = /bits/ 8 <
0x37 0x01 0x1c 0x00 0xff 0xff 0xff 0xff 0x01 0x7f 0x04 0x02
0x00 0x00 0xba 0xce 0xc0 0xc6 0x2d 0x00 0x00 0x00 0x00 0x00
0x00 0x00 0xf0 0x00>;
btmrvl,gpio-gap = <0x0d64>;
};

View File

@ -0,0 +1,56 @@
Marvell 8897/8997 (sd8897/sd8997) bluetooth SDIO devices
------
Required properties:
- compatible : should be one of the following:
* "marvell,sd8897-bt"
* "marvell,sd8997-bt"
Optional properties:
- marvell,cal-data: Calibration data downloaded to the device during
initialization. This is an array of 28 values(u8).
- marvell,wakeup-pin: It represents wakeup pin number of the bluetooth chip.
firmware will use the pin to wakeup host system.
- marvell,wakeup-gap-ms: wakeup gap represents wakeup latency of the host
platform. The value will be configured to firmware. This
is needed to work chip's sleep feature as expected.
- interrupt-parent: phandle of the parent interrupt controller
- interrupts : interrupt pin number to the cpu. Driver will request an irq based
on this interrupt number. During system suspend, the irq will be
enabled so that the bluetooth chip can wakeup host platform under
certain condition. During system resume, the irq will be disabled
to make sure unnecessary interrupt is not received.
Example:
IRQ pin 119 is used as system wakeup source interrupt.
wakeup pin 13 and gap 100ms are configured so that firmware can wakeup host
using this device side pin and wakeup latency.
calibration data is also available in below example.
&mmc3 {
status = "okay";
vmmc-supply = <&wlan_en_reg>;
bus-width = <4>;
cap-power-off-card;
keep-power-in-suspend;
#address-cells = <1>;
#size-cells = <0>;
btmrvl: bluetooth@2 {
compatible = "marvell,sd8897-bt";
reg = <2>;
interrupt-parent = <&pio>;
interrupts = <119 IRQ_TYPE_LEVEL_LOW>;
marvell,cal-data = /bits/ 8 <
0x37 0x01 0x1c 0x00 0xff 0xff 0xff 0xff 0x01 0x7f 0x04 0x02
0x00 0x00 0xba 0xce 0xc0 0xc6 0x2d 0x00 0x00 0x00 0x00 0x00
0x00 0x00 0xf0 0x00>;
marvell,wakeup-pin = <0x0d>;
marvell,wakeup-gap-ms = <0x64>;
};
};